Table of Contents
Advertisement
Empyre Elite
Warranty service may only be performed by Pro-Fab Industries
or a Pro-Fab Authorized Empyre Elite Furnace Dealer or a Pro-
Fab Authorized Empyre Elite Furnace Service Centre.
PRO-FAB INDUSTRIES INC. WARRANTY
Pro-Fab Industries Inc. (hereinafter called "Pro-Fab") warrants to
the original owner of the Empyre Elite Furnace (hereinafter called
the "Empyre Elite") the following:
A two (2) year warranty on the workmanship of the furnace and
workmanship on all parts manufactured by Pro-Fab, from the
consumer date of purchase, and excluding normal wear items
such as (but not limited to) the door gasket, fire brick, insulation,
refractory, exterior finish.
A one (1) year warranty for any labour required for any repair or
replacement of the furnace or parts from the consumer date of
purchase based on Pro-Fab's predetermined labour rates and
allowable hours.
A limited pro-rated warranty coverage (which includes the one
(1) year labour coverage at Pro-Fab rates and hours as stated
above) for a defective firebox and water jacket only, based on the
following pro-rated scale from the consumer date of purchase:
• Years one (1) and two (2) – one hundred percent (100%)
coverage;
• Years three (3), four (4) and five (5) – sixty percent (60%)
coverage;
• Years six (6) and seven (7) – thirty percent (30%) coverage;
• Years eight (8) and nine (9) – fifteen percent (15%) coverage;
• Year ten (10) – ten percent (10%) coverage.
Absolutely no warranty is provided after ten (10) years from the
consumer date of purchase.
Note: All parts NOT manufactured by Pro-Fab carry their own
manufacturer's warranty. The owner is responsible for all related
Pro-Fab will not be responsible or liable for any of the follow-
ing: a) If warranty work requires removal or replacement of all
or a part of the furnace, Pro-Fab is not responsible for the cost
of plumbing, freight, permits, removal or disposal of damaged
furnace or parts, replacement of water or additives, labour after
the one (1) year warranty coverage expires, or any cost other
than the warrantied replacement part itself or the furnace; b)
The care, maintenance and safe operation of the Empyre Elite
Furnace which is the responsibility of the owner of the furnace;
c) Any accidents, injury, damage or loss incurred due to a heat-
ing system failure; d) Any accidents, injury, damage or loss in-
curred due to faulty installation, operation or maintenance; e)
Any cost incurred for replacing or repairing of parts not manu-
factured by Pro-Fab which carry their own manufacturer's war-
ranty; f) Any out-of-pocket expenses, alternative accommoda-
tions or loss of revenue due to defective parts or furnace; g)
Performance problems caused by improper sizing of the fur-
nace, vent connection, or air openings; h) Damages, malfunc-
There are no other warranties, expressed or implied, by Pro-
Fab or its Authorized Empyre Elite Furnace Dealers or Au-
thorized Empyre Elite Furnace Service Centres regarding the
Empyre Elite Furnace except the warranty expressed herein.
ANY IMPLIED WARRANTIES, INCLUDING MERCHANTABIL-
ITY, OR FITNESS FOR A PARTICULAR PURPOSE, SHALL NOT
EXTEND BEYOND THE APPLICABLE WARRANTY PERIODS
SPECIFIED ABOVE. PRO-FAB'S SOLE LIABILITY, WITH RE-
SPECT TO ANY DEFECT, SHALL BE AS SET FORTH IN THIS
LIMITED WARRANTY, AND ANY CLAIMS FOR INCIDENTAL OR
CONSEQUENTIAL DAMAGES ARE EXCLUDED.
Issue Date: February 2012 Part No. 817941R02
Model 100 and 200
10 YEAR LIMITED WARRANTY
costs necessary to replace those parts, unless covered by the
applicable manufacturer.
The above warranties are based on the following factors:
Pro-Fab reserves the right to repair or replace at its discretion
any defective part or furnace, in whole or in part.
Use of Pro-Fab approved water treatment. IMPORTANT: Pro-
Fab approved water treatment is available from your local dealer
or service centre and must be used and validated for warranty
coverage. The pH balance must remain between 8.8 and 11.0, the
nitrite level must remain between 730 and 1460 ppm as NaNO2,
and conductivity must be less than or equal to 4000 mmhos. A
copy of the invoice itemizing the purchase of approved water
treatment will be required as proof of maintenance in the event
of a warranty claim. All laboratory reports must be kept as proof
of maintenance (see page 19 of the Installation and Operation
Instruction Manual).
All instructions within the Installation and Operation Manual, as
well as all local/provincial/state and national codes have been
adhered to with respect to the chimney size and installation.
The water temperature has not dropped below 150°F (66°C)
during operation.
All instructions within the Installation and Operation Manual, as
well as all local/provincial/state and national codes have been
adhered to with respect to the minimum clearance to combustibles
and use of a non-combustible liner on a combustible floor per
the guidelines within this manual.
All instructions in the Empyre Elite Installation and Operation
Instruction Manual have been followed.
The Warranty Registration and a copy of the original bill (invoice)
must be forwarded to Pro-Fab within thirty (30) days of the date
of purchase to validate the warranty.
tions or failures resulting from the use of any attachment not
authorized by Pro-Fab; i) Units installed outside the continental
United States, Alaska, or Canada without prior approval from
Pro-Fab; j) Units with their safety certification labels removed;
or k) Damages, malfunctions or failures caused by force ma-
jeure, abuse, accident, fire, or acts of God.
Any available warranty will be void if: a) Maintenance proce-
dures are not followed (see Installation and Operation Instruc-
tion Manual page 19); b) Water treatment and proper additives
are not used as specified in the Installation and Operation In-
struction Manual (see page 19); c) The Empyre Elite Furnace
has been altered in any way; d) Any material other than Pro-Fab
approved fuel has been used; e) Any instruction given in the In-
stallation and Operation Instruction Manual which has not been
followed including during installation or regular maintenance;
or f) Any claim made under the warranty for a person other than
the original owner.
No person is authorized to bind Pro-Fab to any other warranty
whatsoever. Pro-Fab reserves the right at any time to make chang-
es or improvements to the design, materials or specifications of
the Empyre Elite line of furnaces or parts without thereby becom-
ing liable to make similar changes in the furnaces or any of its
parts previously manufactured.
Manufactured by:
Pro-Fab Industries Inc.
Box 112, Arborg, MB R0C 0A0
Printed in Canada JW0212
Advertisement
Table of Contents
