Installation; Installation Location; Secure The Appliance - Junkers SUPRAECO W HP 270 Installation And Operating Instructions Manual

Installation

Fig. 9
Manual transport
NOTICE: Damage from straps!
B Remove front casing (
B Make sure that the straps do not scratch or make
indentations on the surface of the appliance.
B Do not fasten the straps at the resistor (
[17]) or at the temperature sensor aperture (
Fig. 3, [4]).
To bring the appliance into position at the installation location, place
straps around the storage tank.
5 Installation
B Installation must only be carried out by an authorised contractor.
B The heat pump installation must follow the applicable regulations.
B Check that all pipe connections are intact and have not shaken loose
during transportation.
B Check the colour of the "tilt label" on the rear side of the appliance's
packaging. If the label is blue, the appliance cannot be installed and
should be returned on it's original packaging.
5.1

Installation location

Please note the following when choosing the installation location:
• The appliance must be installed in a dry, frost-free room. Optimum
appliance performance is achieved at room temperatures between
+5 °C and +35 °C.
• Check that the appliance's installation area has the required
resistance and alignment.
• The air outlet and air inlet must not be in locations where there is a risk
of explosion from gas, steam or dust.
• If open flue gas appliances are already installed at the installation
location, the appliance may not be operated with room air circulation.
Use of an inlet pipe for fresh air or another facility ensuring that the
inlet air is separate from the gas appliance is mandatory.
• Ensure that condensate drains correctly.
14
6720646160-45.1V
Fig. 3, [24]).
Fig. 3,
• The plinth of the appliance must be strong enough (the appliance
weighs about 400 kg when the storage tank is filled, with the weight
distributed equally over its 3 adjustable feet).
To ensure faultless operation and easy access to all components and
connections for maintenance and repairs, maintain the minimum
clearances specified in Fig. 10.
5 0 0
Fig. 10 Recommended minimum clearances (mm)
5.2

Secure the appliance

B Check the colour of the tilt label.
If it is not blue in the top arrow, remove the shrink wrap and external
protective packaging.
TELL
BLUE BEDS IN
ARROW INDICATES
COUNTAINER WAS
TIPPED OR
MISHANDLED
Transport Control Int´l Gmbh
Am Knick 9,22113 Oststeinbek
Tel: 0049 40 713 84 02
Fax: 0049 40 713 24 94
TELL
BLUE BEDS IN
ARROW INDICATES
COUNTAINER WAS
TIPPED OR
MISHANDLED
Transport Control Int´l Gmbh
Am Knick 9,22113 Oststeinbek
Tel: 0049 40 713 84 02
Fax: 0049 40 713 24 94
Fig. 11
B Lift the appliance from its pallet.
B To correctly align the appliance at the installation location, adjust the
height of the adjustable feet.
To ensure that the system operates faultlessly and the
condensate drains, the appliance must be aligned
vertically. The appliance must not tilt more than 1°,
preferably in the direction of the condensate drain.
NOTICE: Damage in the external casing!
B Do not tilt the appliance more than 20°.
4 3 0
4 0 0
6720645393-04.2V
ARRO BLUE
TIPPE COUN BEDS INDIC TAINE W IN TE LL
MISHA NDLE D OR ATES R WAS LL TE
D IN
R BEDS INDIC ATES WAS
ARRO TAINE W BLUE D OR NDLE D
COUN TIPPE MISHA
Tran
Am spor Knic t Con Gmb ek h
Fax: Tel: k 9,22 0049 trol 113 trol Int´l 84 Osts teinb 94 02
0049 40 40 Osts 713 Int´l Gmb 9,22 t Con 40 113 713 713 24
713 teinb 84 24 94 02 ek h Tran spor Knic k 0049 0049 40
Am Tel: Fax:
6720646160-46.1V
SUPRAECO W – 6 720 646 161 (2012/04)