INSTALLATION 1. GOOD AIR CIRCULATION - Avoid any partitions or objects which may restrict air flow. - Be sure there is sufficient air space to allow air flow at the rear of the unit. 2. DO NOT PLACE NEAR HEAT - High ambient temperature will adversly affect cooling efficiency.
CLEANING 1. CLEANING THE INTERIOR AND EXTERIOR - The interior and exterior of the unit can be cleaned using warm water with soap. - Do not use an abrasive cleaner because it will scratch the stainless steel surface. 2. CLEANING THE CONDENSER FINS - To maintain proper refrigeration performance, the Condensing coil must be free of dust, dirt and grease.
BASIC OPERATION WCC-23SR REFRIGERATOR WCR-23SR 1. The controller(thermostat) is located at the top inside of the unit. 2. The factory setting for the control is ‘Normal’, and maintains about 38˚F (3˚C) inside. 3. Set toward “Cool” for higher temperature and “Cold” for lower temperature. NORMAL COLD Temperature Controller...
Page 7
BASIC OPERATION CCR-23SR REFRIGERATORS CCR-49DR CCR-72TR 1. Plug in and turn on the power switch located on the bottom of the top grille right side. The Display panel will be lighted and make a beep sound. The compressor will begin to run.
Page 8
DISPLAY PANEL OF REFRIGERATOR TEMP. SETTING TEMP. CONTROL BUTTON (SEE TO PAGE 8) INNER TEMP. (SEE TO PAGE 9) ˚F TEMPERATURE TEMPERATURE Q.C. DOOR QUICK COOLING QUICK COOLING QUICK COOLING INDICATOR BUTTON (SEE TO PAGE 8) FAN RUNNING INDICATOR DOOR OPENING INDICATOR...
Page 9
QUICK COOLING 1. If you push the Q.C. (Quick Cooling) button, the compressor will run continuously until D-Senser detect 14˚F (-10˚C) to bring down the temperature more quickly. (max.comp.run time = 120 min.) 2. If you push the Q.C. button again during Quick Cooling mode, the compressor will return to the normal operation.
Page 10
INNER TEMPERATURE DISPLAY 1. It displays inside temperature. 2. Display range is 14˚F to 69˚F (-10˚C ~ +20˚C). 3. When inside temperature is lower than 14˚F, the panel will display ‘ ’. and, higher than 69˚F, the panel will display ‘ ’.
BASIC OPERATION CCR-23SF CCR-49DF FREEZERS CCR-72TF WCR-23SF 1. Plug in and turn on the power switch located on the bottom of the top grille right side. The Display panel will be lighted and make a beeping sound. The compressor will begin to run.
Page 12
DISPLAY PANEL OF FREEZER TEMP. SETTING TEMP. CONTROL BUTTON (SEE TO PAGE 12~13) INNER TEMP. (SEE TO PAGE 14) ˚F TEMPERATURE TEMPERATURE D.F. DOOR MANUAL DEFROST MANUAL DEFROST MANUAL DEFROST INDICATOR BUTTON (SEE TO PAGE 12~13) FAN RUNNING INDICATOR DOOR OPENING INDICATOR...
Page 13
FOR CCR-23SF, CCR-49DF, CCR-72TF MANUAL DEFROST 1. If you push MANUAL DEFROST button for 5 seconds, the Defrost will start. 2. During the Manual Defrost mode, the Up/Down button for the temp. control can not make the compressor cycle ON or OFF. 3.
Page 14
FOR WCR-23SF MANUAL DEFROST 1. If you push MANUAL DEFROST button for 5 seconds, the Defrost will start. 2. During the Manual Defrost mode, the Up/Down button for the temp. control can not make the compressor cycle ON or OFF. 3.
Page 15
INNER TEMPERATURE DISPLAY 1. The Refrigerator/Freezer displays the inside temperature. 2. Display range is -50˚F to 50˚F (-45˚C ~ +10˚C). 3. When inside temperature is lower than -50˚F, the panel will display ‘ ’. and, higher than +50˚F, the panel will show ‘ ’.
INSTALLATION METHOD OF REVERSE DOOR 1. REMOVE THE BOTTOM GRILL GRILL * T ** THE BOTTOM GRILL IS FIXED BY LATCH, SO YOU CAN REMOVED IT BY HANDS. TOP HINGE 2. REMOVE THE TOP GRILL ** THE TOP GRILL IS FIXED BY SCREWS, SO YOU NEED SCREW DRIVER.
BEFORE REQUESTING SERVICE SYMPTOMS CAUSES SOLUTIONS Freezer is melting • The setting temperature is too • Push the temperature down food. high to contain food fresh. button for lower temperature. The unit does not • There is a power connection •...
WARRANTY LIMITED ONE YEAR PARTS & LABOR WARRANTY Master-Bilt Products (the "Company") warrants to the original purchaser-user that its refrigeration equipment, at the time of delivery, will be free from defects in material and workmanship. Master-Bilt will bear the reasonable and customary labor expense to repair or replace any component part (including said part) found to be defective under the terms and conditions as outlined under Master-Bilt’s standard one (1) year parts warranty.
TERMS OF SALE 1. PRICES. Master-Bilt reserves the right to change the price of the equipment without notice. All quotations for equipment shall be void if not accepted within 30 days. 2. DELIVERY. Shipping or delivery date is approximate. Seller will not be liable for failure to deliver due to strikes, supplier’s delays, changes requested by buyer or any causes beyond Master-Bilt’s control.