You can find the rating plate on the back of the dryer.
Drum interior light (depending on model) (bulb E14, 25 W)
The drum lights up after the door is opened or closed, and after the programme starts,
and switches off automatically. Changing the bulb
Residual moisture in the
fabrics after spinning
Cotton 7 kg
Easy-Care 3.5 kg
* Programme setting for testing in accordance with applicable standard EN61121.
** The values may differ from those specified, depending on the type of fabric, composition of
laundry to be dried, residual moisture in the fabric and the amount of laundry being loaded.
Cotton 7 kg / 3.5 kg*
97 min / per cycle
***Programme setting for testing and energy labelling in accordance with Directive 2010/30/EU.
For easier loading and unloading. The basket contained in the drawer can be used to carry
Washer-dryer stack connection set
The dryer can be placed on top of a suitable washing machine with the same width and depth
to save space. The dryer must be fastened to the washing machine using this connection set.
With pull-out worktop: WZ 20300
Connection fittings for condensation outlet
The condensation is conveyed directly via a hose.
Installation underneath the worktop
Instead of the appliance covering plate, you must have a metal cover fitted by
60 x 60 x 85 cm (height adjustable)
approximately 45 kg
see appliance rating plate
(The value on the label is achieved at the maximum heat setting.)
Annual energy consumption
504 kWh / per year
(from after-sales service using order number)
What to do if ...
If you cannot rectify a fault yourself (e.g. switching off/on), please contact our after-sales
service. We will always find an appropriate solution and will avoid unnecessary visits by
engineers. Trust the expertise of the manufacturer and rest assured that the repair will be
carried out by trained service technicians using original spare parts. The contact details of your
local after-sales service can be found in the enclosed after-sales service directory, or by
calling one of these numbers:
– GB 0844 8928999 ( Calls from a BT landline will be charged at up to 3 pence per minute.
A call set-up fee of up to 6 pence may apply.)
– IE 01450 2655 (0.03 € per minute at peak. Off peak 0.0088 € per minute.)
When contacting the after-sales service, please quote the appliance's product number (E no.)
and production number (FD) (see the inside of the door).
Set the programme selector to Off and remove the appliance plug from the socket.
The Start/Stop indicator lamp
does not light up.
The display panel light and
indicator lights (depending on
model) go out and the Start/Stop
indicator light flashes.
The Empty water and
Start/Stop indicator lamp flash.
The Clean filter and Start/Stop
indicator lamp flash.
Dryer does not start.
Water is running out.
The door opens by itself.
Drying result is not satisfactory
(laundry feels too damp).
Drying time too long.
The humidity in the room
One or more indicator lights for
programme status are flashing.
The interior light is not working
(depending on model).
Mains plug plugged in?
Check the socket fuse.
Energy-saving mode is activated
see the separate Energy-saving mode instructions.
Empty the condensation container.
If featured, check hose for condensation outlet.
Clean the fluff filter and/or air cooler under running water
Start/Stop button selected?
Ambient temperature greater than 5 °C?
Align dryer horizontally.
Clean air cooler seal.
Push the door closed until you hear it engage.
Laundry load exceeded?
Remove articles of clothing immediately after the end of the
programme, hang up and pull into shape.
Unsuitable programme selected
Warm laundry feels damper than it actually is.
The selected programme does not suit the load. Use another
drying programme or, in addition, select the time programme
Use fine adjustment for the drying result
Fine layer of limescale on the humidity sensors
Clean the humidity sensors
Programme termination, e.g. tank full, mains power supply failure,
door open or maximum drying time reached.
Rinse the fluff filters under running water
Insufficient supply of air
ensure that air can circulate.
Air inlet possibly blocked
Ambient temperature higher than 35 °C
Make sure the room is sufficiently ventilated.
Remove laundry from the dryer immediately and spread out.
This allows the heat to dissipate.
Clean filter and air cooler
Check installation conditions
Switch off, leave to cool down, switch on again, restart
Pull out the appliance plug, remove the cover cap in the interior
above the door (use Torx 20 screw driver) and replace the bulb.
Close the cover cap.
Never operate the dryer without a cover cap.
Page 1/2 and 5/6.
ventilate the room.