Table of Contents
Advertisement
Quick Links
English
Operating Instructions
Deutsch
Betriebsanleitung
Operating Instructions
Français
Notice d´utilisation
Italiano
Istruzioni sull´uso
Svensk
Bruksanvisning
Suomi
Käyttöohje
Español
Instrucciones de manejo
Nederlands
Gebruiksaanwijzing
Русский
Руководство по эксплуатации
MIRKA®
Random Orbital Sander
Random Orbital Sander
125 mm (5 in.) & 150 mm (6 in.)
125 mm (5 in.) & 150 mm (6 in.)
1-10
11-21
22-32
33-43
44-54
55-65
66-76
77-87
88-98
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for MIRKA Random Orbital Sander
Summary of Contents for MIRKA Random Orbital Sander
-
Page 1: Operating Instructions
MIRKA® Random Orbital Sander Random Orbital Sander 125 mm (5 in.) & 150 mm (6 in.) 125 mm (5 in.) & 150 mm (6 in.) English Operating Instructions 1-10 Deutsch Betriebsanleitung 11-21 Operating Instructions Français Notice d´utilisation 22-32 Italiano Istruzioni sull´uso... -
Page 2: Warranty
The warranty period commences at the date of purchase. The warranty only covers imputable material and manu- facturing defects. Parts replacement or repair during the warranty period is free of charge if carried out by an official KWH MIRKA service center. -
Page 3: Work Stations
Putting the Tool into Service Please Read and Comply with 1) General Industry Safety & Health Regulations, Part 1910, Use a clean lubricated air supply that will give a measured air OSHA 2206, available from: Superintendent of Documents; pressure at the tool of 6.2 bar (90 psig) bar when the tool is run- Government Printing Office;... - Page 4 Parts Page TO VACUUM SYSTEM FOR CENTRAL VAC INLET INLET TORQUE SETTING NOTE ITEM in.-lbs. (Nm) 55 - 65 (6.2 - 7.3) 16 - 20 (1.8 - 2.3) 60 - 72 (6.8 - 8.1) 36 - 48 (4.1 - 5.2) 30 - 35 (3.4 - 3.9) Original Instructions...
-
Page 5: Parts List
Parts List Item Description Qty. MPA0040 RETAINING RING MPA0021 BEARING MPB0017 REAR ENDPLATE MPA0005 CYLINDER ASSEMBLY MPA0042 O-RING MPB0005 ROTOR MPA0010 VANE MPA0041 MPB0016 FRONT ENDPLATE MPA0019 BEARING MPA0045 O-RING MPA0001 LOCK RING MPB0348 8 mm (5/16 in.) ORBIT AirSHIELD™ SHAFT BALANCER FOR 125 mm (5 in.) PADS MPB0334 8 mm (5/16 in.) ORBIT AirSHIELD™... - Page 6 KWH Mirka, Ltd. cannot be held responsible for the consequences of using declared values instead of actual exposure values for any individual risk assessment.
-
Page 7: Troubleshooting Guiide
Ring groove. Remove Motor Assembly and Re- Install the Motor Assembly. Motor Parts Worn Overhaul Motor. Contact authorized Mirka Service Center. Worn or broken Spindle Bearings Replace the worn or broken Bearings. Air leakage through the Speed... - Page 8 Mirka Italia s.r.l. www.mirka.com Italy Tel. +39 0733 207511 info@mirkaitalia.com www.mirkaitalia.com KWH Mirka Ibérica S.A.U. Spain Tel. +34 93 682 09 62 mirkaiberica@mirka.com KWH Mirka Mexicana S.A. de C.V. México Tel. +52 55 5148 3212 ventas.mx@mirka.com www.mirka.com.mx Quality from start to finish...
Need help?
Do you have a question about the Random Orbital Sander and is the answer not in the manual?
Questions and answers
best sander spped on resin surface with say p60 abrinet. hard resin and about 3 mm to remove to get level
The best sander speed for a MIRKA sander using P60 Abranet on a hard resin surface to remove about 3 mm for a level finish is speed 4.
This answer is automatically generated