Adjustment Mode Menu - Kenwood TS-2000 Service Manual

All mode multi-band transceiver
Hide thumbs Also See for TS-2000:
Table of Contents

Advertisement

Procedure for writing adjustment firmware (for
both user and adjustment firmware)
1. Remove the lower case and set the slide switch (S1) of
the TX-RX 1 unit (X57-605A) to ON (move the switch to-
ward the front).
2. Connect the RS-232C port of the personal computer with
the COM port of the main unit with a D-SUB (9-pin)
straight cable (female-female).
3. Connect the external power supply (13.8V) to the main
unit and turn the power supply ON. The main unit does
not turn on any indicators, but it is ready to rewrite firm-
ware. Do not operate the power switch on the main unit.
4. Write firmware using writing software. (See the help of
the software for information on how to write it.)
5. After writing the firmware, turn the external power sup-
ply OFF and remove the RS-232C cable.
6. Set the slide switch (S1) of the TX-RX 1 unit (X57-605A)
to OFF (move the switch toward the rear).
7. Turn the external power supply ON.
8. Turn the main unit ON and confirm that the indicator
lights. Then, perform all reset (hold down [A=B] key and
press the [POWER] key) and confirm that the initial state
is displayed.
9. After adjustment, rewrite adjustment software back to
user firmware using the writing software. (See the help
of the software for information on how to write it.)
10. After rewriting user software, check the checksum (hold
down the [N.R.] and [MIC/CAR] keys and press the
[POWER] key. Menu No.125). Then , perform all reset.
Notes :
1. When adjustment software is loaded and the main unit is
turned ON, a beep sounds to indicate the adjustment
mode. This does not indicate a failure.
When any key (except [PF] key) is pressed after a fre-
quency is displayed, the beep stops.
2. Do not return the TS-2000/X that contains adjustment
firmware to the user.
Adjustment mode operation procedure
1. Start the adjustment mode.
Hold down the [N.R.] and [MIC/CAR] keys and press the
[POWER] key. The adjustment mode is set and a menu
number is displayed below the M.CH on the main band
side (left) of the display.
MENU No.
2. Select adjustment mode menu No.
Turn the [MULTI CH] knob to change the menu No.
3. Change adjustment mode setting data.
Setting data can be changed with [+] or [–] key.
4. Write adjustment mode data.
Press [+] or [–] key on the main unit or [UP] or [DOWN]
key on the microphone on menu No. 124.
5. Cancel adjustment mode.
Press the [CLR] key to return to the normal VFO mode.
ADJUSTMENT
Note:
When the power is turned OFF in the middle in the ad-
justment mode, it is canceled.
CN24
Adjustment Mode Menu (Menu No. 00~126)
No.
Adjustment item
00
ALC reference voltage
01
146M BPF center voltage (Main)
02
Variable capacitor voltage
03
Variable capacitor voltage
04
Variable capacitor voltage
05
Variable capacitor voltage
06
435M BPF center voltage (Main)
07
Variable capacitor voltage
08
Variable capacitor voltage
09
Variable capacitor voltage
10
146M BPF center voltage (Sub)
11
Variable capacitor voltage
12
Variable capacitor voltage
13
Variable capacitor voltage
14
Variable capacitor voltage
15
440M BPF center voltage (TX)
16
Variable capacitor voltage
17
Variable capacitor voltage
18
Variable capacitor voltage
19
Variable capacitor voltage (HF TX)
20
10.695M IF filter window
21
455k IF filter window
22
SSB IF gain
23
SSB S1
24
SSB S9
25
SSB S-full scale
26
FM S1
27
FM S-full scale
28
SSB IF gain
29
SSB S1
30
SSB S9
31
SSB S-full scale
32
FM S1
TS-2000/X
S1
OFF
ON
Item
Frequency Mode
14.1M
146M
145.99M
142M
142.00M
144M
144.00M
148M
148.10M
152M
151.90M
440M
440.00M
450M
449.80M
430M
430.00M
420M
420.00M
146M
146.00M
118M
118.00M
132M
132.00M
160M
160.00M
174M
173.90M
435M
435.10M
420M
420.10M
440M
439.99M
450M
449.90M
14M
10.695M
455k
SSB start
SSB S1
SSB S9
SSB S full
FM S1
FM full
SSB start
SSB S1
SSB S9
SSB S full
FM S1
14.1M
USB
USB
USB
USB
USB
USB
USB
USB
USB
USB
FM
FM
FM
FM
FM
USB
USB
USB
USB
14.1M
USB
1.83M
USB
1.83M
USB
14.2M
USB
14.2M
USB
14.2M
USB
14.2M
USB
29.2M
FM
29.2M
FM
50.2M
USB
50.2M
USB
50.2M
USB
50.2M
USB
50.2M
FM
101

Hide quick links:

Advertisement

Table of Contents
loading

This manual is also suitable for:

Ts-2000x

Table of Contents