Fujitsu LifeBook T Series User Manual page 100

L i f e B o o k T S e r i e s T a b l e t P C - A p p e n d i x
played. The [Wireless Network Connection Proper-
ties] window will be displayed.
6. Click the [Wireless Networks] tab.
7. Click [Refresh], then choose the correct SSID from
the [Available Networks] window. Click [Config-
ure] and proceed to step 7. If the SSID of your
access point does not appear in the list, click [Add].
The [Wireless Network Properties] window will be
displayed.
8. Select the Association tab if it is not already
selected.
9. Enter the information required for connection to
the wireless LAN.
a. Enter the network name (SSID). (i.e., Enter the
name of the desired network in less than 33
ASCII characters).
For ad hoc connection: Assign the same network
name to all the personal computers to be
connected.
For infrastructure connection: Assign the appro-
priate SSID. The SSID must be identical to the
SSID of the access point. Refer to the access point
manual, or contact your network administrator.
b. For ad hoc connection, check the following field.
For infrastructure connection, clear the check
mark for the following field:
[This is a computer-to-computer (ad hoc) net-
work; wireless access points are not used.]
10. Enter the WEP key for encoding communications
dat
a.
You are strongly recommended to enter
the network key for encoding
communications data. If the network key
is not entered, since the network can be
accessed from all personal computers
containing the wireless LAN function,
there is the danger of your data being
stolen or damaged by other users.
In infrastructure mode, WEP must be
enabled on the access point in order for
WEP to work. The WEP key entered on
the client must be identical to the WEP key
entered in the access point. In ad hoc
mode, the WEP key must be entered
identically on each computer.
a. Check the [Data encryption (WEP enabled)]
check box
94
For ad hoc connection: Clear the check mark
from the [Network Authentication (Shared
mode)] check box.
For infrastructure connection: If the access point
to be accessed has acquired shared-key authenti-
cation, check the [Network Authentication
(Shared mode)] check box.
For open-system authentication, clear the check
mark. For access point setting, refer to the man-
ual of the access point.
b. Clear the check mark from the [The key is
provided for me automatically] check box.
c. Enter data in [Network Key]. Depending on the
number of entered characters or digits, whether
the key is an ASCII character code or a hexadec-
imal code will be identified automatically.
Use five or thirteen characters to enter the key
■
in the ASCII character code format. The char-
acters that can be used as the "network key" are
as follows: 0 - 9, A - Z, _ (underscore), or,
Use 10 or 26 characters to enter the key in the
■
hexadecimal character code format. The char-
acters that can be used as the "network key" in
this case are as follows: 0- 9, A - Z, a - f
For ad hoc connection: Assign the same net-
work key to all the personal computers to be
connected.
For infrastructure connection: Assign the
identical network key that is programmed into
the access point. For this setting, refer to the
access point manual or contact your network
administrator.
d. Confirm the Network key by re-entering the
same data in the [Confirm network key:] field.
e. Make sure that [Key index (advanced)] is set to
"1". (Any value from "1" to "4" can be assigned to
[Key index (advanced)]. "1" is usually assigned,
however).
11. Click the [Authentication] tab and then verify the
settings of [Enable network access control using
IEEE 802.11x].
For internal use at an organization such as a com-
pany, access by wireless LAN clients may be limited
using IEEE 802.11x authentication. Please consult
with your Information Systems department for this
portion of the configuration.
For home use, clear the check mark from [Enable
network access control using IEEE 802.11x].