Subscribe to Our Youtube Channel
Related Manuals for Primus DA11-15
Summary of Contents for Primus DA11-15
- Page 1 DA11-15 OPERATION / MAINTENANCE MANUAL INDUSTRIAL DRYERS PUBLICATION DATE: 10/02 70269601R1...
- Page 3 Installation must conform with local codes or in the absence of local codes with: In the U.S.A., installation must conform to the latest edition of the American National Standard Z223.1/ NFPA 54 “National Fuel Gas Code” and Standard ANSI/NFPA 70 “National Electric Code.” In Canada, installation must comply with Standards CSA-B149.1 or Natural Gas and Propane Code CSA C22.1, latest edition, Canadian Electric Code, Part I.
- Page 4 Notes 70269601...
-
Page 5: Table Of Contents
Table of Introduction..................Model Identification ................Wiring Diagram ..................Contents Serial Plate Location................Safety Information................Important Safety Instructions ............... Operating Instructions ............... 11 Emergency Stop Button on European Models........11 Operating Instructions ................11 Clean Lint Screen/Compartment ............11 Load Laundry..................11 Determine Required Temperature ............ - Page 6 Notes 70269601...
-
Page 7: Introduction
Introduction Model Identification Information in this manual is applicable to these models.† Steam Electric LT025L PT025L PT025S PT025E LT025N PT025N PU025S PU025E 25 Pound (220 Liter) PA025L PU025L PA025N PU025N LT030L PA030N PT030S LU030E LT030N PT030L PU030S PT030E 30 Pound LU030L PT030N PU030E... -
Page 8: Serial Plate Location
Introduction Serial Plate Location When calling or writing for information about your product, be sure to mention model and serial numbers. Model and serial numbers are found on serial plate on rear of machine, and/or inside door hinge. Refer to Figure 1. -
Page 9: Safety Information
Safety Information Precautionary statements (“DANGER,” NOTE: The word “NOTE” is used to communicate “WARNING,” and “CAUTION”), followed by installation, operation, maintenance or servicing specific instructions, are found in this manual and on information that is important but not hazard machine decals. These precautions are intended for the related. -
Page 10: Important Safety Instructions
Safety Information Save These Instructions Important Safety Instructions 14. The interior of the tumbler and the exhaust duct should be cleaned periodically by qualified service personnel. WARNING 15. If not installed, operated and maintained in accordance with the manufacturer’s instructions To reduce the risk of fire, electric shock, or if there is damage to or mishandling of this serious injury or death to persons when... - Page 11 Safety Information 23. Remove laundry immediately after tumbler 29. DO NOT bypass any safety devices. stops. 30. Solvent vapors from dry-cleaning machines 24. Always read and follow manufacturer’s create acids when drawn through the heater of the instructions on packages of laundry and cleaning drying unit.
- Page 12 Notes 70269601...
-
Page 13: Operating Instructions
Operating Instructions WARNING To reduce the risk of fire: • DO NOT DRY articles containing foam rubber or similarly textured rubberlike materials. • DO NOT DRY plastics, anything containing wax or chemicals such as mops and cleaning cloths, or anything dry-cleaned at home with a dry-cleaning solvent. •... -
Page 14: Manual Timer
Operating Instructions COOL HEAT DOWN HIGH PUSH START TMB47N Figure 3 Manual Timer IMPORTANT: If the door is opened during the cycle, the heating system will shut off and the 1. Set the HEAT (Drying) timer for the number of motor will stop. -
Page 15: Electronic Opl Control
Operating Instructions STATUS PROGRAM ON / SELECT HIGH START AUTO TIME DRYING AUTO SPECIAL SPECIAL MEDIUM STOP/RESET COOL DOWN CYCLE TIME AUTO COOL MED LOW TEMP TEMP DOOR OPEN DOWN DISPLAY F/ C SIGNAL CUSTOM MORE LESS SAVE NO HEAT CONDITION CUSTOM PROG... -
Page 16: Electromechanical Coin Control
Operating Instructions SELECT INSERT PUSH TEMPERATURE TEMP COIN START HIGH INSERT QUARTER TURN KNOB PUSH START TMB807N Figure 6 Electromechanical Coin Control IMPORTANT: If the loading door or lint panel door is opened during the cycle, the heating system 1. Set the TEMPERATURE selector at HIGH or will shut off and the motor will stop. -
Page 17: Electronic Coin Control
Operating Instructions SELECT INSERT PUSH TEMP COIN START HIGH START TEMP TEMP TEMP HEAT T361I T361I Figure 7 Electronic Coin Control IMPORTANT: To stop the tumbler at any time during the cycle, OPEN DOOR. To restart the 1. Select HIGH TEMP, MED TEMP, LOW TEMP tumbler, CLOSE door and press START pad. -
Page 18: Netmaster Coin Control
Operating Instructions C851I C851I Figure 8 NetMaster Coin Control IMPORTANT: To stop the tumbler at any time during the cycle, OPEN DOOR. To restart the 1. Select HIGH TEMP, MED TEMP, LOW TEMP tumbler, CLOSE door and press START pad. or NO HEAT by pressing the appropriate temperature pad. -
Page 19: Netmaster Card Control
Operating Instructions C852I C852I Figure 9 NetMaster Card Control IMPORTANT: To stop the tumbler at any time during the cycle, OPEN DOOR. To restart the 1. Select HIGH TEMP, MED TEMP, LOW TEMP tumbler, CLOSE door and press START pad. or NO HEAT by pressing the appropriate temperature pad. -
Page 20: Mdc Coin Control
Operating Instructions SELECT INSERT INSERT PUSH TEMP COINS CARD START DRYING COOL DOWN START DELICATES TMB1964N Figure 10 MDC Coin Control IMPORTANT: To stop the tumbler at any time during the cycle, OPEN DOOR. To restart the 1. Select HIGH TEMP, MED TEMP, LOW TEMP tumbler, CLOSE door and press START pad. -
Page 21: Mdc Card Control
Operating Instructions SELECT PUSH TEMP START DRYING COOL DOWN INSERT CARD HERE START DELICATES TMB1965N Figure 11 MDC Card Control IMPORTANT: To stop the tumbler at any time during the cycle, OPEN DOOR. To restart the 1. Select HIGH TEMP, MED TEMP, LOW TEMP tumbler, CLOSE door and press START pad. - Page 22 Notes 70269601...
-
Page 23: Maintenance
Maintenance WARNING To reduce the risk of electric shock, fire, explosion, serious injury or death: • Disconnect electric power to the tumbler before servicing. • Close gas shut-off valve to gas tumbler before servicing. • Close steam valve to steam tumbler before servicing. •... - Page 24 Maintenance WARNING To reduce the risk of electric shock, fire, explosion, serious injury or death: • Disconnect electric power to the tumbler before servicing. • Close gas shut-off valve to gas tumbler before servicing. • Close steam valve to steam tumbler before servicing. •...
-
Page 25: Monthly
Maintenance WARNING To reduce the risk of electric shock, fire, explosion, serious injury or death: • Disconnect electric power to the tumbler before servicing. • Close gas shut-off valve to gas tumbler before servicing. • Close steam valve to steam tumbler before servicing. •... - Page 26 Maintenance WARNING To reduce the risk of electric shock, fire, explosion, serious injury or death: • Disconnect electric power to the tumbler before servicing. • Close gas shut-off valve to gas tumbler before servicing. • Close steam valve to steam tumbler before servicing. •...
-
Page 27: Before You Call For Service
Before You Call for Service Won’t Won’t Clothes Possible Reason – Corrective Actions Start Heat Not Dry Insert correct coin(s) or valid card if applicable. • Close the loading door tightly. • Close lint panel tightly. • Press the PUSH TO START button. •...
Need help?
Do you have a question about the DA11-15 and is the answer not in the manual?
Questions and answers