Alexor PC9155-433/868 Installation Manual page 22

PC9155 Wireless Alarm System
Step
Once in the programming section, the 4-digit number "0111" is displayed. Enter
2
See the tables below for details of Digit 1, 2, 3 and 4.
Step
After entering '0001', the first telephone entry is displayed. Enter the monitoring station
3
telephone number after the "D". Do NOT delete any of the remaining "Fs"
E.g., To enter 02-1234-5678:
Press
to complete the entry. See section [301] for additional details.
Step
After programming the first telephone number, the system account code is displayed.
4
The system account code can be any 6-digit combination of numbers (0-9) and letters (A-
F). If the system account code is 4-digits, the last two digits must be 'FF'.
To enter the letters A through F, press
through F respectively. Press
E.g.,: To enter "1234FF" Press
See section [310] for additional details.
Step
After programming the system account code, the downloading access code is displayed.
5
Enter the new downloading access code or press
section [403] for additional details.
Step
The entry delay is the amount of time given to disarm the alarm system, after entering the
6
premises through a delay type zone, before an alarm is sounded.
• Press
delay between 001 and 255.
E.g., Press 020 for a delay of 20 seconds. See section [005] for additional details.
Step
The exit delay is the amount of time given to exit the premises after pressing the Arm key
7
before the alarm system is armed.
• Press
delay between 001 and 255.
E.g., Press 030 for a delay of 30 seconds. See section [005] for additional details.
Step
After programming the exit delay, the installer code is displayed. Enter a 4 or 6-digit code
8
depending on the value in section [701] option 5.
Press to exit Template Programming. See section [006] for installer code details.
• Digit 1 selects one of the following zone definition options for the first 8 zones. A '0' in the digit 1 location
indicates that the default settings for the first 8 zones are in place unless overridden during enrollment. See section [001] for defaults.
Option Zn1
0 This entry will not change the currently programmed zone definitions.
1 01
2 01
3 01
4 01
5 01
6 01
7 01
Refer to Chapter 5 for zone definition details
to accept the existing default programming.
,
then the numbers 1 through 6 for the letter A
,
again to revert back to decimal entry.
to accept the default time of 30 seconds (030) or enter an entry
to accept the default time of 120 seconds (120) or enter an entry
Zn2 Zn3 Zn4 Zn5
03 03 03 04
03 03 05 05
03 03 05 05
01 03 03 03
03 03 06 05
03 03 06 05
01 06 06 06
followed by
.
,
to proceed to the next step. See
Zn6 Zn7 Zn8
04 04 04
05 05 88
05 05 87
03 03 03
05 05 05
05 05 88
01 01 01
4-2
Enter Data
0 111
D FFFFFFFFFFFFFF F
FFFFFFFFFFFFFFFF
D0212345678 FFFF
FFFFFFFFFFFFFFFF
Enter Hex Data
F FFFFF
Enter Hex Data
1234FF
Enter Hex Data
9 15500
Enter Data
0 30
Enter Data
1 20
Enter Data
5 555
Zone Definitions (Options 1- 7)
01 Delay 1
02 Delay 2
03 Instant
04 Interior
05 Interior Stay/Away
06 Delayed Stay/Away
87 Delayed 24 Hr.
88 Standard 24 Hr. Fire
F