Table of Contents
Advertisement
Quick Links
OPERATING INSTRUCTIONS
BEDIENUNGSANLEITUNG
MANUAL DE INSTRUCCIONES
STEREO INTEGRATED AMPLIFIER AX-5103
POWER
ON/OFF
CD
TUNER
TAPE 1/MD
PHONO
STANDBY
REMOTE SENSOR
STANDBY
SPEAKER
A
BASS
TREBLE
B
PHONES
-10
10+
-10
10+
AX-5103
Stereo Integrated Amplifier
Stereo-Vollverstärker
Amplificatore lntegrato Stereo
Amplificador Integrado Estéreo
ISTRUZIONI PER L'USO
TAPE 2 MONITOR
VOLUME
BALANCE
DIRECT
LOUDNESS
LEFT
RIGHT
MIN
MAX
Advertisement
Table of Contents
Related Manuals for Sherwood AX-5103
Summary of Contents for Sherwood AX-5103
- Page 1 OPERATING INSTRUCTIONS BEDIENUNGSANLEITUNG ISTRUZIONI PER L’USO MANUAL DE INSTRUCCIONES STEREO INTEGRATED AMPLIFIER AX-5103 POWER ON/OFF TUNER TAPE 1/MD PHONO TAPE 2 MONITOR STANDBY REMOTE SENSOR STANDBY VOLUME SPEAKER BASS TREBLE BALANCE DIRECT LOUDNESS PHONES LEFT RIGHT AX-5103 Stereo Integrated Amplifier Stereo-Vollverstärker...
-
Page 2: Fcc Information
Congratulations on Your Purchase! FOR U.S.A. Your new high fidelity Amplifier is designed to deliver FCC INFORMATION maximum enjoyment and years of trouble free service. This equipment has been tested and found to comply Please take a few moments to read this manual thoroughly. with the limits for a Class B digital device, pursuant to It will explain the features and operation of your unit and Part 15 of the FCC Rules. -
Page 3: Ac Voltage Selection
FOR U.S.A AND CANADA ......120 V FOR OTHER COUNTRIES ....115 V/ 230 V FOR YOUR SAFETY FOR YOUR SAFETY Units shipped to the U.S.A and Canada are designed Units shipped to countries other than the above for operation on 120 Volts AC only. countries are equipped with an AC voltage selector switch on the rear panel. - Page 4 Introduction UNPACKING AND INSTALLATION ......................2 READ THIS BEFORE OPERATING YOUR UNIT ..................3 System Connections ............................5 Front Panel Controls ............................7 DIGI LINK III System Remote Controls ....................8 REMOTE CONTROL OPERATION RANGE ....................9 LOADING BATTERIES ..........................9 Operations LISTENING TO A PROGRAM SOURCE ....................
-
Page 5: Connecting Audio Components
Graphic equalizer PHONO TUNER MONITOR Connect this jack to the DIGI LINK jack of the external Sherwood component that uses the DIGI LINK II or III remote control system. REC (LINE IN) PLAY (LINE OUT) Tape deck 1 or MD recoder... -
Page 6: Connecting Speakers
AC INPUT CORD Plug this cord into a wall AC outlet SER. NO AC INPUT 230V~50Hz 190W MODEL NO. AX-5103 INTEGRATED AMPLIFIER DESIGNED IN USA SPEAKER A ASSEMBLED IN KOREA CAUTION TAPE 1 TAPE 2 PHONO TUNER DIGI LINK SPEAKER IMPEDANCE... - Page 7 STEREO INTEGRATED AMPLIFIER AX-5103 POWER ON/OFF TUNER TAPE 1/MD PHONO TAPE 2 MONITOR REMOTE SENSOR STANDBY VOLUME SPEAKER BASS TREBLE BALANCE DIRECT LOUDNESS PHONES LEFT RIGHT POWER SWITCH BALANCE CONTROL KNOB Press this switch to enter the power off or the standby Adjust the stereo balance between left and right mode.
- Page 8 You can remotely control not only this amplifier but also Sherwood compatible components bearing the DIGI LINK II or III logo. For system remote control operation, first make the DIGI LINK connections. PRESET SCAN BUTTON For scanning preset stations in sequence in tuner mode.
- Page 9 STEREO INTEGRATED AMPLIFIER AX-5103 POWER ON/OFF TUNER TAPE 1/MD PHONO TAPE 2 MONITOR REMOTE SENSOR STANDBY VOLUME SPEAKER BASS TREBLE BALANCE DIRECT LOUDNESS PHONES LEFT RIGHT Use the remote control unit within a range of about 7 meters (23 feet) and angles of up to 30 degrees...
-
Page 10: System Power On/Off
To listen to a input source other than TAPE 2 MONITOR, be sure to set the TAPE 2 MONITOR button to off. SYSTEM POWER ON/OFF If the POWER switch of Sherwood component TAPE MONITOR function connected by the DIGI LINK II or III is kept pushed... - Page 11 To emphasize the sound of frequencies Operate the selected component for that are difficult to hear at low volume playback. levels. Adjust the volume to a comfortable listening level. To cancel the loudness effect, press this switch again. POWER SPEAKER P .SCAN To listen to a program source without DISC...
- Page 12 The volume and tone (bass, treble) settings, etc. have no effect on the recording signals. Recording with TAPE 1/MD Recording with TAPE 2 MONITOR Select the desired input as recording Select the desired input as recording source except for TAPE 1/MD and TAPE source except for TAPE 2 MONITOR.
- Page 13 If your unit should not perform as expected, consult the table below to see if the problem can be corrected before seeking help from your dealer or our service organization. PROBLEM POSSIBLE CAUSE REMEDY No power The AC input cord is disconnected Connect the cord securely.
- Page 14 Power output, 8 Ω, THD 0.3 %, 40 Hz 20 kHz ....................2 100 W Total harmonic distortion, 8 Ω, 100 W, 1 kHz ......................0.03 % Intermodulation distortion 60 Hz : 7 kHz = 4 : 1 SMPTE, 8 Ω, 100 W ......................0.05 % Input sensitivity, 47 kΩ...