Table of Contents
Advertisement
Before operation
Enter the standby mode.
The STANDBY indicator lights up.
This means that the amplifier is not disconnected
from the AC mains and a small amount of current is
retained to support the memorized contents and
operation readiness.
To switch the power off, push the POWER switch
again, then the power is cut off and the STANDBY
indicator goes off.
In the standby mode, turn the power on.
1
POWER
POWER
TAPE1/MD
PHONO
PRESET
DISPLAY
Each time the POWER button on the remote control
is pressed, the amplifier is turned on to enter the
operating mode or off to enter the standby mode.
In the standby mode, if the INPUT SELECTOR
button is pressed, the amplifier is turned on
automatically and the desired input is selected.
SYSTEM POWER ON/OFF
If the POWER switch of Sherwood component
connected by the DIGI LINK II or III is kept pushed
and its AC input cord is plugged in the switched AC
outlet, each time the amplifier becomes the standby
or the operating mode, its power is turned off or on.
Under the same conditions, if its AC input cord is not
plugged only in the switched AC outlet, when the
amplifier becomes the standby mode, only its display
is off (meaning that a small amount of current is
retained for operation readiness, etc.)
SPEAKER
P .SCAN
A
B
1
2
3
4
5
6
7
8
9
0
DISC
CD
REPEAT
INTRO
A
B
SCAN
CD
TUNER
DECK SEL.
A
B
TAPE2
MON.
FUNC.
EQ
DECK
USER
FILE
DISPLAY T.MON
SLEEP
MUTE
SYS
VOLUME
REMOTE CONTROL RM-AX-98
1 0
Switch the desired speakers on.
2
Then the corresponding SPEAKER indicator lights up
and the sound can be heard the speakers connected to
"SPEAKER A" or (and) "SPEAKER B" terminals.
When using headphones for private listening, press
both SPEAKER SELECTOR A and B buttons to
switch the speakers off.
Note : For safe amplifier operation, be sure to check
impedance of the speakers connected. (Refer to
"CONNECTING SPEAKERS" on page 6)
Select the desired input source.
3
or
Then the corresponding indicator lights up.
When the TAPE 2 MONITOR button is set to on so that
the TAPE 2 MONITOR indicator lights up, other inputs
can not be heard from the speakers.
To listen to a input source other than TAPE 2 MONITOR,
be sure to set the TAPE 2 MONITOR button to off.
TAPE MONITOR function
You can connect either a tape deck or a graphic equalizer to
the amplifier's TAPE 2 MONITOR jacks.
Only when you listen to the component connected to these
jacks, set the TAPE 2 MONITOR button to on.
If you connect a 3-head tape deck, you can listen to the
sound being recorded during recording, not the source
sound.
For further details, refer to the operating instructions of the
component connected.
SPEAKER
POWER
SPEAKER
P .SCAN
A
B
A
B
1
2
3
4
5
6
7
8
9
0
DISC
CD
REPEAT
INTRO
A
B
SCAN
CD
TUNER
DECK SEL.
A
B
TAPE1/MD
TAPE2
MON.
PHONO
FUNC.
or
EQ
DECK
PRESET
USER
FILE
DISPLAY T.MON
DISPLAY
SLEEP
MUTE
SYS
VOLUME
REMOTE CONTROL RM-AX-98
POWER
SPEAKER
P .SCAN
A
B
CD
TUNER
1
2
3
4
5
6
7
8
9
0
DISC
CD
REPEAT
INTRO
A
B
SCAN
TAPE1/MD
TAPE2
CD
TUNER
DECK SEL.
A
B
TAPE1/MD
TAPE2
MON.
MON.
PHONO
FUNC.
PHONO
EQ
DECK
PRESET
USER
FILE
DISPLAY T.MON
DISPLAY
SLEEP
MUTE
SYS
VOLUME
REMOTE CONTROL RM-AX-98
Advertisement
Table of Contents
