PetNovations CatGenie Operation page 15

2F
3A
3D
www.catGenie.com
STEP 2. WASHING CATGENIE
D. Unsnap the 3 Clips that run diagonally on the outside
of the Hopper opposite the hinged side. Open the Hopper
like a book and keep two pieces together.
E. When open, pay special attention to the Impeller.
Impeller is the black fan-like part attached to the bottom
of the metal shaft. Remove any cat hair, Granules, or
2D
other foreign matter from the Impeller blades, the metal
shaft, and the area that encloses the Impeller.
Wash the Hopper, Impeller, and Water Sensor with a
mild liquid soap and water. Use a sponge or soft cloth.
Rinse thoroughly. Snap Hopper closed. It's closed when
snaps click and both sides stay together with no gaps.
F. PUT THE RED WASHER BACK ON THE HOPPER
and lubricate ONLY the outside of the Washer with
2E
any food oil (i.e. olive, corn, etc.) or baby oil.
G. Wash the Base and Brim with a mild liquid soap
and water. Rinse thoroughly. Lift up the Base enough to
2F
allow water to run out of the Genie DrainHose. Dump
any remaining water from the Base.
Check that all parts are clean and no soap, cat hair, or granules remain.
Dry the Base and Brim with a lint-free cloth or paper towels.
H. Wash, rinse and dry the Hopper Cover. Pay particular attention to the
inside back of the Cover for any remaining dirt.
STEP 3. REASSEMBLING CATGENIE.
IMPORTANT: THE RED DRAIN WASHER must be in place on the Hopper.
A. Put the Hopper back in its place in the Base.
B. Coil the Genie DrainHose inside the Base. Take Base, Brim, and Hopper
Cover back to the CatGenie site. Make sure the Genie DrainHose is in the
groove in the back of the Base. Place the Base back by the Processing Unit.
C. The Bowl has a recess in the bottom that must fit over the nipple in the
3B
center of the Base. Carefully put the Bowl back in the Base. Check to be sure
that the Bowl spins easily in the Base.
D. Hold the back of the Brim up over the back of the Base. Push the Black Clip
on the end of the metal Arm up through the slot. Lower the Brim onto the Base
and, working from back to front, press the Brim onto the Base. You will hear a
snap when both parts lock together. Attach the GenieHand to the Arm and push
3C
the GenieHand back into the upright position.
E. NEVER WASH THE PROCESSING UNIT. Gently wipe it off with a soft damp
3E
cloth. If the Orange Niplet on the bottom of the Unit has built-up SaniSolution
residue, carefully pull it off, rinse it and put it back. Make sure it is secure.
Put the Processing Unit back on the Brim taking care to align it correctly and
seat it securely in its slot. Replace the Hopper Cover. Push the water supply line
and power cord back into their respective grooves.
Move the CatGenie back in place and plug it into the electric outlet. The
CatGenie will do a sequence of self-checks indicated by Beeping sounds and
LEDs Lights. IF IT DOES NOT, unplug it. Then lift the Processing Unit out and
carefully realign it and reseat it in its place in the Brim.
15
™ (continued)
CLEANING OUT A
CLOG (continued)
Follow directions for
cleaning and re-
assemble on site.
BUT do not attach
the GenieHand
Run a wash cycle.
Because Granules
are wet, connect
the GenieHand
after Scoop Cycle.
Press Start/Pause
Button and replace
GenieHand only
for wash and dry
cycles. Press to
take off Pause and
restart cleaning.
1-888-735-3927