Table of Contents
Advertisement
Glass Media Installation
Glass Media Kits (one required)
Cat. No.
Model
H8412
CRSHGL-RBLK
H8424
CRSHGL-RBLU
H8413
CRSHGL-P
H8538
CRSHGL-GF
H8539
CRSHGL-C
WARNING
• HANDLE MEDIA ONLY WHEN COOL. Turn OFF
all electricity to the appliance before installing
media. Media gets very HOT during fireplace use
and will remain hot up to one hour after the gas
supply is turned off.
• Any attempt to use media not specified for your
fireplace configuration will result in incomplete
combustion, sooting, and poor flame quality, and
will void the warranty.
1. Fill the provided measuring box level with the top (approximately 3
cups).
2. Distribute the measured amount of media in an even layer in the
recessed area on top of the burner (shaded area in Figure 14).
IMPORTANT!
• Do NOT mound up media.
• If using multiple colors of media, NEVER use more than one level
measuring box (approximately 3 cups) total at one time.
• If media is not installed according to the media installation instruc-
tions, flame impingement and improper combustion could occur
and result in soot and/or excessive production of carbon monoxide
(CO), a colorless, odorless, toxic gas.
Figure 14 - Media Installed
Description
Glass Media, 5LB Bag, Reflective Black
Glass Media, 5LB Bag, Reflective Blue
Glass Media, 5LB Bag, Platinum
Glass Media, 5LB Bag, Goldfinger
Glass Media, 5LB Bag, Copper
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
Surround Installation
The fireplace insert surround panels are made of heavy gage steel for
durability and, if desired, for the ease of making an inside fit in the fire-
place. See Packaging List for available sizes.
1. Remove the speed nuts (A in Figure 15) from the parts bag and install
(with the flat surface forward) on the six holes in the surround brack-
ets - three on each side of the insert (B in Figure 15). A flat bladed
screwdriver may help in installing the nuts.
2. Install all surround panels and trim with the appliance positioned in
the fireplace, but a few inches in front of its final location.
3. If an Arch face is to be installed on the appliance, the sight obstructor
that comes with the face must be installed prior to installing the sur-
round panels. See the instructions included with the face for proper
sight obstructor installation.
4. Install the side surround panels by lining up the holes in the tabs on
the side surround panels in front of the holes on the surround brackets.
Next insert two slotted 1/4" truss screws for each side surround panel
and secure loosely.
5. Fasten the top surround panel with the remaining two truss screws.
Tighten all six truss screws after adjusting the surround panels to
eliminate space between side and top surround panels.
6. Assemble the surround trim by inserting the elbowed retainer in the
rectangular slot in the ends of the longest piece of trim and secure by
tightening the screw in the retainer. Slide the mitred ends of the two
side trim pieces onto the elbowed retainer and secure by tightening
the retainer screw.
7. The fastened trim pieces should now be horseshoe shaped. Slide the
trim down over the surround panels so the edge of the surround panel
fits just behind the rounded edge of the trim.
8. Install three spring clips (found in parts bag in firebox) in each piece
of trim by inserting them between the rear of the surround and the
channel of the trim. The spring clips will push the trim tight to the
surround.
B
A = Speed nuts
B = Holes in the surround brackets - three on each side
Figure 15
C = Location where hooked brackets on face will hang
Face Installation
A number of different face finishes and styles are available for your
appliance. The Arch face comes with a sight obstructor that must be
installed prior to installing the surround panels and face. Instructions
for installing the sight obstructor are included with the face. The faces
come with hooked brackets. To install the face, hang the hooked brackets
on the surround brackets (See C in Figure 15).
Note: Plated surfaces must be cleaned with glass cleaner and a soft clean
cloth before firing the first time or fingerprints and stains will remain
permanently. NEVER use brass polish to clean plated surfaces, this
will remove the plating!!!
A
C
Latches
B
15
Advertisement
Table of Contents
