Advertisement
Quick Links
Advertisement
Related Manuals for MotoSAT DataStorm D3
Summary of Contents for MotoSAT DataStorm D3
-
Page 2: Table Of Contents
User Guide Read Me 10/07/2005: Note that the DataStorm Administrator will NOT WORK with the current release of DataStorm D3 code [v3.7.8] 10/07/2005: Please refer to the D3 Changelog notes for more information on current known issues. Table of Contents... -
Page 8: Standard Functions
| Standard Functions DataStorm D2 System Status Page Cont. The system status page will be broken up into 3 sections: main, sensors, and satellite. | DataStorm D3 System Status Page: Main | 1-6 Light Status Buttons 5-RX Status These buttons coincide with the lights on RX status of the modem. - Page 9 DataStorm D3 User Guide | Standard Functions DataStorm D3 System Status Page Cont. | DataStorm D3 System Status Page: S e n s o r s 1-Dish Elevation 6-Elevation Tilt Displays the actual dish elevation [up/down] The actual tilt of the DataStorm mount up and in degrees.
- Page 10 DataStorm D3 User Guide | Standard Functions DataStorm D3 System Status Page Cont. | DataStorm D3 System Status Page: S a t e l l i t e 1-Target Elevation 4-Sat Elevation Displays the predicted dish elevation in Displays the actual elevation of the Satellite...
-
Page 11: Configuration Page
| Standard Functions DataStorm D3 Configuration Page The DataStorm D3’s configuration page is where changes can be made for finding the satellite, setting up the D3 on a network, and setting other configurations. Below are general explanations of the information displayed on this page. - Page 12 DataStorm D3 User Guide | Standard Functions DataStorm D3 Configuration Pages Cont. | DataStorm D3 Configuration Page: Main 1 | Update Settings To have the D3 accept any changes you must click the ‘Update Settings’ button to store the new configuration.
- Page 13 DataStorm D3 User Guide | Standard Functions DataStorm D3 Configuration Pages Cont. | DataStorm D3 Configuration Page: Main 2 | Update Settings To have the D3 accept any changes you must click the ‘Update Settings’ button to store the new configuration.
- Page 14 DataStorm D3 User Guide | Standard Functions DataStorm D3 Configuration Pages Cont. | DataStorm D3 Configuration Page: Main 2 C o n t . Update Settings To have the D3 accept any changes you must click the ‘Update Settings’ button to store the new configuration.
-
Page 15: User Guide
DataStorm D3 User Guide | Standard Functions DataStorm D3 Configuration Pages Cont. | DataStorm D3 Configuration Page: Main 3 | Update Settings To have the D3 accept any changes you must click the ‘Update Settings’ button to store the new configuration. -
Page 16: About Page
DataStorm D3 User Guide | Standard Functions DataStorm D3 About Page | DataStorm D3 About Page | 1-Version 4-Gateway Displays the current build of D3 software. Displays the IP address of the Modem from the D3’s network configuration. 2-License Displays whether or not the D3 has been 5-ESN registered with MotoSAT. -
Page 17: Advanced Functions
DataStorm D3 User Guide | Advanced Functions DataStorm D3 Manual Motor Controls | DataStorm D3 Manual Motor Controls | 1-Signal Quality Bar 6-Skew Movement Signal quality is attained via the modem. Relates to the left and right motion of the This bar displays quality value. -
Page 18: Calibrations: Tilt
User Guide | Advanced Functions DataStorm D3 Calibrations: Tilt | DataStorm D3 Calibrations: Tilt | THE DISH MUST BE STOWED ONLY USE THIS CALIBRATION IF YOU HAVE A LEGACY STYLE UPPER CONTROL BOARD WHICH IS ATTACHED BETWEEN THE DISH ARMS; THESE HAVE NOT BEEN SHIPPED... -
Page 19: Calibrations: Dish
DataStorm D3 User Guide | Advanced Functions DataStorm D3 Calibrations: Dish | DataStorm D3 Calibrations: Dish | 1-Starting the Dish Calibration 2-Dish Calibration The dish calibration is done to test the The entire dish calibration takes about motor functioning of the dish.