JVC CA-MXDVA9 Instructions Manual page 68

Jvc stereo system - compact component system user manual
Hide thumbs Also See for CA-MXDVA9:
Table of Contents

Advertisement

Amplifier Connection
Conexión del amplificador
Ligação do amplificador
!"
r C*U
U UL
« qO u «
Center speaker
Altavoz central
Coluna de centro
!"
‫اﻟﺴﻤﺎﻋﺔ اﻟﻮﺳﻄﻰ‬
Surround speakers
Altavoces peromètricos
Colunas surround
!"
‫اﻟﺴﻤﺎﻋﺔ اﶈﻴﻄﺔ‬
M
Amplifier output terminals
Terminales de salida de amplificador
Terminais de saida do amplificador
!"#$
‫ﻧﻬﺎﻳﺎت ﺧﺮج اﳌﻀﺨﻢ‬
Amplifier output terminals
Terminales de salida de amplificador
Terminais de saida do amplificador
!"#$
‫ﻧﻬﺎﻳﺎت ﺧﺮج اﳌﻀﺨﻢ‬
Wall mounting hole
Orificio para montaje en la pared
Furo de montagem da parede
!"
‫ﺛﻘﺐ اﻟﺘﺮﻛﻴﺐ ﻓﻲ اﳉﺪران‬
8
CONNECTION
A pin plug is attached to the tip of the speaker cord. If the speaker
connection terminal on the amplifier to which the speaker is to be
connected is a pin jack, connect the left-hand speaker's lead to the
left terminal, and the right-hand speaker's lead to the right terminal.
• Turn off power of all equipment before connecting the speakers
to the amplifier.
• The nominal impedance of the SP-XCDVB10 is 16 ohms. Con-
nect them to an amplifier with the load impedance of 16 ohms
speaker.
• The nominal impedance of the SP-XSDVB10 is 16 ohms. Con-
nect them to an amplifier with the load impedance of 16 ohms
speaker.
• The maximum power handling capacity is shown in the SPECI-
FICATIONS.
Excessive input to the speaker will result in abnormal noise and
possible damage. The following cases described below may
cause an overload of the speakers.
Be sure to lower the amplifier volume beforehand.
1) Noise during FM tuning.
2) High level signals containing high frequency components
prouduced by a tape deck in the fast forward mode.
3) Click noise produced when turning power of other compo-
nents on and off.
4) Click noise produced when connecting or disconnecting cords
with the power on.
5) Click noise when the cartridge is replaced with the power on.
6) Click noise produced when operating amplifier switches.
7) Continuous high frequency oscillation or high pitch musical
instrument sound.
8) Howling or feed back when using a microphones.
SPECIFICATIONS
SP-XCDVB10
Type
: Full range bass-reflex type
Speaker
: 8 cm (3-3/16 in.) cone × 1
Full range
Power Handling Capacity
: 30 W
: 16 Ω
Impedance
Frequency Range
: 70 Hz – 25 000 Hz
Sound Pressure Level
: 84 dB/W·m
Dimensions (W × H × D)
: 245 mm × 110 mm × 145 mm
Mass
: 0.8 kg (1.8 lbs)
SP-XSDVB10
Type
: Full range bass-reflex type
Speaker
: 8 cm (3-3/16 in.) cone × 1
Full range
Power Handling Capacity
: 30 W
: 16 Ω
Impedance
Frequency Range
: 85 Hz – 20 000 Hz
Sound Pressure Level
: 83 dB/W·m
Dimensions (W × H × D)
: 160 mm × 110 mm × 136 mm
Mass
: 0.55 kg (1.3 lbs)
Design and specifications subject to change without notice.
(Magnetically-shielded type)
(9-11/16 in. × 4-3/8 in. × 5-3/4 in.)
(6-5/16 in. × 4-3/8 in. × 5-3/8 in.)

Hide quick links:

Advertisement

Table of Contents
loading

Table of Contents