Celestron NexStar GPS Instruction Manual page 16

sky, slews to an alignment star and asks you to position the star is in the center of the eyepiece. The NexStar is then ready to start
finding and tracking any of the objects in its 40,000+ object database. Before the telescope is ready to be aligned, it should be set
up in an outside location with all accessories (eyepiece, diagonal and finderscope) attached and lens cover removed as described
in the Assembly section of the manual. Before turning on the NexStar, make sure that the tube is pointed downward and both the
altitude and azimuth clutches are locked down. To begin the GPS alignment:
1. Power on the NexStar by flipping the switch located on the
bottom portion of the drive base, to the "on" position. Once
turned on the hand control display will say NexStar GPS
Press ENTER to choose GPS Align or use the UP/Down
scroll keys (10) to select a different mode of alignment.
Pressing the ALIGN key will bypass the other alignment
options and the scrolling text and automatically begins GPS
align.
2. Once GPS Align has been selected, the telescope will begin
to move to its north and level position. While the NexStar is
positioning itself, the GPS receiver automatically begins to
establish a link with the GPS satellites orbiting the Earth.
The hand control screen will display the message GPS
Searching to let you know that it is linking with the Searching Searching Searching
satellites.
3. Once the NexStar has established a link with the required
satellites, the hand control display will read
Linked Linked. Linked Linked
current time and position directly to your NexStar. The
NexStar now has all the necessary data to make a virtual
model of the sky, select two bright stars for alignment and
begin slewing to the first star.
4. When the NexStar has finished slewing to its first alignment
star, the hand control display will ask you to use the arrow
buttons to center the alignment star in the cross hairs of the
finderscope. At this point the telescope is only roughly
aligned, so the alignment star should only be close to the
field of view of the finderscope. Once centered in the
finderscope, press ENTER. If for some reason the chosen
star is not visible (perhaps behind a tree or building) you
can press the UNDO button to have the NexStar select and
slew to a different star.
5. If the finderscope has been properly aligned with the
telescope tube, the alignment star should now be visible
inside the field of view of the eyepiece. The NexStar will
ask that you center the bright alignment star in the center of
the eyepiece and press the ALIGN button. This will accept
the star as the first alignment position. (There is no need to
adjust the slewing rate of the motors after each alignment
step. The NexStar automatically selects the best slewing rate
for aligning objects in both the finderscope and the
eyepiece).
6. After the first alignment star has been recorded, the NexStar will automatically slew to a second alignment star and
have you repeat the alignment process for that star. When the telescope has been aligned to both stars, the display will
read "Alignment Successful" Alignment Successful" and you are now ready to find your first object. Alignment Successful" Alignment Successful"
Observing
T i p
T i p
For the best possible pointing accuracy, always center the alignment stars using the up arrow button and the right arrow button.
Approaching the star from this direction when looking through the eyepiece will eliminate much of the backlash between the
gears and assure the most accurate alignment possible.
NexStar GPS.
NexStar GPS NexStar GPS
The GPS satellites will then report the
A Few Words on GPS:
The NexStar GPS uses an on-board GPS to take
the guesswork out of aligning your telescope with
the sky. Once GPS Align is selected, the NexStar
automatically initiate the internal GPS module.
However, there are a few things you should be
aware of in order to get the full use of its many
capabilities:
GPS alignment will only work when the
telescope is set-up outdoors with an
unobstructed view of the sky.
NexStar is set-up in a location that has a
limited horizon in any direction, the GPS
alignment may still work, however it will
take much longer for the telescope to find
GPS GPS GPS GPS
and link with the needed satellites.
When using GPS alignment for the first
time, it may take 3-5 minutes for the
NexStar to link-up with its satellites.
Once the telescope is successfully linked,
leave the telescope powered on for at
least 20 minutes. During this time the
NexStar will download the complete
almanac of orbital elements (called the
ephemeris)
satellites.
received it will be stored for future
alignments.
If your NexStar is transported over a
long distance (say from the northern to
the southern hemisphere) it may take as
long as one hour to establish a satellite
link from its new location.
wishing to travel long distances with their
telescope are advised to begin the GPS
alignment in advance to allow the unit to
acquire the necessary data.
16
If the
for the orbiting GPS
Once this information is
Observers