Daikin R410A Split Series Installation Manual
R410a split series room air conditioner
Hide thumbs
Also See for R410A Split Series:
- Service manual (381 pages) ,
- Installation manual (177 pages) ,
- Technical manual (44 pages)
Table of Contents
Advertisement
Quick Links
MODELS
FTXS20J2V1B
FTXS25J2V1B
FTXS35J2V1B
FTXS42J2V1B
FTXS50J2V1B
DAIKIN ROOM AIR CONDITIONER
INSTALLATION MANUAL
R410A Split Series
Installation manual
Installationsanleitung
Manuel d'installation
Montagehandleiding
Manual de instalación
Manuale d'installazione
ã÷åéñßäéï åãêáôÜóôáóçò
Manual de Instalação
óêîâîäñòâî ïî ìîíòàæó
ontaj kýlavuzlarý
Advertisement
Table of Contents
Related Manuals for Daikin R410A Split Series
Summary of Contents for Daikin R410A Split Series
-
Page 1: Installation Manual
DAIKIN ROOM AIR CONDITIONER INSTALLATION MANUAL R410A Split Series Installation manual Installationsanleitung Manuel d’installation Montagehandleiding Manual de instalación Manuale d’installazione ã÷åéñßäéï åãêáôÜóôáóçò Manual de Instalação óêîâîäñòâî ïî ìîíòàæó ontaj kýlavuzlarý MODELS FTXS20J2V1B FTXS25J2V1B FTXS35J2V1B FTXS42J2V1B FTXS50J2V1B... - Page 2 3SB64417-11G...
-
Page 3: Safety Precautions
Safety Precautions • The precautions described herein are classified as WARNING and CAUTION. They both contain important information regarding safety. Be sure to observe all precautions without fail. • Meaning of WARNING and CAUTION notices WARNING ..Failure to follow these instructions properly may result in personal injury or loss of life. CAUTION .. -
Page 4: Choosing An Installation Site
Accessories – Indoor unit Mounting plate Remote controller holder Operation manual Titanium apatite photocatalytic Dry battery AAA. LR03 Installation manual air-purifying filter (alkaline) Indoor unit fixing screw Wireless remote controller (M4 × 12L) Choosing an Installation Site • Before choosing the installation site, obtain user approval. Indoor unit •... -
Page 5: Indoor Unit Installation Drawings
Indoor Unit Installation Drawings How to attach the indoor unit Mounting Hook the claws of the bottom frame plate to the mounting plate. If the claws are difficult to hook, A Mounting plate remove the front grille. Clip How to remove the indoor unit Push up the marked area (at the lower part of the front grille) to Bottom frame... -
Page 6: Removing And Installing Front Panel
Preparation before Installation Removing and installing front panel • Removal method Hook fingers on the tabs on the left and right of the main body, and open until the panel stops. Slide the front panel sideways to disengage the rotating shaft. Then pull the front panel toward you to remove it. •... -
Page 7: How To Set The Different Addresses
Preparation before Installation How to set the different addresses When two indoor units are installed in one room, the two wireless remote controllers can be set for different addresses. 1) Remove the metal plate electrical wiring cover. (Refer to the Removal/attachment methods of metal plate electrical wiring covers.) 2) Cut the address jumper (JA) on the printed circuit board. -
Page 8: Flaring The Pipe End
• Attachment methods of metal plate electrical wiring cover Attach the metal plate electrical wiring cover as shown below. 1) Lean the metal plate electrical wiring cover as shown in the figure and attach tab (1) on the lower side to the electrical wiring box. -
Page 9: Caution On Piping Handling
Refrigerant Piping Work Refrigerant piping CAUTION • Use the flare nut fixed to the main unit. (To prevent cracking of the flare nut by aged deterioration.) • To prevent gas leakage, apply refrigeration oil only to the inner surface of the flare. (Use refrigeration oil for R410A.) •... -
Page 10: Installing The Mounting Plate
Indoor Unit Installation Installing the mounting plate • The mounting plate should be installed on a wall which can support the weight of the indoor unit. 1) Temporarily secure the mounting plate to the wall, make sure that the panel is completely level, and mark the boring points on the wall. - Page 11 Indoor Unit Installation Laying piping, hoses, and wiring 4-1. Right-side, right-back, or right-bottom Remove pipe port cover piping here for right-side piping 1) Attach the drain hose to the underside of the refrigerant pipes with adhesive vinyl tape. Right-back piping Remove pipe port cover 2) Wrap the refrigerant pipes and drain hose together here for right-bottom piping...
-
Page 12: Drain Piping
Wiring , install as described in the installation manual supplied with the multi outdoor With a multi indoor unit unit. 1) Strip wire ends (15mm). 2) Match wire colours with terminal numbers on indoor and outdoor unit’s terminal blocks and firmly screw wires to the corresponding terminals. -
Page 13: Trial Operation And Testing
Trial Operation and Testing Trial operation and testing 1-1 Measure the supply voltage and make sure that it falls in the specified range. 1-2 Trial operation should be carried out in either cooling or heating mode. ■ For Heat pump •... - Page 14 Two-dimensional bar code is a code for manufacturing. 3P266962-2A M10B169 (1101) HT...