Table of Contents
Advertisement
Quick Links
Download this manual
See also:
User Manual
AV Connectivity, Distribution And Beyond...
Before connecting, operating or adjusting this product, please read this instruction booklet carefully and completely.
© 2013 Avenview Inc. All rights reserved.
The contents of this document are provided in connection with Avenview Inc. ("Avenview") products. Avenview makes no representations or
warranties with respect to the accuracy or completeness of the contents of this publication and reserves the right to make changes to specifications
and product descriptions at any time without notice. No license, whether express, implied, or otherwise, to any intellectual property rights is granted
by this publication. Except as set forth in Avenview Standard Terms and Conditions of Sale, Avenview assumes no liability whatsoever, and disclaims
any express or implied warranty, relating to its products of Avenview Inc. is strictly prohibited.
VIDEO WALLS
VIDEO MATRIX SWITCHES
EXTENDERS
CABLES & ACCESSORIES
Setup Guide
VIDEO PROCESSORS
SPLITTERS
Model #: W-HDM3D-100-SET
WIRELESS
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Avenview W-HDM3D-100-SET
Summary of Contents for Avenview W-HDM3D-100-SET
-
Page 1: Setup Guide
No license, whether express, implied, or otherwise, to any intellectual property rights is granted by this publication. Except as set forth in Avenview Standard Terms and Conditions of Sale, Avenview assumes no liability whatsoever, and disclaims... -
Page 2: Table Of Contents
Step 3: Connect the Receiver unit (Rx) to a Destination ..............5 Step 4: Powering the Transmitter and Receiver units ................6 optional Accessory: CW-hDMDVI-100 DC Splitter ................6 An alternate power method for wireless RX or Tx units ..............6 Step 5: Sync and Begin Wireless Transmission ..................6 TRouBlEShooTING ........................7 www.avenview.com Page 2... -
Page 3: Getting Started
INTRoDuCTIoN Avenview W-hDM3D-100 transmitter and receiver system sends a wireless high quality audio and video signal (up to 1080p/60hz) anywhere within a typical medical operating room. The transmitter is designed to be connected to a video source, such as an endoscopic camera, and the receiver is designed to be connected to a video display monitor. -
Page 4: Package Contents
12. Cable guides and extra screws 13. Power cable for CW-PS-hDMSP-100 Verify that you received all components of your respective package. Inspect each component and verify that none of the components have been tampered with in any way. www.avenview.com Page 2... -
Page 5: Plan The Installation
• The Tx and Rx should be no more than 10 meters (33 ft.) apart. • The Tx and Rx should be between 1.8-3 meters (6-10 ft.) above the floor. • The Tx and Rx should not be in a confined location. www.avenview.com Page 3... -
Page 6: Step 1: Connect The Source To The Transmitter Unit (Tx)
W-hDM3D-S-100 system will be unable to successfully transmit a video signal. In this situation, the CW-hDMDVI-100 scaler/converter can be used to regulate the signal from the source into a standardized video signal that the W-hDM3D-S-100 system can understand. Incoming Proprietary Signal Timing Standard www.avenview.com Page 4... -
Page 7: Cw-Hdmdvi-100 Scaler/Converter (Continued)
Converted output signal type. Pressing the mode button again will move to the next output type, and loop through all modes. Step 3: Connect the Receiver Unit (Rx) to a Destination Connect the W-hDM3D-S-100 Rx (receiver) to a destination using an hDMI to DVI cable. www.avenview.com Page 5... -
Page 8: Step 4: Powering The Transmitter And Receiver Units
To re-sync a connection between Tx and Rx, push and holding down the “Pinhole Switch” button for 4-5 seconds or until the lED flashes.Be sure to select the appropriate DVI input mode on the destination display monitor. www.avenview.com Page 6... -
Page 9: Troubleshooting
If all connections are in place and still the system is not syncing, turn the Tx and Rx power off, wait 15 seconds, then turn both units on again. Also, refer to Step 2 and double check if the W-hDM3D-S-100 Scaler/Converter is outputting a mode that is compatible with your display monitor by pressing the mode button. www.avenview.com Page 7... -
Page 10: Technical Support
Disclaimer While every precaution has been taken in the preparation of this document, Avenview Inc. assumes no liability with respect to the operation or use of Avenview hardware, software or other products and documentation described herein, for any act or omission of Avenview concerning such products or this documentation, for any interruption of service, loss or interruption of business, loss of anticipatory profits, or for punitive, incidental or consequential damages in connection with the furnishing, performance, or use of the Avenview hardware, software, or other products and documentation provided herein.
Need help?
Do you have a question about the W-HDM3D-100-SET and is the answer not in the manual?
Questions and answers