NAPCO XP-400 Using Instructions
Express series
Hide thumbs
Also See for XP-400:
- Installation instructions manual (28 pages) ,
- Using instruction (16 pages) ,
- Programming instructions manual (13 pages)
Related Manuals for NAPCO XP-400
Summary of Contents for NAPCO XP-400
- Page 1 ARMED READY ü SYSTEM Using Your ZONE 1 XP-400 ZONE 2 ZONE 3 ZONE 4 Security System NAPCO...
- Page 3 Introduction Congratulations on your purchase of an advanced NAPCO EXPRESS XP-400 Security System. Meticulously developed by a leading manufacturer of state-of-the-art security products, this system will provide you with unprecedented peace-of-mind & incorporates some of the most sophisticated features available today. Above all, it has been designed an extra step, to provide all those operating it with very easy, intuitive use.
-
Page 4: Table Of Contents
Introduction Table of Contents System Information Keypad Controls and Indicators ........ Arming your System (When Leaving) ....... Central Station Phone Number: ____________________ Bypassing Zones ............. Protecting Yourself While Home ....... Central Station Account Number: ____________________ Emergency Keys ............Disarming the System ..........For Service Call: ____________________ Silencing an Alarm............. -
Page 5: Keypad Controls And Indicators
Arm system. ZONE 4 Zone Lights (1 through 4) will light to indicate that the corresponding Zone is open, and will flash to indicate a zone in alarm. NAPCO Emergency Keys Press simultaneously to signal an emergency condition. Press ü... -
Page 6: Arming Your System When Leaving
Arming Your System Arming Your System When Leaving Before arming your system, make sure the Green Ready light is ON. This indicates that all of your prot- ective zones are secure. If any zones are open, the corresponding Zone light will be ON. Secure these zones before proceeding. -
Page 7: Protecting Yourself While Home
Arming Your System Protecting Yourself While at Home Before arming your system, make sure the Green Ready light is ON. This indicates that all of your protective zones are secure. If any zones are open, the corresponding Zone light will be ON. Secure those zones before proceeding. -
Page 8: Emergency Keys
Emergency Conditions Emergency Buttons Auxiliary The two sets of emergency buttons, if programmed, are always active whether the system is armed Emergency or disarmed. Discuss these buttons with your installer. The emergency signal will only be activated Enabled? when the two respective buttons are pressed at the same time. Auxiliary Alarm: Simultaneously press to alert the central station of an auxiliary... -
Page 9: Disarming The System
Disarming Your System / Silencing an Alarm Disarming Your System when Returning Enter your premises through the Entry/Exit door. The keypad will sound a steady tone to remind you to disarm the system before your Entry Delay time expires. ARMED Enter your user code. -
Page 10: Special Functions
2 seconds. This will also initiate a test of your codes. (see Programming user codes, page 14) battery to make sure it is adequately charged. The XP-400 Kepad Sounder On / Off also performs an automatic battery test very 24 hours... -
Page 11: Programming User Codes
Programming User Codes Your Installer has assigned a User 1 Code which may be used to not only Arm and Disarm the system, but also to enter the User Program Mode, where you can program and/or reprogram up to 4 User Codes. The following explains how you will use this code to program or erase additional user codes. -
Page 12: System Troubles
ü ü System Troubles The XP400 is constantly monitoring its own components, as well as all critical services, such as AC Power and the Telephone line, to insure that it is always ready to provide the protection for which it was designed. When a system trouble does occur, it will caution you by lighting the Yellow ü... - Page 13 ü ü System Troubles Keypad Beeps or Zone light System Trouble Action ü ü Condition SYSTEM Flashes 2 Beeps Bell / Siren Trouble There is a problem with the Bell or Siren. Call installing com- ARMED pany for service. READY 2 Beeps Wireless Receiver A problem has been detected with the wireless receiver.
- Page 14 Glossary and then the zone number to bypass a premises.(Press while armed) Ambush Code - In the event that zone. you are forced by an intruder to dis- arm your system, this special code Keypad Sounder - A local warning can be used to disarm the system, Central Station - Monitors alarm,...
- Page 15 Notes...
-
Page 16: Napco Limited Warranty
In no event shall NAPCO be liable for an amount in excess of NAPCO's original selling price of the product, for any loss or damage, whether direct, indirect, incidental, consequential, or otherwise arising out of any This warranty shall not apply to any equipment, or any part thereof, which has been repaired by others, failure of the product.