Hisense K660HK3D series User Manual page 12

Remote Control
Indicator description
The remote control has three kinds of state indicating
lamp: power indicator light (blue), the power indicator light
(red), the code matching indicating lamp.
Power indicator light (blue): in TV remote control, the
remote control¡ ¯ s power indicator light (blue) will be
shining, when it is standby or the battery is removed, the
indicator lamp will be off.
Power indicator light (red): while charging, the light will be
on continuously, and if there is electricity shortage, it will
be shining.
Code matching indicator: in the code matching, the code
matching indicator light will be shining.
NOTE
In the corresponding mode, the corresponding indication
light will be shining. After entering the standby state, all
lights will be ex t inguished.
Code matching
While using the remote control for the first time, there
is need to carry out the operation of the code matching.
When the TV is on, make the remote control near the area
within 5cm below the code matching portion of the TV,
press and hold the " # " key on the remote control for more
than 3 seconds, the remote control¡ ¯ s power indicator (blue)
will begin fast shiny (please release the " # " key, keep the
remote control in the area of code matching), the remote
control¡ ¯ s power indicator (blue) and the code matching
indicator will be slowly flashing for three times, which
indicates that the operation is successful.
After the success of code matching, the remote control
will be back to the initial state of power.
If the matching is not successful, the remote control¡ ¯ s
indicator light will be returned to normal shining, please
repeat the operation again for re-matching the code.
This machine can simultaneously support two remote
control devices, the remote control matching the code
for the first time is the main remote control; and the one
doe second code matching is the aux i liary remote control,
please use the " * " key for code matching operation.
NOTE
¡ ¤
The remote control¡ ¯ s initial code matching will generally
be completed by the service personnel when they get to
your home for installing the TV set.
¡ ¤
If the remote control encounters an unknown error, the
receiver¡ ¯ s signal may probably be disturbed, at this time,
please remove the interference, and conduct the code
matching.
¡ ¤
In the standby mode, it will not support the code matching
for the time being.
Key pressing
After the code matching is completed, press the remote
control¡ ¯ s keys for the corresponding operation. In the key
operation, the power indicator light (blue) will be shining.
G e t t i n g S t a r t e d
Standby description
When the remote control device is in a quiescent state, it
will automatically enter a state of dormancy. After entering
a state of dormancy, the light will be shut off, press any
key to wake up the operation, after waking up, it will be
back to the state before the standby state.
Air mouse
For the convenience of the user operation, the remote
support supports the air mouse function.
Switch on the air mouse: shake the remote control gently
to activate the air mouse. At this point, you can hold the
remote control with one hand in the vertical direction,
through the wrist movement, you can control the mouse.
Switch off the air mouse: press any direction key (up,
down, left and right), you can stop the function.
If the air mouse appears to drift phenomenon, please
place the remote control statically to the standby state,
then reuse it.
NOTE
¡ ¤
When the air mouse is in the running state, press the OK
key with the left mouse button to achieve single-clicking
operation.
¡ ¤
In the home page operation and browsing the webpage,
you can use air mouse, and part of the interfaces and
applications cannot be supported temporarily.
OFN
The remote control has OFN (touch panel), it is available
for the fingers to slide the touch panel to control the
television.
You can achieve leftward sliding and rightward sliding
on the OFN, and the TV screen will produce the
corresponding sliding effect to achieve fast screen cutting
NOTE
¡ ¤
Some application programs cannot support the sliding
operation .
¡ ¤
When using OFN, please keep fingers dry, once it is wet,
it may affect its sensitivity.
Others
As the wireless device, the remote control device and
receiver¡ ¯ s signal may be under interference and shielding;
the wireless card inserted in the USB port may interfere
with the normal work of receiver; and the television wall
may lead to attenuation of receiver¡ ¯ s signal.
When the battery is normal in electric quantity, if the
remote control encounters an unknown error, the user
can insert the reset hole at the bottom of back of remote
control with a needle-shaped object and press for 1 ~ 2
seconds, the remote control can work normally.
|
7
G e t t i n g S t a r t e d U S E R M A N U A L
.