Do you have a question about the Silver RS and is the answer not in the manual?
Questions and answers
Biss
March 24, 2025
There is hardly any sound from one rs8 speaker
1 comments:
Mr. Anderson
March 24, 2025
There could be several reasons why there is hardly any sound from one Monitor Audio Silver RS8 speaker:
1. Connection Issue: Check if the speaker wires are properly connected to both the speaker and the amplifier/receiver. Loose or incorrect wiring can cause sound issues.
2. Amplifier/Receiver Settings: Ensure that the amplifier or AV receiver settings are correct and that the affected speaker is not muted or set to a very low volume.
3. Speaker Damage: Inspect the speaker for any visible damage, such as a torn driver or disconnected internal wiring.
4. Port Blockage: The RS8 has both front and rear ports. If a port is blocked improperly, it could affect sound output.
5. Balance and Output Settings: Check the balance settings on your audio system to ensure the signal is evenly distributed between both speakers.
6. Testing with Another Source: Try connecting the speaker to a different amplifier or audio source to determine if the issue is with the speaker or the original system.
If none of these steps resolve the issue, the speaker may require professional servicing under the warranty.
‘music’ production, or as we say at Monitor Audio our aim is to make the music experience “As close as it gets”. Please read through this manual to familiarize yourself with any safety advice and how best to set up your speakers to achieve the very best listening experience.
Cleaning Great care and attention has gone into the materials chosen to produce the Silver RS loudspeakers. It is our intention that they should provide a lifetime of musical pleasure. A gentle wipe with a dry, clean cloth is all that is required to remove any dust. Treat them as you would a fine piece of furniture because that is how they have been designed.
Your Silver RS1 Don't be fooled by the size. The most compact loudspeaker of the Silver RS range delivers a sound that's anything but small, rivalling far more costly 'compact monitors' for bass extension, mid-range resolution and precise imaging within a stunningly open soundstage. Allied with ‘figure 8’ cross- bracing to reduce cabinet resonance an excellent stand mount loudspeaker has been created.
Your Silver RS5 The new Silver RS5 is the smallest floor stander in the new Silver RS Series, and the classically simple two-way layout ensures a beautifully clean appearance. It’s slim cabinet design and resulting small footprint ensue versatility for any environment.
Your Silver RS LCR The Silver RS LCR is the vital aesthetic and sonic link in any Silver RS home cinema or multi-channel music system, bringing extra solidity, depth and realism to the front soundstage, especially with dialogue. It can be used as a centre speaker or as a traditional left or right speaker when placed upright.
180-degree dispersion characteristics. Whilst the bass driver always operates in phase, the tweeter section can be configured to operate as a bi-pole or di-pole, which means the Silver RS FX, can just as easily be used on sidewalls in a more advanced 7.1 system.
Connecting your Silver RS FX The Silver RS FX’s are supplied as right hand or left hand units and both can be configured to either bi-pole or di-pole. The factory setting is bi-pole as illustrated in fig. 1 below. In bi-pole mode, all speaker units (mid/bass unit and tweeters) are in phase.
Spiked Foot Fixing For Carpeted Floors (Silver RS5, RS6 & RS8 only) The amazingly engineered composite Silver RS spiked foot encorporates a spike for use on carpeted floors and also, a soft polymer pad (for use on wooden or tiled floors).
These can be simply removed by placing a thin, flat object underneath them and carefully levering them free. All of the Silver RS Series loudspeakers (except the RS FX, see page 9) can be either single or bi-wired/bi-amp. Monitor Audio always recommends bi-wiring your loudspeakers for improved sound quality.
The equipment should be returned in its original packaging to the original supplier where possible, or to any other authorised Monitor Audio dealer. If it is not possible to return the equipment by hand, then it should be sent carriage prepaid via a reputable carrier.
Data Protection We at Monitor Audio are committed to respecting the wishes and privacy of our customers. Any information you provide will be held in the strictest confidence and only used within the Monitor Audio organisation for the provision of services such as warranty claims or spare parts.
Need help?
Do you have a question about the Silver RS and is the answer not in the manual?
Questions and answers
There is hardly any sound from one rs8 speaker
There could be several reasons why there is hardly any sound from one Monitor Audio Silver RS8 speaker:
1. Connection Issue: Check if the speaker wires are properly connected to both the speaker and the amplifier/receiver. Loose or incorrect wiring can cause sound issues.
2. Amplifier/Receiver Settings: Ensure that the amplifier or AV receiver settings are correct and that the affected speaker is not muted or set to a very low volume.
3. Speaker Damage: Inspect the speaker for any visible damage, such as a torn driver or disconnected internal wiring.
4. Port Blockage: The RS8 has both front and rear ports. If a port is blocked improperly, it could affect sound output.
5. Balance and Output Settings: Check the balance settings on your audio system to ensure the signal is evenly distributed between both speakers.
6. Testing with Another Source: Try connecting the speaker to a different amplifier or audio source to determine if the issue is with the speaker or the original system.
If none of these steps resolve the issue, the speaker may require professional servicing under the warranty.
This answer is automatically generated