Table of Contents
Advertisement
Portable Gas Barbecues
Operating and assembly instructions
GT3-V
GTI4S Island
FOR YOUR SAFETY
IF YOU SMELL GAS
1.Shut off gas to the appliance,
if possible.
2.Extinguish any open flame.
3.Open hood.
4.If odour continues,
immediately call your gas
supplier or fire department.
GT4-S
GTI4SB-S Island
FOR YOUR SAFETY
1.Do not store or use
petrol or other flammable
vapours and liquids in the
vicinity of this or any other
appliance.
2.A gas cylinder not connected
for use must not be stored
in the vicinity of this or any
other appliance.
GT4S-V/GT4S
These instructions are a
guide to assembling and
using the
GT3-V,GT4-S,GT4S
GT4S-V, GT4SB-S , GTI4SB-S ,
GTI4S,GTI5SB-S
Please read carefully, and
retain for future reference.
Only to be used outdoors.
Illustration may vary from barbecue
cantained in carton.
GT4SB-S
GTI5SB-S Island
barbecue.
Advertisement
Table of Contents
Related Manuals for Rinnai GT3-V
Summary of Contents for Rinnai GT3-V
- Page 1 Portable Gas Barbecues Operating and assembly instructions GT3-V GT4S-V/GT4S GT4-S GT4SB-S GTI4S Island GTI5SB-S Island GTI4SB-S Island These instructions are a FOR YOUR SAFETY FOR YOUR SAFETY guide to assembling and 1.Do not store or use IF YOU SMELL GAS...
- Page 2 GT4S-V/GT5S-V/GT5SB-S GTI4S/GTI5S/GTI5SB-S...
- Page 4 be properly converted from the factory built LP. Contact...
- Page 6 AGA certificate #7748 Input Mj/h Jet mm(Hi/Low) Input Mj/h Jet mm(Hi/Low)
- Page 7 2 . DO NOT TIGHTEN BOLTS UNTIL ALL FITTINGS ARE IN POSITION,UNLESS SPECIFIED. 3. Model GT4SB-S Shown as example . Install Trolley Side Panels onto Trolley Bottom Panel Phillips Head Screw 1/4"x1/2" Qty.4 Part # S112G0408A (GT3-V/GT4S/GT4S-V) Part # S112G04081 (GT4-S/GT4SB-S) Install Casters and wheels Phillips Head Wheel Bolt 3/8"x2-15/16" Qty.2...
- Page 8 Install Trolley Separation Panel Phillips Head Screw 3/16"x3/8" Qty.4 Part # S112G0306A (GT3-V/GT4S/GT4S-V) Part # S112G03061 (GT4-S/GT4SB-S) Flange Nut 3/16" Qty.4 (GT3-V/GT4S/GT4S-V) Part # S312G0306A Part # S312G03061 (GT4-S/GT4SB-S) Install Door Stop Plate Countersunk Flat Head Screw 3/16"x3/8" Qty.2 Part # S142G0306A...
- Page 9 - Locate the screw head into the keyholes on the top face of the trolly side panels,slide back to lock into posilion,tighten screws. Phillips Head Screw 1/4"x1/2" Qty.4 Part # S112G0408A (GT3-V/GT4S/GT4S-V) Part # S112G04081 (GT4-S/GT4SB-S) Fig.1 Install Separation Panel Bracket Phillips Head Screw 3/16"x3/8"...
- Page 10 Install Side Shelf Brackets (GT3-V/GT4-S ) Install the Side Shelf Brackets onto the Bowl Side Panels. Align the holes on the Bracket and the holes on the Bowl Side Panel, insert the 4 Phillips Head Screws 3/16"x3/8" and 4 Phillips Head Screws 1/4"x1/2" and tighten securely.
- Page 11 10 . Install Grease Tray Refer to page 28 for "Maintenance/Cleaning The Grease Tray" Connect Side Burner Hose 12 . Install Gas Cylindes refer to page 13 for more information - Finger tighten connection before using Spanner to prevent crossthreading - Do Not use thread sealing tape or similar products.
- Page 12 GTI4S/GTI5S/GTI5SB-S ISLAND CAUTION : To assemble this grill, you should obtain assistance from another person when handling some of the larger and heavier pieces. * M odel GTI5SB-S shown for example. Assemble Left Cabinet Panels Phillips Head Screw 3/16"x3/8" Qty. 6 (GTI4S) Front Part # S112G03064...
- Page 13 Install Level Adjusters and Door Hinge Bracket onto Left Cabinet Bottom Shelf Countersunk Flat Head Screw 3/16"x1/4" Qty. 2 (GTI4S) Part # S142G03044 (GTI4SB-S/GTI5SB-S) Part # S142G03041 Install Storage Shelf onto Left Cabinet Install 2 Bolts B onto the Left and Right Pane , rear and tighten securely using 2 Flange Nuts 3/16".
- Page 14 Install Front Bracket, Bowl Support Bracket and Left Side Shelf onto Left Cabinet Phillips Head Screw 3/16"x3/8" Qty. 2 Flange Nut (GTI4S) 3/16" Part # S112G03064 (GTI4SB-S/GTI5SB-S) Part # S112G03061 Flange Nut 3/16" Qty. 2 (GTI4S) Part # S312G03064 (GTI4SB-S/GTI5SB-S) Part # S312G03061 Fig.1 Phillips Head Screw...
- Page 15 Assembly Right Cabinet Panels Phillips Head Screw 3/16"x3/8" Qty. 6 (GTI4S) Part # S112G03064 (GTI4SB-S/GTI5SB-S) Part # S112G03061 Flange Nut 3/16" Qty. 6 (GTI4S) Part # S312G03064 (GTI4SB-S/GTI5SB-S) Part # S312G03061 Install Right Cabinet Bottom Shelf Phillips Head Screw 1/4"x3/8" Qty.
- Page 16 Install Level Adjusters, Door Hinge Bracket and Storage Shelf onto Right Cabinet Install Level Adjusters onto the bottom of the Right Cabinet and tighten securely by Hand. Install Door Hinge Bracket onto the Bottom Shelf using 2 Countersunk Flat Head Screws and tighten securely.
- Page 17 Install Right Cabinet Separation Panel Bracket Phillips Head Screw 3/16"x3/8" Qty. (GTI4S) Part # S112G03064 (GTI4SB-S/GTI5SB-S) Part # S112G03061 Install Partition Panel and adjust Level adjusters Align the holes on the Partition Panel with the holes on the Left and Right Cabinet Panles. Install 4 Phillips Head Screws 1/4"x3/8"...
- Page 18 Install Barbecue Head Remove all componets from the Grill Bowl. Install 4 Phillips Head Screws to the bottom of the Grill Bowl. Tighten the Screws only half way. With the help of your assistant, lift and position the head into the holes on the Bowl Support Brackets, then slide to front (as shown in Fig.1) and tighten all screws.
- Page 19 Install Doors Place the Door Assembly into the Upper door bracket, Press the spring lever mechani sm at the bottom of the door and position over the lower door bracket opening. Release the spring lever to lock the Door into the Door Lower Bracket.
- Page 20 Install Grease Tray Pull out the Grease Tray Bracket. Place the Grease Tray into the Grease Tray Bracket as shown. Push the Grease Tray Bracket back into position. Refer to page 28 for "Maintenance/Cleaning The Grease Tray" Install Gas Cylindes refer to page 13 for more information After connection of the side burner hose and the gas cylinder do not operate the...
-
Page 21: A S S E M B L Y - G E N E R A L
A S S E M B L Y – G E N E R A L Install Ignitor Battery Familiarise yourself with the general information and Remove Ignitor Cap from Control Panel. safety guidelines located at the front of this booklet. Place supplied AA battery into the Ignitor Check to see that gas cylinder is filled and that end of Slot with positive pole facing you. - Page 22 Spark Gap 4-5mm Spark Electrode Tip Spark Receiver...
- Page 23 Cooking Rack/Secondary Hook...
-
Page 24: Operation
MAIN BURNER IGNITION BACK BURNER IGNITION Open barbecue hood before attempting to light burners. NOTE: The location of the back burner makes it more susceptible to wind conditions that will Set burner control knobs to ‘OFF’ and open the decrease the performance of your rotisserie cooking. gas cylinder valve. -
Page 25: Operating Procedure
OPERATING PROCEDURE THE SIDE BURNER IS DESIGNED FOR USE WITH A WOK UP TO 360 mm DIAMETER AND COOKING POTS UP TO BURN-OFF 200 mm DIAMETER. Before cooking on your barbecue for the first time, burn-off any USE OF VERY LARGE POTS MAY RESULT residual oils or foreign matter from the cooking plates. -
Page 26: Safety Points
• The easiest foods to balance are those of uniform shape ROTISSERIE and texture. To test if the food is balanced correctly when secured, place the ends of the rotisserie skewer loosely Rotisserie is available as an optional extra from your place in the palm of your hands. - Page 27 IF THE BARBECUE FAILS TO LIGHT SHOULD A FLASHBACK FIRE OCCUR IN OR AROUND THE BURNER TUBES, FOLLOW THE INSTRUCTIONS BELOW. Turn gas off at source and turn burner control knobs to FAILURE TO COMPLY WITH THESE ‘OFF’. Wait at least five (5) minutes for gas to clear, then INSTRUCTIONS COULD RESULT IN A FIRE retry.
- Page 28 " " CONTENTS OF GREASE DRAINING TRAY MAY BE VERY HOT DURING COOKING. ALLOW TO COOL COMPLETELY BEFORE DISPOSING OF THE CONTENTS. AFTER CONTINUOUS USE, FAT AND/ OR COOKING JUICES MAY BUILD UP. TO AVOID ANY FLARE-UPS, IT IS RECOMMENDED THAT THE GREASE TRAY BE EMPTIED REGULARLY.
- Page 30 Orifice Gas Valve Assembly Burner Tube Foot Burner Port Burner Tube...
- Page 32 D I A G R A M GT3-V Model...
- Page 33 Model GT3-V DESCRIPTION Part No. Hood Assembly P0014637FB Temperature Gauge P00601484B P00213050M Hood Handle Hood Handle Seat -Left P00307061E Hood Handle Seat -Right P00308061E Hood Rubber Pad P05518002I Bowl Panel Set,Left P00761164A Bowl Panel Set,Right P00762154A Bowl Grease Shield P06901030B...
- Page 34 D I A G R A M...
- Page 35 Model GT4-S DESCRIPTION Part No. Hood Assembly P0014742E4 Temperature Gauge P00601484B P00213047M Hood Handle Hood Handle Seat -Left P00307061E Hood Handle Seat -Right P00308061E Hood Rubber Pad P05518002I Bowl Set P007139464 Door Guide P055101414 Bowl Grease Shield P069010304 Trolley Panel-Righ P076180524 Wheel Cap P05124002C...
- Page 36 D I A G R A M...
- Page 37 Model GT4S DESCRIPTION Part No. Hood Assembly P0014742E4 Temperature Gauge P00601484B P00213047M Hood Handle Hood Handle Seat -Left P00307061E Hood Handle Seat -Right P00308061E Hood Rubber Pad P05518002I Bowl Set P007139364 Door Guide P05510141K Bowl Grease Shield P069010304 Trolley Panel-Righ P07618052H Wheel Cap P05124002C...
- Page 38 D I A G R A M...
- Page 39 Model GT4S-V DESCRIPTION Part No. Hood Assembly P0014742FJ Temperature Gauge P00601484B P00213047M Hood Handle Hood Handle Seat -Left P00307061E Hood Handle Seat -Right P00308061E Hood Rubber Pad P05518002I Bowl Panel Set,Left P00761164A Bowl Panel Set,Right P00762154A Bowl Grease Shield P06901030B Trolley Panel-Righ P07618052H Wheel Cap...
- Page 40 D I A G R A M...
- Page 41 Model GT4SB-S DESCRIPTION Part No. Hood Assembly P0014742E4 Temperature Gauge P00601484B Hood Handle P00213047M1 Hood Handle Seat -Left P00307061E Hood Handle Seat -Right P00308061E Hood Rubber Pad P05518002I Bowl Set P007139364 Door Guide P055101414 Bowl Grease Shield P069010304 Trolley Panel-Right P076180524 Wheel Cap P05124002C...
- Page 42 D I A G R A M...
- Page 43 Model GTI4S ISLAND Part No. DESCRIPTION Hood Assembly P0014742FJ Temperature Gauge P00601474B Hood Handle P00213047M Hood Handle Seat-Left P00307061E Hood Handle Seat-Right P00308061E Hood Rubber Pad P05518002 I Bowl Panel,Left P00761194A Bowl Panel,Right P00762184A Bowl Grease Shield P06901030B Separation panel bracket-right P01001109L Right Cabinet -rear Panel...
- Page 44 D I A G R A M...
- Page 45 Model GTI4SB-S ISLAND Part No. DESCRIPTION Hood Assembly P0014742E4 Temperature Gauge P00601471B Hood Handle P00213047M Hood Handle Seat-Left P00307061E Hood Handle Seat-Right P00308061E Hood Rubber Pad P05518002 I Bowl Set P007139264 P010011084 Separation panel bracket-left Bowl Grease Shield P069010304 Separation panel bracket-right P010011094 Right Cabinet -rear Panel...
- Page 46 D I A G R A M...
- Page 47 Model GTI5SB-S ISLAND Part No. DESCRIPTION Hood Assembly P0014805E4 Temperature Gauge P00601471B Hood Handle P00213048M Hood Handle Seat-Left P00307061E Hood Handle Seat-Right P00308061E Hood Rubber Pad P05518002 I Bowl Set P007139264 P010011084 Separation panel bracket-left Bowl Grease Shield P069010304 Separation panel bracket-right P010011094 Right Cabinet -rear Panel...
- Page 48 RINNAI NEW ZEALAND. LTD 105 Pavilion Dr, Airport Oaks, Mangere Head Office: Manukau 2150. PO Box 53177, Airport Retail Centre Manukau 2150. Tel (09) 257 3800. Fax (09) 257 3899. info@rinnai.co.nz www.rinnai.co.nz For your local Service Centre 0800 RINNAI (0800 746624).
Need help?
Do you have a question about the GT3-V and is the answer not in the manual?
Questions and answers