Oki OKIPAGE 14i Maintenance Manual page 151

LCD display USER MNT
MENU
RESET
HEX DUMP
DRUM CNT
RESET
RSRC SAV
REC BUF
ECP
ENABLE *
OP MENU
ENABLE *
X ADJUST
0mm *
Y ADJUST
0mm *
2ND TRAY
5 *
PLACE PG
CENTER *
SETTING
0
JAMRCVR
ENABLE *
PWR SAVE
ENABLE *
Press the
MENU key.
INITIAL-
IZING
ON LINE
XXX
41356801TH Rev.1
Press the
After the completion
MENU key. Press the
of processing
ENTER key.
MENU
RESET'NG
(See Table4-1)
Press the
Press the
MENU key.
ENTER key.
ON-LINE
HEX DUMP
Press the
After the completion
MENU key. Press the
of processing
ENTER key.
DRUM CNT
RESET'NG
Press the
MENU key.
AUTO
Press the
Sets the size of area where, at switching either of PCL
OFF
or key.
and POSTSCRIPT to the counterpart, environment such as
200KB
permanent DLL and MACRO can be saved for the switched
400KB
part, and when it is returned, the saved environment can be
800KB
recalled.
1.2MB
Enable only when PS option + additional memory is connec-
1.8MB
ted and cable of obtaining 10% assignment to the size of ad-
2.4MB
ditional memory which is installed when this setting is selec-
ted.
8.4MB
9.8MB
11.2MB
AUTO
Press the
Setting of receiving buffer.
8KB
or key.
If you select a large value, the data transmitting time from
20KB
PC will be shortened, but Memory Overflow become easy
50KB
to happen.
Press the 100KB
MENU key. 1MB
Press the
A function to switch IEEE and 1284 parallel I/F ECP mode
ECP
or key.
Enable/Disable when level-2 menu Centronics I/F bi-
DISABLE
directional Centronics is set to Disable, this becomes invalid
regardless of the setting.
Press the
Writing into the EEPROM is performed after pressing the
or key.
OP MENU
ENTER key. Press the ON LINE key if you wish
DISABLE
to get out of this mode.
Press the
Press the
MENU key.
Writing into the EEPROM is performed after pressing the
or key.
ENTER key. Press the ON LINE key if you wish to get out of
X ADJUST
this mode.
+0.25mm
(Range of Adjustment: +2.00mm to -2.00mm; 0.25mm steps)
Press the
MENU key.
Press the
Writing into the EEPROM is performed after pressing the
or key.
X ADJUST ENTER key. Press the ON LINE key if you wish to get out of
+0.25mm this mode.
(Range of Adjustment: +2.00mm to -2.00mm; 0.25mm steps)
Press the
In the feeding destination selecting command (ESC&I#H) for
2ND TRAY
or key.
PCL5 Emulation, # designated for 2nd Tray is set.
1
As compared with mechanical setting position of paper being a
Press the
PLACE PG
center alignment, a printing image is moved in accordance with
ENTER key.
LEFT
the left alignment which is the same as HP (canon).
Press the
Enable only for PCL.
MENU key.
Press the
Used for fine adjustments when conspicuously scratchy printout results in certain
0 *
or key.
environment/special madia.
+ 1
Performs PQ adjustment when using special environment/special media continuosly.
+ 2
*
(Note1)
Incrememt when light specs or snow flake like printout occurs in high density print
- 1
areas.
- 2
Decrement when print results be come faded.
Press the
Specifies the Recovery Enable/Disable when an exit jam occurs.
JAMRCVR
or key.
• ENABLE : Guarantees Jam Recovery to allow the paper's bottom edge to pass
DISABLE *
• DISABLE : Increases the print performance for continuous printing that requires
Press the
A function to switch Power Save mode Enabel/Disable.
PWR SAVE
or key.
When DISABLE is selected, Power Save Level-2 menu will not appear.
DISABLE
ON-LINE
XXX
ON-LINE
XXX
OUT sensor as in normal usage.
large edit memory Demerit is, however, that this does not guarantee the Jam
Recovery after the paper's bottom edge passes WRITE sensor (after sending
print data to the drum (ID) is complete)
151 /