Encore 61K650P Operator's Manual

Commercial mowers

Advertisement

61 K6 5 0 P
OPERATORS
MANUAL

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 61K650P and is the answer not in the manual?

Questions and answers

Summary of Contents for Encore 61K650P

  • Page 1 61 K6 5 0 P OPERATORS MANUAL...
  • Page 2: Signal Words

    All Encore dealers are informed of the latest methods to service this equipment and provide prompt and efficient WARNING: service. They carry a full line of Encore service parts. The signal action word “ WARNING” denotes A replacement Operator’s Manual is available...
  • Page 3 ENCORE PROWLER MID CUT Your mower is only as safe as the operator! Operator carelessness or error may result in Drive levers must be in the Neutral position and serious bodily injury. Improper maintenance of the the Blade Clutch must be disengaged before machine may also result in injury.
  • Page 4: Assembly Instructions

    5. Place breather cap on oil tank. Note: The oil tank ASSEMBLY INSTRUCTIONS: is pre-filled from the factory with 20w50 oil and should be visible in the sight glass located on the 1. Remove tractor from the crate. Lay out all the back of the tank.
  • Page 5 Fuel and Oil Recommendations If gasoline is spilled, wipe it up immediately. NOTE: DIESEL UNITS FUEL: Consult Engine Manual for Engine Manufactures Recommendations CAUTION: Operation and Maintenance Information. On Diesel engine model series 432447, 522447 & 582447 - THESE ENGINES ARE CERTIFIED CAUTION: TO OPERATE ON DIESEL FUEL ONLY.
  • Page 6 4. Set Engine Choke Control to for cold starts to NOTE: FULL position. Using multi-grade oils (5w-20, 10w30, and 10w40) will increase oil consumption. Check oils more FOR DIESEL UNITS: WITH THE THROTTLE SET frequently when using them. IN “SLOW “POSITION, TURN THE KEY TO THE “ON”...
  • Page 7: Control Locations

    Let unit run at ½ throttle for 60 seconds, for a cool down period before turning key to OFF position. CONTROLS: GAS UNITS Your Encore Prowler is equipped with a Safety RIGHT LEFT Interlock System that is designed to help prevent FUEL...
  • Page 8 DRIVE ADJUSTMENTS: 4. All neutral creep (rotation) should be adjusted out of the drive. This adjustment is performed If the mower is not tracking straight or if the unit at the adjustable Pump Link on each creeps in the “Neutral Stop” position proceed with corresponding pump.
  • Page 9: Leveling The Deck

    LEVELING THE DECK: 5. Reassemble the spring rod and replace the clevis pin. Now move the deck up and down The deck comes from the manufacturer pre- and recheck the side to side blade leveled. If the deck does not appear to be cutting measurement.
  • Page 10: Mower Blades

    ANTIDOTE: INTERNAL- DRINK LARGE Lug nuts should be checked regularly for QUANTITIES OF WATER OR MILK, FOLLOW tightness. Torque lug nuts to 50ft./lbs. The center WITH MILK OF MAGNESIA, BEATEN EGGS OR hub nut should be torqued to 175-200ft./lbs. VEGETABLE OIL. CALL PHYSICIAN IMMEDIATELY.
  • Page 11: Cutter Deck Gearbox

    ! WARNING ! Do not attempt to straighten a bent blade or weld CHECKING LUBRICANT LEVELS: a broken or cracked blade. Always replace it with a new blade to assure safety. CAUTION The fluid level in the gear box should be checked If a blade cutting edge is dull or nicked, it should after every 100 hours of operation or bi-weekly, be sharpened.
  • Page 12: Drive Shaft

    Maintanence Reference Information LOCATED UNDER THE ENGINE TO THE REAR OF THE MACHINE 72" MID CUT GEAR BOX 52-61" MID CUT GEAR BOX LOCATED TO REAR OF THE DECK Grease Fitting Lubrication List Control Arm Pivots Back Rail 1 Pump / 100 Hours 1 Pump / 40 Hours Caster Support Bearing Drive Shaft...
  • Page 13 Notes:...
  • Page 14 Notes:...
  • Page 15: Encore Warranty

    2 years from the date of purchase against defects in workmanship and materials (90 days for rental use) for any Encore rider that is used for homeowner, commercial or any other income producing purpose. Belts, batteries, and tires are warranted for 90 days against defects in materials and workmanship.
  • Page 16 0802 B ,ENCORE MANUFACTURING CO., INC. 61K650P - OPERATORS MANUAL All rights reserved. Contents subject to change. PROWLER MID-CUT 933095 umber...

Table of Contents