Page 1 www.carburetor-manual.com Would you like some Free Manuals? http://carburetor-manual.com/free-shop-manual-club-t-13.html Also visit http://freeshopmanual.com for more Free Manuals Also Visit my website for 7 FREE Download Manuals starting with this one. "The ABC's of Carburetion" Click Here Now file:///C|/Documents%20and%20Settings/Tim/Desktop/carburetor-manual-welcome/index.htm[4/25/2009 11:42:20 AM]...
Page 2 Contents Before driving Introduction Instrumentation Controls and features Seating and safety restraints Starting and driving Starting Driving Roadside emergencies Servicing Maintenance and care Capacities and specifications Customer assistance Reporting safety defects Index All rights reserved. Reproduction by any means, electronic or mechanical including photocopying, recording or by any information storage and retrieval system or translation in whole or part is not permitted without written authorization from Ford Motor Company.
Page 3 Introduction The following warning may be required by California law: CALIFORNIA Proposition 65 Warning WARNING: Engine exhaust, some of its constituents, and certain vehicle components contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.
Page 4: Introduction
Introduction BREAKING-IN YOUR VEHICLE There are no particular guidelines for breaking-in your vehicle. During the first 1,600 km (1,000 miles) of driving, vary speeds frequently. This is recommended to give the moving parts a chance to break in. INFORMATION ABOUT THIS GUIDE The information found in this guide was in effect at the time of printing.
Page 5 Introduction These are some of the symbols you may see on your vehicle. Vehicle Symbol Glossary Safety Alert See Owner’s Guide Fasten Safety Belt Air Bag-Front Air Bag-Side Child Seat Child Seat Installation Child Seat Tether Warning Anchorage Brake System Anti-Lock Brake System Brake Fluid - Traction Control...
Page 6 Introduction Vehicle Symbol Glossary Child Safety Door Power Window Lockout Lock/Unlock Interior Luggage Compartment Release Panic Alarm Symbol Engine Oil Engine Coolant Engine Coolant Do Not Open When Hot Temperature Avoid Smoking, Flames, Battery or Sparks Battery Acid Explosive Gas Fan Warning Power Steering Fluid Maintain Correct Fluid...
Page 7 Instrumentation Windshield wiper/washer Instrument cluster control (pg. 8) (pg. 83) Turn signal lever (pg. 77) Headlamp control (pg. 31) Instrument panel dimmer control (pg. 32) Driver air bag Reverse sensing system* (pg. 149) (pg. 33) Steering wheel controls* Speed control (pg.
Page 8: Instrumentation
Instrumentation Gearshift (includes Audio system overdrive button) (pg. 54) (pg. 183) Message center* (pg. 19) TRIP DUAL AUTO Climate control system (pg. 36) Power adjustable foot pedals (pg. 33)
Page 9 Instrumentation WARNING LIGHTS AND CHIMES Standard instrument cluster CHECK GAGE SERVICE ENGINE SOON DOOR BRAKE AJAR TRIP CHECK FUEL WASH Optional instrument cluster HI TEMP LOW OIL SERVICE ENGINE SOON BRAKE...
Page 10 Instrumentation Service engine soon Illuminates briefly to ensure the SERVICE system is functional. If it comes on ENGINE after the engine is started, one of SOON the engine’s emission control systems may be malfunctioning. The light may illuminate without a driveability concern being noted.
Page 11 Instrumentation Check fuel cap (if equipped) Illuminates when the fuel cap is not CHECK installed correctly. Check the fuel FUEL cap for proper installation. When the fuel filler cap is properly re-installed, the light(s) will turn off after a period of normal driving. Continuing to operate the vehicle with the fuel cap mis-installed can activate the Service Engine Soon/Check Engine warning light.
Page 12 Instrumentation Check gage (if equipped) Illuminates when the engine coolant CHECK temperature is high, the engine oil GAGE pressure is low or the fuel gauge is at or near empty. Refer to Engine coolant temperature gauge, Engine oil pressure gauge or Fuel gauge in this chapter for more information.
Page 13 Instrumentation Turn signal Illuminates when the turn signals or the hazard lights are turned on. If the lights stay on continuously or flash faster, check for a burned-out bulb. High beams Illuminates when the high beam headlamps are turned on. Low washer fluid (if equipped) Illuminates when the windshield washer fluid is low.
Page 14 Instrumentation O/D off Illuminates when the overdrive function has been turned OFF using the Transmission Control Switch (TCS) on the gearshift. If the light does not come on or the light flashes steadily, have your vehicle serviced as soon as possible, damage to the transmission could occur. Speed control Illuminates when the speed control is activated.
Page 15 Instrumentation GAUGES Standard instrument cluster gauges CHECK GAGE SERVICE ENGINE SOON DOOR BRAKE AJAR TRIP CHECK FUEL WASH Optional instrument cluster gauges HI TEMP LOW OIL SERVICE ENGINE SOON BRAKE Speedometer Indicates the current vehicle speed.
Page 16 Instrumentation Engine coolant temperature gauge Indicates the temperature of the engine coolant. At normal operating temperature, the needle remains within the normal area (the indicated area between the “H” and “C”). If it enters the red section, the engine is overheating. Stop the vehicle as soon as safely possible, switch off the engine immediately and let the engine cool.
Page 17 Instrumentation Trip odometer Registers the kilometers (miles) of individual journeys. • Standard instrument cluster Press and release the TRIP SELECT/RESET button to toggle between the odometer and trip odometer display. Press and hold the button to reset. • Optional instrument cluster Press and release the TRIP/RESET button to toggle between the odometer and trip odometer display.
Page 18 Instrumentation Engine oil pressure gauge Indicates engine oil pressure. At normal operating temperature, the needle will be in the normal range (the area between the “L” and “H”); if the needle goes below the normal range, stop the vehicle as soon as safely possible and switch off the engine immediately.
Page 19 Instrumentation Usually, when something affects the compass readings, the compass will correct itself after a few days of operating your vehicle in normal conditions. If the compass still appears to be inaccurate, a manual calibration may be necessary. Refer to Compass calibration adjustment.
Page 20 Instrumentation Compass calibration adjustment Perform this adjustment in an open area free from steel structures and high voltage lines: For optimum calibration, turn off all electrical accessories (heater/air conditioning, wipers, etc.) and make sure all vehicle doors are shut. 1. Start the vehicle. 2.
Page 21 Instrumentation Selectable features Reset Press this control to select and reset functions shown in the INFO menu and SETUP menu. Info menu This control displays the following control displays: • Odometer/Compass • Trip odometer/Odometer/Compass • Average Fuel Economy • Trip Elapsed Drive Time •...
Page 22 Instrumentation degrees between adjacent zones and will become noticeable as the vehicle crosses multiple zones. A correct zone setting will eliminate this error. Refer to Compass zone/calibration adjustment. Compass zone/calibration adjustment Perform this adjustment in an open area free from steel structures and high voltage lines.
Page 23 Instrumentation 9. Slowly drive the vehicle in a circle (less than 5 km/h [3 mph]) until the CIRCLE SLOWLY TO CALIBRATE indicator changes to CALIBRATION COMPLETED. This will take up to three circles to complete calibration. 10. The compass is now calibrated. Average fuel economy (AFE) Select this function from the INFO menu to display your average fuel...
Page 24 Instrumentation Trip elapsed drive time Select this function from the INFO menu to display a timer. To operate the Trip Elapsed Drive Time perform the following: 1. Press and release RESET in order to start the timer. 2. Press and release RESET to pause the timer. 3.
Page 25 Instrumentation Autolocks 1. Select this function from the SETUP control for the current display mode. 2. Press the RESET control to turn the autolocks ON or OFF. Easy entry/exit 1. Select this function from the SETUP control for the current display mode.
Page 26 Instrumentation Units (English/Metric) 1. Select this function from the SETUP menu for the current units to be displayed. 2. Press the RESET control to change from English to Metric. System check Selecting this function from the SETUP menu causes the message center to cycle through each of the systems being monitored.
Page 27 Instrumentation Warning messages that have been reset are divided into three categories: • They will reappear on the display every minute from the reset. • They will reappear on the display ten minutes from the reset. • They will not reappear until an ignition OFF-ON cycle has been completed.
Page 28 Instrumentation TRANSMISSION OVERHEATED. Indicates the transmission is overheating. This warning may appear when towing heavy loads or when driving in a low gear at a high speed for an extended period of time. Stop the vehicle as soon as safely possible, turn off the engine and let it cool.
Page 29 Instrumentation TIRE PRESSURE SYSTEM FAULT (if equipped). Displayed when the Tire pressure monitoring system is malfunctioning. If the warning stays on or continues to come on, have the system checked by your dealer. TIRE PRESSURE SENSOR FAULT (if equipped). Displayed when a Tire pressure sensor is malfunctioning.
Page 30 Instrumentation 2. Press and release the RESET control to display “OIL LIFE XX% HOLD RESET NEW”. 3. Press and hold the RESET control for 2 seconds to display “IF NEW OIL HOLD RESET”. 4. Press and hold the RESET control to display OIL LIFE SET TO 100%.
Page 31 Instrumentation TIRE PRESSURE SYSTEM OFF (if equipped). Displayed when the tire pressure monitoring system is turned off. Only your dealer can turn the system on or off. It is recommended that the tire pressure monitoring system is always turned ON. DATA ERR.
Page 32: Controls And Features
Controls and features HEADLAMP CONTROL Rotate the headlamp control clockwise to the first position to turn on the parking lamps. Rotate clockwise to the second position to also turn on the headlamps. Foglamp control (if equipped) The headlamp control also operates the foglamps.
Page 33: Controls And Features
Controls and features High beams Push the lever toward the instrument panel to activate. Pull the lever towards you to deactivate. Flash to pass Pull toward you slightly to activate and release to deactivate. PANEL DIMMER CONTROL Use to adjust the brightness of the instrument panel during headlamp parklamp operation.
Page 34 Controls and features AUTOLAMP CONTROL The autolamp system provides light sensitive automatic on-off control of the exterior lights normally controlled by the headlamp control. The autolamp system also keeps the lights on for approximately 20 seconds or a programmed time delay after the ignition switch is turned to the OFF position.
Page 35 Controls and features • the vehicle is moving in reverse at a speed of less than 5 km/h (3 mph) and a moving object is approaching the rear of the vehicle at a speed of less than 5 km/h (3 mph) The RSS is not effective at speeds greater than 5 km/h (3 mph) and may not detect certain angular or moving objects.
Page 36 Controls and features The RSS detects obstacles within approximately 1.8 meters (5.9 ft.) of the rear bumper with a decreased coverage area at the outer corners of the bumper, (refer to the figures for approximate zone coverage areas). As you move closer to the obstacle, the rate of the tone increases.
Page 37 Controls and features CLIMATE CONTROL SYSTEM Manual heating and air conditioning system (if equipped) Fan speed control Controls the volume of air circulated in the vehicle. Temperature control knob Controls the temperature of the airflow inside the vehicle. Mode selector control Controls the direction of the airflow to the inside of the vehicle.
Page 38 Controls and features Since the air conditioner removes considerable moisture from the air during operation, it is normal if clear water drips on the ground under the air conditioner drain while the system is working and even after you have stopped the vehicle. •...
Page 39 Controls and features • (Defrost)-Distributes outside air through the windshield defroster ducts. It can be used to clear ice or fog from the windshield. If the outside temperature is about 6°C (43°F) or higher, the air conditioner will automatically dehumidify the air to reduce fogging. (Note that the A/C indicator does not illuminate when this mode is selected.) For added customer comfort, the system will allow some airflow through the floor ducts in this mode.
Page 40 Controls and features Operating tips • In humid weather conditions, place the climate control system in before driving. This will reduce fogging on your windshield. Once the windshield has been cleared, operate the climate control system as desired. • To reduce humidity buildup inside the vehicle in cold weather conditions, don’t drive with the climate control system in the OFF or MAX A/C position.
Page 41 Controls and features 4. Set the fan speed to High 5. Direct the outer panel vents towards the side windows 6. To increase airflow to the outer panel vents, close the central panel vents. Do not place objects on top of the instrument panel, as these objects may become projectiles in a collision or sudden stop.
Page 42 Controls and features Turning the DEATC system on DUAL AUTO Press AUTO, any of the override controls, the fan speed control, or either of the temperature selection controls. The DEATC system will only operate when the ignition is in the ON position. Turning the DEATC system off Press OFF.
Page 43 Controls and features reduce window fogging. Additionally, if the engine is not warm enough to provide heat, the fan will operate at a low speed and the airflow will be directed to the windshield or to the floor. The fan speed will start to increase and the airflow location will change to the floor area.
Page 44 Controls and features Driver side temperature selection DUAL AUTO The display window indicates the selected temperature and manual control of fan speed ( ) if automatic fan speed is not desired. To control the temperature, select any temperature between 16°C (60°F) and 32°C (90°F) by pressing the temperature control on the driver side of the system.
Page 45 Controls and features Fan speed ( DUAL AUTO When AUTO is pressed, fan speed is adjusted automatically for existing conditions. You can override fan speed at any time. To control fan speed manually, press the fan control to cancel the automatic fan speed operation.
Page 46 Controls and features , if the outside temperature is about 6°C (43°F) or higher, the air conditioner will automatically dehumidify the air to reduce fogging. However, the A/C indicator will be off and the A/C override control cannot be selected. The air conditioning compressor can operate in all modes except OFF.
Page 47 Controls and features indicator will not be lit. If the recirculated air is selected while in AUTO operation, the DEATC system will be disabled and you will return to manual operation with the recirculated air indicator lit and with the A/C operating.
Page 48 Controls and features ducts. If the temperature is about 6°C (43°F) or higher, the air conditioner will automatically dehumidify the air to reduce fogging. (Note that the A/C indicator does not illuminate when this mode is selected.) Recirculation and A/C override controls cannot be selected. For added customer comfort, the air distributed through the floor ducts may be slightly warmer than the air sent to the windshield defroster ducts.
Page 49 Controls and features If the outside temperature is displayed while the DEATC system is in the OFF mode and the DEATC is turned on, the driver and passenger temperatures will be displayed for 4 seconds. Following this, the outside temperature display will return to the window. The outside temperature reading is most accurate when the vehicle is moving.
Page 50 Controls and features objects may fall down into the defroster outlets and block airflow, in addition to damaging the climate control system. To aide in side window defogging/demisting in cold weather conditions: 1. Select 2. Set the temperature control to full heat 3.
Page 51 Controls and features Front auxiliary control For the rear auxiliary climate controls to function, the front REAR auxiliary climate control must be set to REAR. To control the auxiliary climate control system from the front controls, turn the fan speed control knob to the desired speed.
Page 52 Controls and features Rear auxiliary climate controls (if equipped) The rear auxiliary climate controls are located in the headliner of the second row seating. Ensure that the front auxiliary control is turned to REAR to enable the rear climate controls. Turn the fan speed control to the desired fan speed.
Page 53 Controls and features Press the mode selector again to select air distribution through the floor vents. The icon will illuminate on the temperature selector. Only the auxiliary control head (front or rear) that is active will have the indicator lights functioning. Floor console climate controls (if equipped) Depending on the equipment package, your vehicle may be equipped with floor console climate control capabilities.
Page 54 Controls and features Mode selector control Controls the direction of the airflow to the rear of the vehicle. To select air flow from the panel registers of the console, slide the control to . To select airflow from the registers of the floor console, slide the control to To stop the air from flowing through the floor console: 1.
Page 55 Controls and features USING YOUR AUDIO SYSTEM Premium AM/FM Stereo/Cassette/Single CD DISC VOL PUSH ON FM 1 MUTE TAPE DOLBY B NR AUTO SEEK TUNE SCAN BASS TREB FADE SIDE 1-2 COMP SHUFFLE Volume/power control Press the control to turn the audio system on or off.
Page 56 Controls and features AM/FM select The AM/FM select control works in radio, tape and CD modes. AM/FM select in radio mode This control allows you to select AM or FM frequency bands. Press the control to switch between AM, FM1 or FM2 memory preset stations. AM/FM select in tape mode Press this control to stop tape play and begin radio play.
Page 57 Controls and features Seek function in CD mode • Press to seek to the previous track of the disc. If a selection has been playing for three seconds or more and you press , the CD will replay that selection from the beginning.
Page 58 Controls and features 3. Press and hold a memory preset control until the sound returns, indicating the station is held in memory on the control you selected. SIDE 1-2 COMP SHUFFLE Autoset memory preset Autoset allows you to set strong radio stations without losing your original manually set preset stations.
Page 59 Controls and features Press the BASS control then press: • to decrease the bass output • to increase the bass output. Treble adjust The treble adjust control allows you BASS TREB to increase or decrease the audio system’s treble output. Press the TREB control then press: •...
Page 60 Controls and features Speaker fade adjust Speaker sound can be adjusted FADE between the front and rear speakers. Press the FADE control then press: • to shift the sound to the front and • to shift the sound to the rear. Tape/CD select •...
Page 61 Controls and features Fast forward The fast forward control works in tape and CD modes. • In the tape mode, tape direction will automatically reverse when the end of the tape is reached. • In CD mode, pressing the control fast forwards the CD within the current track.
Page 62 Controls and features Compression adjust Compression adjust brings soft and COMP loud CD passages together for a more consistent listening level. Press the COMP control to activate and deactivate compression adjust. Shuffle feature The shuffle feature operates in CD SHUFFLE mode and plays all tracks in random order.
Page 63 Controls and features • to decrease minutes and • to increase minutes. If your vehicle has a separate clock, (other than the digital radio display), the CLK control will not function in the above manner. The CLK control will allow you to switch between media display mode AUTO (radio station, stereo information,...
Page 64 Controls and features Audiophile AM/FM Stereo In Dash Six CD Radio Volume/power control Press the control to turn the audio system on or off. Turn the control to raise or lower volume. PUSH ON If the volume is set above a certain level and the ignition is turned off, the volume will come back on at a “nominal”...
Page 65 Controls and features • to increase volume compensation. • to decrease or shut off the volume compensation. The selected level will appear in the display. AM/FM select The AM/FM select control works in radio and CD modes. AM/FM select in radio mode This control allows you to select AM or FM frequency bands.
Page 66 Controls and features Seek function in radio mode • Press to find the next listenable station down the frequency band. SEEK DOWN will display. • Press to find the next listenable station up the frequency band. SEEK UP will display. Seek function in CD mode •...
Page 67 Controls and features 2. Press the SEEK control to access the next listenable station up or down the frequency band. Press the TUNE control to go up or down the listening band in individual increments. 3. Select a station. Refer to Seek function for more information on selecting a station.
Page 68 Controls and features CD select CD mode may be entered by pressing the CD control and the LOAD control. Load the CD into the audio system. The first track of the disc will begin playing. After that, CD play will begin where it stopped last.
Page 69 Controls and features Press the LOAD control. (You can choose which slot will be loaded by pressing the desired preset number. If you do not choose a slot, the system will choose the next available one.) Wait until the CD door opens. Load the CD into the player.
Page 70 Controls and features Rewind The rewind control works in CD modes. Press and hold the REW control until the desired selection is reached. If the beginning of the disc is reached, the CD will begin play at the first track. Release the control to disengage rewind mode.
Page 71 Controls and features Treble adjust The treble adjust control allows you BASS to increase or decrease the audio system’s treble output. TREB Press the TREB control. Use the SEL control to increase or decrease the amount of treble. Speaker balance adjust Speaker sound distribution can be adjusted between the right and left speakers.
Page 72 Controls and features • RDS ON— Refer to Radio data system feature. • SELECT HOURS — Refer to Setting the clock. • SELECT MINUTES —Refer to Setting the clock. When in CD mode, you can access: SELECT HOURS, SELECT MINUTES or COMP ON/OFF.
Page 73 Controls and features RDS traffic scan feature When in traffic mode, you can use the SCAN feature to scan up the frequency band for listenable traffic capable frequencies. With the RDS activated, press the MENU control until TRAFFIC ON is displayed.
Page 74 Controls and features Program type This feature allows you to search for RDS stations selectively by their program type. Press the MENU control until FIND program type is displayed. MENU Use the SEL control to select the program type. With the feature on, use the SEEK or SCAN control to find the desired program type from the following selections: •...
Page 75 Controls and features Press the DSP control to access one of the following modes: • DSP OFF • SIGNAL MODE • OCCUPANCY MODE Use the SEL control to select the desired signal mode (the selected mode will appear in the display). The following signal modes can be selected: •...
Page 76 Controls and features Use the SEL control to manually set the time. • Press to increase hours/minutes. • Press to decrease hours/minutes. Press the MENU control again to disengage the clock mode. Troubleshooting the CD changer (if equipped) The laser beam used in the compact disc player is harmful to the eyes.
Page 77 Controls and features CD units are designed to play commercially pressed 12 cm (4.75 in) audio compact discs only. Due to technical incompatibility, certain recordable and re-recordable compact discs may not function correctly when used in Ford CD players. Irregular shaped CDs, CDs with a scratch protection film attached, and CDs with homemade paper (adhesive) labels should not be inserted into the CD player.
Page 78 Controls and features Radio reception factors Three factors can affect radio reception: • Distance/strength. The further an FM signal travels, the weaker it is. The listenable range of the average FM station is approximately 40 km (24 miles). This range can be affected by “signal modulation.” Signal modulation is a process radio stations use to increase their strength/volume relative to other stations.
Page 79 Controls and features POSITIONS OF THE IGNITION 1. OFF/LOCK, shuts off the engine and all accessories/locks the steering wheel, gearshift lever and allows key removal. 2. ACC, allows the electrical accessories such as the radio to operate while the engine is not running.
Page 80 Controls and features To turn speed control off • Press OFF • Speed control automatically defaults to OFF when the ignition is turn off. Once speed control is switched off, the previously programmed set speed will be erased. To set a speed •...
Page 81 Controls and features To set a higher set speed • Press and hold SET +. Release the control when the desired vehicle speed is reached or • Press and release SET + to operate the Tap-Up function. Each press will increase the set speed by 1.6 km/h (1 mph) or COAST •...
Page 82 Controls and features To disengage speed control • Depress the brake pedal. Disengaging the speed control will not erase the previously programmed set speed. Pressing OFF will erase the previously programmed set speed. To return to a previously set speed •...
Page 83 Controls and features Indicator light This light comes on when the vehicle speed control is engaged and actively controlling vehicle speed. TILT/TELESCOPE STEERING COLUMN (IF EQUIPPED) Pull the lever down to unlock the tilt/telescope steering column. While the lever is in the down position, tilt and telescope the steering column to the desired orientation.
Page 84 Controls and features HAZARD FLASHER For information on the hazard flasher control, refer to Hazard flasher in the Roadside emergencies chapter. WINDSHIELD WIPER/WASHER CONTROLS Rotate the windshield wiper control to the desired interval, low or high speed position. The bars of varying length are for intermittent wipers.
Page 85 Controls and features STEERING WHEEL CONTROLS (IF EQUIPPED) These controls allow you to operate some radio and climate control features. Audio control features Press to select: • AM, FM1, FM2, • TAPE (if equipped), • CD (if equipped), or • DVD (if equipped). In AM, FM1, or FM2 mode: •...
Page 86 Controls and features Climate control features Press TMP + or - to adjust temperature. Press + or - to adjust fan speed. OVERHEAD CONSOLE (IF EQUIPPED) The appearance of your vehicle’s overhead console will vary according to your option package. Storage compartment Press the latch to open the storage compartment.
Page 87 Controls and features Installing a garage door opener (if equipped) The storage compartment can be converted to accommodate a variety of aftermarket garage door openers: • Place the Velcro hook onto the side of the aftermarket transmitter opposite of the button.
Page 88 Controls and features To close the moon roof: Press and hold the front portion of the control until the glass panel stops moving. Once fully closed, the rear of the glass panel will appear higher than the front edge. To vent: To tilt the moon roof into the vent position (when the glass panel is closed), press and hold the front portion of the control.
Page 89 Controls and features All vehicles are equipped with a cargo lamp, which is located overhead in the rear cargo area and above the the third row seat (if equipped). The cargo lamp will stay on if the control is moved to the passenger side position.
Page 90 Controls and features Retain the original transmitter for use in other vehicles as well as for future programming procedures (i.e. new HomeLink equipped vehicle purchase). It is also suggested that upon the sale of the vehicle, the programmed Homelink Universal Transceiver buttons be erased for security purposes, refer to Programming in this section.
Page 91 Controls and features 5. Press and hold the just-trained HomeLink button and observe the red light. If the light is a constant red, programming is complete and your device should activate when the HomeLink button is pressed and released. Note: To program the remaining two HomeLink buttons, begin with step 2 in the “Programming”...
Page 92 Controls and features Gate Operator & Canadian Programming During programming, your hand-held transmitter may automatically stop transmitting — not allowing enough time for HomeLink to accept the signal from the hand-held transmitter. After completing steps 1 and 2 outlined in the “Programming” section, replace step 3 with the following: Note: If programming a garage door opener or gate operator, it is...
Page 93 Controls and features Erasing HomeLink buttons To erase the three programmed buttons (individual buttons cannot be erased): • Press and hold the two outer HomeLink buttons until the red indicator light begins to flash-after 20 seconds. Release both buttons. Do not hold for longer that 30 seconds.
Page 94 Controls and features ILLUMINATED VISOR MIRROR (IF EQUIPPED) To turn on the visor mirror lamps, lift the mirror cover. POWER WINDOWS Press and hold the rocker switches to open and close windows. • Press the top portion of the rocker switch to close. AUTO •...
Page 95 Controls and features One touch down • Press AUTO completely down and release quickly. The driver’s window will open fully. One touch down can be deactivated during operation by pushing down on the top part of the driver power AUTO window control.
Page 96 Controls and features POWER DOOR LOCKS Press control to unlock all doors. Press control to lock all doors. POWER DOOR LOCK/UNLOCK INHIBIT If the interior trim switch does not operate, see the Perimeter alarm system in this section for more details.
Page 97 Controls and features CHILDPROOF DOOR LOCKS When these locks are set, the rear doors cannot be opened from the inside. The rear doors can be opened from the outside when the doors are unlocked. The childproof locks are located on rear edge of each rear door and must be set separately for each door.
Page 98 Controls and features Heated outside mirrors (if equipped) Both mirrors are heated automatically to remove ice, mist and fog when the rear window defrost is activated. Do not remove ice from the mirrors with a scraper or attempt to readjust the mirror glass if it is frozen in place.
Page 99 Controls and features Auxiliary power point Power outlets are designed for accessory plugs only. Do not hang any type of accessory or accessory bracket from the plug. Improper use of the power outlet can cause damage not covered by your warranty. The power point is an additional power source for electrical accessories.
Page 100 Controls and features POSITIVE RETENTION FLOOR MAT Position the driver floor mat so that the eyelet is over the pointed end of the retention post and rotate forward to lock in. Make sure that the mat does not interfere with the operation of the accelerator or the brake pedal.
Page 101 Controls and features Make sure the liftgate door and/or window are closed to prevent exhaust fumes from being drawn into the vehicle. This will also prevent passengers and cargo from falling out. CARGO COVER (IF EQUIPPED) Your vehicle may be equipped with a cargo area cover that covers the luggage compartment of your vehicle.
Page 102 Controls and features 7 passenger stowage: 1. To open, lift the release handle and the lid. 2. To close, lower the lid, lift the release handle and press down on the lid. 5 passenger stowage: When the lid is open, it will stand up on its own.
Page 103 Controls and features Unlocking the doors/liftgate Press this control to unlock the driver’s door. The interior lamps will illuminate with the ignition OFF. Press the control a second time within three seconds to unlock all doors and liftgate. Locking the doors/liftgate Press this control to lock all doors and liftgate.
Page 104 Controls and features Opening the liftgate window Press the control to unlatch the liftgate window. Sounding a panic alarm Press this control to activate the alarm. The personal panic alarm will cycle the horn and turn signals on/off, plus illuminate the interior lights. To deactivate the alarm, press the control again or turn the ignition to ACC or ON.
Page 105 Controls and features Activating the memory seat feature To activate this feature: 1. Position the seat to the position you desire. 2. Press the SET control on the driver’s door panel. 3. Within 5 five seconds, press one control on the remote transmitter and then press the 1 or 2 control on the driver’s door panel to which you would like to associate with the seat...
Page 106 Controls and features To replace the battery: 1. Twist a thin coin between the two halves of the transmitter near the key ring. DO NOT TAKE THE FRONT PART OF THE TRANSMITTER APART. 2. Place the positive (+) side of new battery in the same orientation.
Page 107 Controls and features Programming remote transmitters It is necessary to have all (maximum of four — original and/or new) of your remote transmitters available prior to beginning this procedure. To program the transmitters yourself: • Insert a key in the ignition and turn from 1 (LOCK) to 3 (ON) and cycle between 1 (LOCK) and 3 (ON) eight times in rapid...
Page 108 Controls and features KEYLESS ENTRY SYSTEM (IF EQUIPPED) With the keyless entry keypad, you can: • lock or unlock the vehicle doors and liftgate without using the key. • open the liftgate window. • disable/enable autolock. • arm and disarm the perimeter alarm system (if equipped).
Page 109 Controls and features Programming your own personal entry code 1. Enter the factory-set code (keypad will illuminate when pressed). 2. Press the 1/2 control within five seconds of step 1. 3. Enter your personal 5 digit code. Enter each digit within five seconds of the previous one.
Page 110 Controls and features Erasing personal code 1. Enter the factory-set code. 2. Press 1/2 within five seconds of step 1 and release. 3. Press the 1/2 control and hold for 2 seconds to erase the customer programmed keycode, within five seconds of step 2.
Page 111 Controls and features Unlocking the doors and liftgate or the liftgate window with the keyless entry system The driver’s door must be unlocked before any other. If more than five seconds pass between pressing numbers, enter the code again. The system has shut down if the keypad light is out.
Page 112 Controls and features Locking the doors and liftgate, press the 7/8 and 9/0 controls at the same time. This can be done only when the driver’s door is closed. Autolock The autolock feature will lock all of the vehicle doors when: •...
Page 113 Controls and features Power door unlock/lock procedure You must complete steps 1-5 within 30 seconds or the procedure will have to be repeated. If the procedure needs to be repeated, you must wait 30 seconds. 1. Turn the ignition key to ON. 2.
Page 114 Controls and features PERIMETER ALARM SYSTEM The perimeter anti-theft system will help prevent your vehicle from unauthorized entry. If there is any potential perimeter anti-theft problem with your vehicle, ensure ALL remote entry transmitters are brought to the dealership, to aid in troubleshooting. PERIMETER ALARM SYSTEM (IF EQUIPPED) The perimeter anti-theft system will help prevent your vehicle from unauthorized entry.
Page 115 Controls and features Arming the system When armed, this system will help protect your vehicle from unauthorized entry. When unauthorized entry occurs, the system will flash the headlamps and/or parking lamps, and will chirp the horn. The system is ready to arm whenever the key is removed from the ignition.
Page 116 Controls and features Disarming the system You can disarm the system by any of the following actions: • Unlock the doors by using your remote entry transmitter. • Unlock the doors by using your keyless entry pad. • Unlock the driver’s door with a key. Turn the key full travel (toward the front of the vehicle) to make sure the alarm disarms.
Page 117 Controls and features • Press the PANIC control on the remote entry transmitter. This will only shut off the horn and parking lamps when the alarm is sounding. The alarm system will still be armed. • Press the liftgate window control on the remote entry transmitter.
Page 118 Controls and features THEFT INDICATOR The theft indicator is the flashing red indicator located on top of the instrument panel. • When the ignition is in the OFF position, the indicator will flash once every 2 seconds to indicate the SecuriLock system is functioning as a theft deterrent.
Page 119 OFF and restart the engine with all other objects on the key ring held away from the ignition key. Check to make sure the coded key is an approved Mercury coded key. If your keys are lost or stolen you will need to do the following: •...
Page 120 Controls and features 1. Insert the first previously programmed coded key into the ignition and turn the ignition from 2 (ACC) to 3 (ON) (maintain ignition in 3 (ON) for at least one second). 2. Turn ignition to 1 (LOCK) and remove the first coded key from the ignition.
Page 121: Seating And Safety Restraints
Seating and safety restraints SEATING Front seat Adjustable head restraints (if equipped) Your vehicle’s front seats are equipped with head restraints which are vertically adjustable. The purpose of these head restraints is to help limit head motion in the event of a rear collision. To properly adjust your head restraints, lift the head restraint so that it is located directly behind your head or as close to that position as possible.
Page 122: Seating And Safety Restraints
Seating and safety restraints Do not pile cargo higher than the seatbacks to reduce the risk of injuring people in a collision or sudden stop. Always drive and ride with your seatback upright and the lap belt snug and low across the hips. Reclining the seatback can cause an occupant to slide under the seat’s safety belt, resulting in severe personal injuries in the event of a collision.
Page 123 Seating and safety restraints Always drive and ride with your seatback upright and the lap belt snug and low across the hips. Reclining the seatback can cause an occupant to slide under the seat’s safety belt, resulting in severe personal injuries in the event of a collision.
Page 124 Seating and safety restraints Press the control to move the seat forward, backward, up or down. Memory seat/easy entry/exit feature (if equipped) This system allows automatic positioning of the driver seat to three programmable positions. The memory seat control is located on the driver door.
Page 125 Seating and safety restraints Using the manual lumbar support (if equipped) Turn the lumbar support control toward the front of vehicle to move the lumbar support forward for more direct support. Turn the lumbar support control toward the rear of vehicle to move the lumbar support back for less direct support.
Page 126 Seating and safety restraints REAR SEATS Adjustable head restraints Your vehicle’s rear seats may be equipped with head restraints which are vertically adjustable. The purpose of these head restraints is to help limit head motion in the event of a rear collision. To properly adjust your head restraints, lift the head restraint so that it is located directly behind your head or as close to that position as possible.
Page 127 Seating and safety restraints 1. Press the lower release control downward to unlatch the seatback. 2. Rotate the seatback downward into the load floor position. 3. Press down on the top outboard area of the seatback until a click is heard.
Page 128 Seating and safety restraints To return the seat to the upright position: • Press downward on the upper corner of the seatback and hold. • Pull the release handle upward to unlatch the seat. • Rotate the seatback upward until the seatback latches in the upright position.
Page 129 Seating and safety restraints Adjusting the 2nd row seat for E-Z Entry (if equipped) The E-Z Entry seat allows for easier entry and exit to and from the 3rd row seat. To enter the 3rd row seat: 1. Fold down the 2nd row seat. 2.
Page 130 Seating and safety restraints To exit the 3rd row seat, pull the red access control lever up releasing the seat from the floor and rotate the seat up towards the front seat. Always latch the vehicle seat to the floor, whether the seat is occupied or empty.
Page 131 Seating and safety restraints Folding the middle 2nd row seat (If equipped) 1. Locate the lever on the side of the seatback. 2. Pull the lever up and push the seatback toward the front of the vehicle. 3. Press down on the top outboard area of the seatback until a click is heard.
Page 132 Seating and safety restraints Second row center seat storage space (if equipped) Storage space is provided underneath the 40/20/40 second row center seat. To access the storage space pull up on the strap. Third row seat (if equipped) 3rd row stow feature The 3rd row seat has a tip/stow feature to increase cargo space without removing the seat from the vehicle.
Page 133 Seating and safety restraints 3. Push the closeout panel forward over the space between the seats. To put seat in upright position: 1. Pull back the slider panel on the seatback to release the closeout panel. 2. Pull the seat release lever located on top of the seatback while lifting the seatback into the upright position.
Page 134 Seating and safety restraints SAFETY RESTRAINTS Personal Safety System The Personal Safety System provides an improved overall level of frontal crash protection to front seat occupants and is designed to help further reduce the risk of air bag-related injuries. The system is able to analyze different occupant conditions and crash severity before activating the appropriate safety devices to help better protect a range of occupants in a variety of frontal crash situations.
Page 135 Seating and safety restraints common, moderate-severity impacts. A higher energy level is used for the most severe impacts. Refer to Air bag Supplemental Restraints section in this chapter. Front crash severity sensor The front crash severity sensor enhances the ability to detect the severity of an impact.
Page 136 Seating and safety restraints to the Warning Light section in the Instrument Cluster chapter. Routine maintenance of the Personal Safety System is not required. The Restraints Control Module (RCM) monitors its own internal circuits and the circuits for the air bag supplemental restraints, crash sensor(s), safety belt pretensioners, front safety belt buckle sensors, and the driver seat position sensor.
Page 137 Seating and safety restraints In a rollover crash, an unbelted person is significantly more likely to die than a person wearing a safety belt. Each seating position in your vehicle has a specific safety belt assembly which is made up of one buckle and one tongue that are designed to be used as a pair.
Page 138 Seating and safety restraints Combination lap and shoulder belts 1. Insert the belt tongue into the proper buckle (the buckle closest to the direction the tongue is coming from) until you hear a snap and feel it latch. Make sure the tongue is securely fastened in the buckle.
Page 139 Seating and safety restraints Automatic locking mode In this mode, the shoulder belt is automatically pre-locked. The belt will still retract to remove any slack in the shoulder belt. The automatic locking mode is not available on the driver safety belt. When to use the automatic locking mode •...
Page 140 Seating and safety restraints After any vehicle collision, all passenger seat belt systems must be checked by a qualified technician to verify that the “automatic locking retractor” feature for child seats is still functioning properly. In addition, all seat belts should be checked for proper function.
Page 141 Seating and safety restraints Insert the tongue into the correct buckle (the buckle closest to the direction the tongue is coming from). To lengthen the belt, turn the tongue at a right angle to the belt and pull across your lap until it reaches the buckle.
Page 142 Seating and safety restraints • 2nd row center seating position — 40/20/40 The lap belt will adjust automatically. To fasten, grasp the tongue, and with a continuous motion, pull out enough webbing to buckle the tongue into the correct buckle. If you did not pull out enough webbing to reach the buckle, allow the tongue to retract fully before trying to pull it out...
Page 143 Seating and safety restraints When the safety canopy system and the front airbags are activated, the safety belt pretensioners for the driver and right front passenger seating positions will be activated when the respective seatbelt is properly buckled. The driver and the right front passenger seat belt system (including retractors, buckles and height adjusters) must be replaced if the vehicle is involved in a collision that results in deployment of front air bags and safety belt pretensioners.
Page 144 Seating and safety restraints Do not use extensions to change the fit of the shoulder belt across the torso. Safety belt warning light and indicator chime The seat belt warning light illuminates in the instrument cluster and a chime sounds to remind the occupants to fasten their safety belts. Conditions of operation If...
Page 145 Seating and safety restraints If... Then... The driver’s safety belt is not The BeltMinder feature is activated - buckled before the vehicle has the safety belt warning light reached at least 5 km/h (3 illuminates and the warning chime mph) and 1-2 minutes have sounds for 6 seconds every 30 elapsed since the ignition seconds, repeating for approximately...
Page 146 Seating and safety restraints If... Then... The driver’s seat belt is The BeltMinder feature will not buckled before the ignition activate. switch is turned to the ON position... The purpose of the BeltMinder is to remind occasional wearers to wear safety belts all of the time.
Page 147 Seating and safety restraints Reasons given... Consider... “The people I’m Set the example, teen deaths occur 4 times more with don’t wear often in vehicles with TWO or MORE people. belts” Children and younger brothers/sisters imitate behavior they see. “I have an air bag” Air bags offer greater protection when used with safety belts.
Page 148 Seating and safety restraints To reduce the risk of injury, do not deactivate/activate the Belt Minder feature while driving the vehicle. 1. Turn the ignition switch to the RUN (or ON) position. (DO NOT START THE ENGINE) 2. Wait until the safety belt warning light turns off. (Approximately 1–2 minutes) •...
Page 149 Seating and safety restraints Before following the procedure, make sure that: • the parking brake is set • the gearshift is in P (Park) (automatic transmission) or the neutral position (manual transmission) • the ignition switch is in the OFF position •...
Page 150 Seating and safety restraints 9. After receiving confirmation, the deactivation/activation procedure is complete. Safety belt maintenance Inspect the safety belt systems periodically to make sure they work properly and are not damaged. Inspect the safety belts to make sure there are no nicks, tears or cuts. Replace if necessary. All safety belt assemblies, including retractors, buckles, front seat belt buckle assemblies, buckle support assemblies (slide bar-if equipped), shoulder belt height adjusters (if equipped), shoulder belt guide on seatback (if...
Page 151 Seating and safety restraints event of a collision this module may save information related to the collision including information about the air bag system and impact severity. This information will assist Ford Motor Company in servicing the vehicle and in helping to better understand real world collisions and further improve the safety of future vehicles.
Page 152 Do not attempt to service, repair, or modify the air bag supplemental restraint systems or its fuses. See your Ford or Lincoln Mercury dealer. Modifications to the front end of the vehicle, including frame, bumper, front end body structure and non-Ford tow hooks may effect the performance of the air bag sensors increasing the risk of injury.
Page 153 Seating and safety restraints Children and air bags For additional important safety information, read all information on safety restraints in this guide. Children must always be properly restrained. Accident statistics suggest that children are safer when properly restrained in the rear seating positions than in the front seating position.
Page 154 Seating and safety restraints The air bags inflate and deflate rapidly upon activation. After air bag deployment, it is normal to notice a smoke-like, powdery residue or smell the burnt propellant. This may consist of cornstarch, talcum powder (to lubricate the bag) or sodium compounds (e.g., baking soda) that result from the combustion process that inflates the...
Page 155 Seating and safety restraints • diagnostic module. • and the electrical wiring which connects the components. The diagnostic module monitors its own internal circuits and the supplemental air bag electrical system warning (including the impact sensors), the system wiring, the air bag system readiness light, the air bag back up power and the air bag ignitors.
Page 156 A, B, or C pillar trim, or the headliner on a vehicle containing a Safety Canopy . See your Ford or Lincoln Mercury dealer. All occupants of the vehicle including the driver should always wear their safety belts even when an air bag SRS and Safety Canopy system is provided.
Page 157 Seating and safety restraints • The same warning light, electronic control and diagnostic unit as used for the front airbags. • Two side crash sensors mounted at the base of the B-pillar (one on each side). • Two side crash sensors located at the c-pillar behind the rear doors (one on each side).
Page 158 Seating and safety restraints Several Safety Canopy system components get hot after inflation. Do not touch them after inflation. If the Safety Canopy system has deployed, the Safety Canopy will not function again. The Safety Canopy system (including the A, B and C pillar trim) must be inspected and serviced by a qualified technician in accordance with the vehicle service manual.
Page 159 Seating and safety restraints SAFETY RESTRAINTS FOR CHILDREN See the following sections for directions on how to properly use safety restraints for children. Also see Air bag supplemental restraint system (SRS) in this chapter for special instructions about using air bags. Important child restraint precautions You are required by law to use safety restraints for children in the U.S.
Page 160 Seating and safety restraints Child booster seats Children outgrow a typical convertible or toddler seat when they weigh 40 pounds and are around 4 years of age. Although the lap/shoulder belt will provide some protection, these children are still too small for lap/shoulder belts to fit properly, which could increase the risk of serious injury.
Page 161 Seating and safety restraints Types of booster seats There are two types of belt-positioning booster seats: • Those that are backless. If your backless booster seat has a removable shield, remove the shield and use the lap/shoulder belt. If a seating position has a low seat back and no head restraint, a backless booster seat may place your child’s head (top...
Page 162 Seating and safety restraints Follow all instructions provided by the manufacturer of the booster seat. Never put the shoulder belt under a child’s arm or behind the back because it eliminates the protection for the upper part of the body and may increase the risk of injury or death in a collision. Never use pillows, books, or towels to boost a child.
Page 163 Seating and safety restraints When installing a child safety seat: • Review and follow the information presented in the Air bag supplemental restraint system (SRS) section in this chapter. • Use the correct safety belt buckle for that seating position (the buckle closest to the direction the tongue is coming from).
Page 164 Seating and safety restraints Installing child safety seats in combination lap and shoulder belt seating positions Air bags can kill or injure a child in a child seat. NEVER place a rear-facing child seat in front of an active air bag. If you must use a forward-facing child seat in the front seat, move the seat all the way back.
Page 165 Seating and safety restraints 3. While holding the shoulder and lap belt portions together, route the tongue through the child seat according to the child seat manufacturer’s instructions. Be sure the belt webbing is not twisted. 4. Insert the belt tongue into the proper buckle (the buckle closest to the direction the tongue is coming from) for that seating position until...
Page 166 Seating and safety restraints 7. Pull the lap belt portion across the child seat toward the buckle and pull up on the shoulder belt while pushing down with your knee on the child seat. 8. Allow the safety belt to retract to remove any slack in the belt.
Page 167 Seating and safety restraints 5. If you have not pulled out enough webbing to reach, allow the webbing to fully retract before attempting to pull it out again and repeat steps 2 through 4. 6. Pull the webbing through the child seat toward the retractor while pushing down with your knee on the child seat.
Page 168 Seating and safety restraints Attach the tether strap only to the appropriate tether anchor as shown. The tether strap may not work properly if attached somewhere other than the correct tether anchor. 1. Position the child safety seat on the rear seat cushion. 2.
Page 169 Seating and safety restraints • At the rear of the cargo area 4. Clip the tether strap to the anchor. If the tether strap is clipped incorrectly, the child safety seat may not be retained properly in the event of a collision. 5.
Page 170 Starting PREPARING TO START YOUR VEHICLE Engine starting is controlled by the powertrain control system. This system meets all Canadian Interference-Causing Equipment standard requirements regulating the impulse electrical field strength of radio noise. When starting a fuel-injected engine, avoid pressing the accelerator before or during starting.
Page 171 Starting • Make sure the parking brake is set. • Make sure the gearshift is in P (Park). 3. Turn the key to 3 (ON) without turning the key to 4 (START).
Page 172 Starting HI TEMP LOW OIL SERVICE ENGINE SOON BRAKE Make sure the corresponding lights illuminate or illuminate briefly. If a light fails to illuminate, have the vehicle serviced. • If the driver’s safety belt is fastened, the light may not illuminate. STARTING THE ENGINE Note: Whenever you start your vehicle, release the key as soon as the engine starts.
Page 173 Starting summer grade ethanol is used in cold weather conditions, you may experience increased cranking times, rough idle or hesitation until the engine has warmed up. Consult your fuel distributor for the availability of winter grade ethanol. Do not crank the engine for more than 30 seconds at a time as starter damage may occur.
Page 174 Starting To prevent electrical shock, do not use your heater with ungrounded electrical systems or two-pronged (cheater) adapters. Guarding against exhaust fumes Although odorless and colorless, carbon monoxide is present in exhaust fumes. Take precautions to avoid its dangerous effects. If you ever smell exhaust fumes of any kind inside your vehicle, have your dealer inspect and fix your vehicle immediately.
Page 175 Driving BRAKES Your service brakes are self-adjusting. Refer to the scheduled maintenance guide for scheduled maintenance. Occasional brake noise is normal and often does not indicate a performance concern with the vehicle’s brake system. In normal operation, automotive brake systems may emit occasional or intermittent squeal or groan noises when the brakes are applied.
Page 176: Driving
Driving The ABS operates by detecting the onset of wheel lockup during brake applications and compensates for this tendency. The wheels are prevented from locking even when the brakes are firmly applied. The accompanying illustration depicts the advantage of an ABS equipped vehicle (on bottom) to a non-ABS equipped vehicle (on top) during hard braking with loss of front braking traction.
Page 177 Driving maximizes the amount of brake booster assist, helping the driver to achieve maximum braking pressure. Once a panic brake application is detected, the system will remain activated as long as the brake pedal is depressed. The system is deactivated by releasing the brake pedal. When the system activates, the brake pedal will travel with very little effort;...
Page 178 Driving Pull the release lever to release the brake. Driving with the parking brake on will cause the brakes to wear out quickly and reduce fuel economy. ADVANCETRAC STABILITY ENHANCEMENT SYSTEM (IF EQUIPPED) The AdvanceTrac system provides a stability enhancement feature as well as a traction enhancement feature.
Page 179 Driving Driving conditions which may activate AdvanceTrac include: • Taking a turn too fast • Maneuvering quickly to avoid an accident, pedestrian or obstacle • Hitting a patch of ice • Changing lanes on a snow-rutted road • Entering a snow-free road from a snow-covered side street, or vice versa •...
Page 180 Driving spin. If your vehicle seems to lose engine power while driving in deep sand or very deep snow, switching off the AdvanceTrac stability enhancement feature will restore full engine power and will enhance momentum through the obstacle. Some drivers may notice a slight movement of the brake pedal when the AdvanceTrac performs a system self-check.
Page 181 Driving STEERING Your vehicle is equipped with power steering. Power steering uses energy from the engine to decrease the driver’s effort in steering the vehicle. To prevent damage to the power steering pump: • Never hold the steering wheel to the extreme right or the extreme left for more than a few seconds when the engine is running.
Page 182 Driving Loaded vehicles, with a higher center of gravity, may handle differently than unloaded vehicles. Extra precautions, such as slower speeds and increased stopping distance, should be taken when driving a heavily loaded vehicle. Your vehicle has the capability to haul more cargo and people than most passenger cars.
Page 183 Driving 3. Rotate the access panel (counterclockwise) with a flat head screw driver until it is lined up to the access hole in the open position. 4. Insert a tool (or screw driver) into the access hole to override the brake-shift interlock.
Page 184 Driving If your vehicle gets stuck in mud or snow it may be rocked out by shifting between forward and reverse gears, stopping between shifts, in a steady pattern. Press lightly on the accelerator in each gear. Do not rock the vehicle if the engine is not at normal operating temperature or damage to the transmission may occur.
Page 185 Driving P (Park) To put your vehicle in gear, start the engine, depress the brake pedal, then move gearshift lever out of P (Park). Always come to a complete stop before shifting into P (Park). Make sure the gearshift lever is securely latched in P (Park).
Page 186 Driving Drive (overdrive deactivated) Activate by pressing the transmission control switch on the end of the gearshift lever with the gearshift in the D(Drive) position. The transmission, with overdrive off, operates in gears one through four, providing more engine braking than D(Drive) with Overdrive ON and is useful whenever driving conditions (i.e., city traffic, hilly terrain, etc.) cause the transmission to excessively shift between D (Overdrive) and other gears.
Page 187 Driving Forced Downshifts To gain acceleration in (Overdrive) or Drive (O/D OFF) when passing another vehicle, push the accelerator to the floor. The transmission will downshift to the appropriate gear: fourth, third, second or first gear. ALL WHEEL DRIVE (AWD) SYSTEM (IF EQUIPPED) Your vehicle is equipped with a full-time All Wheel Drive (AWD) transfer case.
Page 188 Driving You should either know the terrain or examine maps of the area before driving. Map out your route before driving in the area. To maintain steering and braking control of your vehicle, you must have all four wheels on the ground and they must be rolling, not sliding or spinning. Basic operating principles •...
Page 189 Driving Always set the parking brake fully and make sure the gearshift is latched in P (Park). Turn the ignition to the LOCK position and remove the key whenever you leave your vehicle. If the parking brake is fully released, but the brake warning lamp remains illuminated, the brakes may not be working properly.
Page 190 Driving AWD Systems (if equipped) AWD uses all four wheels to power the vehicle. This increases traction, enabling you to drive over terrain and road conditions that a conventional two-wheel drive vehicle can’t. Sand When driving over sand, try to keep all four wheels on the most solid area of the trail.
Page 191 Driving Driving through deep water may damage the transmission. If the front or rear axle is submerged in water, the axle lubricant should be replaced. After driving through mud, clean off residue stuck to rotating driveshafts and tires. Excess mud stuck on tires and rotating driveshafts causes an imbalance that could damage drive components.
Page 192 Driving Descend a hill in the same gear you would use to climb up the hill to avoid excessive brake application and brake overheating. Do not descend in neutral, disengage overdrive or manually shift to a lower gear. When descending a steep hill, avoid sudden hard braking as you could lose control.
Page 193 If you have questions regarding tire replacement, see an authorized Ford or Lincoln Mercury dealer. If you nevertheless decide to equip your AWD for off-road use with tires larger than what Ford Motor Company recommends, you should not use these tires for highway driving.
Page 194 Driving Each day before you drive, check your tires. If one looks lower than the others, use a tire gauge to check pressure of all tires, and adjust if required. Check tire pressure with a tire gauge every few weeks (including spare).
Page 195 Driving LIMITED-SLIP AXLE (IF EQUIPPED) This axle provides added traction on slippery surfaces, particularly when one wheel is on a poor traction surface. Under normal conditions, the limited slip axle functions like a standard rear axle. Extended use of other than the manufacturer’s specified size tires on a limited slip rear axle could result in a permanent reduction in effectiveness.
Page 196 Driving • Maximum Trailer Weight: Maximum weight of a trailer the loaded vehicle (including occupants and cargo) is permitted to tow. It is determined by subtracting the weight of the loaded trailer towing vehicle from the GCWR for the towing vehicle. •...
Page 197 Driving Special loading instructions for owners of pickup trucks and utility-type vehicles For important information regarding safe operation of this type of vehicle, see the Preparing to drive your vehicle section in this chapter. Loaded vehicles, with a higher center of gravity, may handle differently than unloaded vehicles.
Page 198 Driving Driving through deep water where the transmission vent tube is submerged may allow water into the transmission and cause internal transmission damage. Have the fluid checked and, if water is found, replace the fluid. TRAILER TOWING Trailer towing with your vehicle may require the use of a trailer tow option package.
Page 199 Driving 4x2 w/automatic transmission GCWR (Gross Combined Weight Rating)/Trailer Weight Engine Rear axle ratio Maximum Trailer weight GCWR-kg range-kg (lbs.) (lbs.) (0-Maximum) 4.0L SOHC/4.6L 3.55 3493 (7700) 0-1451 (0-3200) 4.0L SOHC 3.73 LS 4645 (10240) 0-2595 (0-5720) 4.6L* 3.73 LS 5262 (11600) 0-3211 (0-7080) Notes: - For high altitude operation, reduce GCW by 2% per 300...
Page 200 Driving AWD w/automatic transmission GCWR (Gross Combined Weight Rating)/Trailer Weight Engine Rear axle ratio Maximum Trailer weight GCWR-kg range-kg (lbs.) (lbs.) (0-Maximum) *-When towing maximum loads under high outside temperatures and on steep grades, the A/C system may cycle on and off to protect the engine from overheating.
Page 201 Driving Trailer brakes Electric brakes and manual, automatic or surge-type trailer brakes are safe if installed properly and adjusted to the manufacturer’s specifications. The trailer brakes must meet local and Federal regulations. Do not connect a trailer’s hydraulic brake system directly to your vehicle’s brake system.
Page 202 Driving Trailer towing tips • Practice turning, stopping and backing up before starting on a trip to get the feel of the vehicle trailer combination. When turning, make wider turns so the trailer wheels will clear curbs and other obstacles. •...
Page 203 Driving Rear Wheel Drive (RWD) 4x2 vehicles: This applies to all 4x2 trucks/sport utilities with rear wheel drive capability. An example of recreational towing is towing your vehicle behind a motorhome. The following recreational towing guidelines are designed to ensure that your transmission is not damaged. •...
Page 204 Driving To adjust cross-bar position: 1. Loosen the thumbwheel at both ends of the cross-bar (both cross-bars are adjustable). 2. Slide the cross-bar to the desired location. 3. Tighten the thumbwheel at both ends of the cross-bar. Vehicles with a higher center of gravity such as utility and four-wheel drive vehicles handle differently than vehicles with a lower center of gravity.
Page 205: Roadside Emergencies
In the United States, this card is found in the Owner Guide portfolio in the glove compartment in Ford vehicles and is mailed to you if you own a Mercury or Lincoln. In Canada, the card is found in the Owner Information Guide in the glove compartment.
Page 206: Roadside Emergencies
If you need to arrange roadside assistance for yourself, Ford Motor Company will reimburse a reasonable amount. To obtain reimbursement information, U.S. Ford or Mercury vehicles customers call 1-800-241-3673; Lincoln vehicle customers call 1–800–521–4140. Canadian customers who need to obtain reimbursement information, call 1–800–665–2006.
Page 207 Roadside emergencies The fuel pump shut-off switch is located in the passenger’s foot well, by the kick panel. Use the following procedure to reset the fuel pump shut-off switch. 1. Turn the ignition to the OFF position. 2. Check the fuel system for leaks. 3.
Page 208 Roadside emergencies Standard fuse amperage rating and color COLOR Cartridge Fuse Mini Standard Maxi Fuse link maxi rating fuses fuses fuses cartridge fuses Grey Grey — — — Violet Violet — — — Pink Pink — — — — — —...
Page 209 Roadside emergencies The fuses are coded as follows: Fuse/Relay Fuse Amp Passenger Compartment Fuse Panel Location Rating Description Memory seat module Heated seats, Moonroof Radio, Amplifier, Power antenna, DVD Front wiper module Flasher relay (Turn, hazards) Right horn Heated mirrors –...
Page 210 Roadside emergencies Fuse/Relay Fuse Amp Passenger Compartment Fuse Panel Location Rating Description — Not used (spare) Foglamp switch, 4x4 module Overdrive cancel switch, Flex fuel sender PATS module Rear wiper module, Cluster, TPMS Power mirror, Manual climate control, TPMS Delayed acc. coil, Battery saver, Interior lamps (front and rear), Glove compartment lamp Left horn...
Page 211 Roadside emergencies Passenger compartment fuse panel (top side) These relays are located on the reverse side of the passenger compartment fuse panel. To access the relays you must remove the passenger compartment fuse panel. Fuse/Relay Location Description Relay 1 Flasher relay Relay 2 Rear defrost Relay 3...
Page 212 Roadside emergencies Power distribution box The power distribution box is located in the engine compartment. The power distribution box contains high-current fuses that protect your vehicle’s main electrical systems from overloads. Always disconnect the battery before servicing high current fuses. To reduce risk of electrical shock, always replace the cover to the Power Distribution Box before reconnecting the battery or refilling fluid reservoirs.
Page 213 Roadside emergencies The high-current fuses are coded as follows: Fuse/Relay Fuse Amp Power Distribution Box Description Location Rating 60A** 30A** 20A** GCC pusher fan (export only) 30A** Rear defrost 40A** Anti-lock Brake System (ABS) pump 60A** Delayed accessory circuit breaker 20A** Power point #2 —...
Page 214 Roadside emergencies Fuse/Relay Fuse Amp Power Distribution Box Description Location Rating 20A** High beam relay 30A** Electric brake 30A** Front wiper motor 20A** Autolamp; Low beam 30A** Ignition switch 20A* Rear fog lamps (Export only) – Not used 15A* Fuel pump 20A* Trailer tow lamps 20A*...
Page 215 Roadside emergencies Fuse/Relay Fuse Amp Power Distribution Box Description Location Rating — Fog lamp relay — Police IVD relay — A/C clutch relay — Trailer tow right turn — Trailer tow left turn — Blower motor relay — Starter relay —...
Page 216 Roadside emergencies The relays are coded as follows: Fuse/Relay Location Description Relay 14 Not used Relay 15 Trailer tow back- up lamps Relay 16 Not used Relay 17 Not used Relay 18 Not used Relay 19 Trailer tow park lamps Relay 20 Trailer tow battery charge Relay 21...
Page 217 Roadside emergencies The relays are coded as follows: Fuse/Relay Location Description Relay 64 Police vehicles equipped with AdvanceTrac Relay 65 Open Relay 66 Open CHANGING THE TIRES If you get a flat tire while driving, do not apply the brake heavily. Instead, gradually decrease your speed.
Page 218 Roadside emergencies Location of the spare tire and tools The spare tire and tools for your vehicle are stowed in the following locations: Tool Location Spare tire Under the vehicle, just in front of the rear bumper. The spare tire winch drive nut is located at the rear center of the cargo area under a lid.
Page 219 Roadside emergencies Removing the spare tire Do not use an impact wrench on the winch drive nut. This will damage the spare tire winch. 1. Open the cover from the carpeting on cargo floor to expose the winch drive nut. 2.
Page 220 Roadside emergencies Refer to the tire changing instruction sheet for detailed tire change instructions. 1. Park on a level surface, activate hazard flashers and set the parking brake. 2. Place gearshift lever in P (Park) and turn engine OFF. When one of the rear wheels is off the ground, the transmission alone will not prevent the vehicle from moving...
Page 221 Roadside emergencies 6. Assemble the jack handle extension on the lug nut wrench by sliding the square end of the jack handle through the plastic grommet on the lug nut wrench and into the square hole on the other side. 7.
Page 222 Roadside emergencies To lessen the risk of personal injury, do not put any part of your body under the vehicle while changing a tire. Do not start the engine when your vehicle is on the jack. The jack is only meant for changing the tire. •...
Page 223 Roadside emergencies 2. Slide the wheel under the vehicle and install the retainer through the wheel center. 3. Turn the lug wrench clockwise until the tire is raised to its original position underneath the vehicle. The lug wrench will click when the tire is raised to the stowed position.
Page 224 Roadside emergencies 4. Check all battery terminals and remove any excessive corrosion before you attach the battery cables. Ensure that vent caps are tight and level. 5. Turn the heater fan on in both vehicles to protect any electrical surges. Turn all other accessories off. Connecting the jumper cables 1.
Page 225 Roadside emergencies 3. Connect the negative (-) cable to the negative (-) terminal of the assisting battery. 4. Make the final connection of the negative (-) cable to the provided jumpstarting bolt ONLY. Connecting to any other exposed component may cause an explosion. Do not use fuel lines, engine rocker covers or the intake manifold as grounding points.
Page 226 Roadside emergencies 4.0L Engine 4.6L Engine...
Page 227 Roadside emergencies 5. Ensure that the cables are clear of fan blades, belts, moving parts of both engines, or any fuel delivery system parts. Jump starting 1. Start the engine of the booster vehicle and run the engine at moderately increased speed. 2.
Page 228 Roadside emergencies 3. Remove the jumper cable from the positive (+) terminal of the booster vehicle’s battery. 4. Remove the jumper cable from the positive (+) terminal of the disabled vehicle’s battery. After the disabled vehicle has been started and the jumper cables removed, allow it to idle for several minutes so the engine computer can relearn its idle conditions.
Page 229 Roadside emergencies WRECKER TOWING If you need to have your vehicle towed, contact a professional towing service or, if you are a member, your roadside assistance center. It is recommended that your vehicle be towed with a wheel lift or flatbed equipment.
Page 230: Maintenance And Care
Maintenance and care SERVICE RECOMMENDATIONS To help you service your vehicle: • We highlight do-it-yourself items in the engine compartment for easy location. • We provide a scheduled maintenance guide which makes tracking routine service easy. If your vehicle requires professional service, your dealership can provide the necessary parts and service.
Page 231 Maintenance and care OPENING THE HOOD 1. Inside the vehicle, pull the hood (rearward) release handle located under the bottom left corner of the instrument panel.
Page 232 Maintenance and care 2. Go to the front of the vehicle and release the auxiliary latch that is located under the front center of the hood. 3. Lift the hood.
Page 233 Maintenance and care IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 4.0L SOHC V6 engine 1. Engine coolant reservoir 2. Engine oil filler cap 3. Engine oil dipstick 4. Brake fluid reservoir 5. Power distribution box 6. Battery 7. Power steering fluid reservoir 8.
Page 234 Maintenance and care 4.6L V8 engine 1. Engine coolant reservoir 2. Engine oil dipstick 3. Brake fluid reservoir 4. Power distribution box 5. Battery 6. Power steering fluid reservoir 7. Engine oil filler cap 8. Air filter assembly 9. Windshield washer fluid reservoir ENGINE OIL Checking the engine oil Refer to the scheduled maintenance guide for the appropriate intervals...
Page 235 Maintenance and care 3. Set the parking brake and ensure the gearshift is securely latched in P (Park). 4. Open the hood. Protect yourself from engine heat. 5. Locate and carefully remove the engine oil level indicator (dipstick). • 4.0L V6 engine...
Page 236 Maintenance and care • 4.6L V8 engine 6. Wipe the indicator clean. Insert the indicator fully, then remove it again. • If the oil level is between the MIN and MAX marks, the oil level is acceptable, DO NOT ADD OIL. •...
Page 237 Maintenance and care • 4.0L SOHC V6 engine • 4.6L V8 engine • Oil levels above the MAX mark may cause engine damage. Some oil must be removed from the engine by a service technician. 7. Put the indicator back in and ensure it is fully seated. Adding engine oil 1.
Page 238 Maintenance and care 3. Recheck the engine oil level. Make sure the oil level is not above the MAX hole on the engine oil level indicator (dipstick). 4. Install the indicator and ensure it is fully seated. 5. Fully install the engine oil filler cap by turning the filler cap clockwise 1/4 of a turn or until three clicks can be heard.
Page 239 Maintenance and care 4.0L Engine Look for this certification trademark. SAE 5W-30 engine oil is recommended. Only use oils “Certified For Gasoline Engines” by the American Petroleum Institute (API). Use Motorcraft or an equivalent oil meeting Ford Specification WSS-M2C205–H. Do not use supplemental engine oil additives, oil treatments or engine treatments.
Page 240 Maintenance and care BRAKE FLUID Checking and adding brake fluid Brake fluid should be checked and refilled as needed. Refer to the scheduled maintenance guide for the service interval schedules. 1. Clean the reservoir cap before removal to prevent dirt or water from entering the reservoir.
Page 241 Maintenance and care WINDSHIELD WASHER FLUID Windshield washer fluid Check the washer fluid whenever you stop for fuel. The reservoir is highlighted with a symbol. Add fluid to fill the reservoir if the level is low. In very cold weather, do not fill the reservoir completely.
Page 242 Maintenance and care Your vehicle was factory-filled with a 50/50 engine coolant and water concentration. If the concentration of coolant falls below 40% or above 60%, the engine parts could become damaged or not work properly. A 50–50 mixture of coolant and water provides the following: •...
Page 243 Maintenance and care Do not put engine coolant in the windshield washer fluid container. If sprayed on the windshield, engine coolant could make it difficult to see through the windshield. The cooling system in your vehicle is filled with either green-colored Motorcraft Premium Engine Coolant meeting Ford specification ESE-M97B44–A or yellow-colored Motorcraft Premium Gold Engine Coolant meeting Ford Specification WSS-M97B51–A1.
Page 244 Maintenance and care For vehicles with overflow coolant systems with a non-pressurized cap on the coolant recovery system, add coolant to the coolant recovery reservoir when the engine is cool. Add the proper mixture of coolant and water to the “cold full” level. For all other vehicles, which have a coolant degas system with a pressurized cap, or if it is necessary to remove the coolant pressure relief cap on the radiator of a vehicle with an overflow system, follow these steps to add engine coolant.
Page 245 Maintenance and care Recycled engine coolant Ford Motor Company recommends the use of a recycled engine coolant produced by Ford-approved processes in vehicles originally equipped with Motorcraft Premium Engine Coolant (green-colored). However, not all coolant recycling processes produce coolant that meets Ford specification ESE-M97B44–A.
Page 246 Maintenance and care How fail-safe cooling works If the engine begins to overheat: • The engine coolant temperature gauge will move to the red (hot) area. • The and the symbol will illuminate. • The “Service Engine Soon” indicator light will illuminate. If the engine reaches a preset over-temperature condition, the engine will automatically switch to alternating cylinder operation.
Page 247 Maintenance and care 5. Restart the engine and take your vehicle to a service facility. Driving the vehicle without repairing the engine problem increases the chance of engine damage. Take your vehicle to a service facility as soon as possible. CHECKING AND ADDING POWER STEERING FLUID Check the power steering fluid.
Page 248 Maintenance and care 6. If the fluid is low, add fluid in small amounts, continuously checking the level until it reaches the correct operating range. Be sure to put the cap back on the reservoir. TRANSMISSION FLUID Checking automatic transmission fluid The automatic transmission does not have a transmission fluid dipstick.
Page 249 Maintenance and care 3. Add only enough fluid through the filler opening so that the fluid level is at the bottom of the opening. Use only fluid that meets Ford specifications. Refer to Lubricant Specifications in the Capacities and specifications chapter. DRIVELINE UNIVERSAL JOINT AND SLIP YOKE Your vehicle may be equipped with universal joints that require lubrication.
Page 250 Maintenance and care If your battery has a cover/shield, make sure it is reinstalled after the battery has been cleaned or replaced. For longer, trouble-free operation, keep the top of the battery clean and dry. Also, make certain the battery cables are always tightly fastened to the battery terminals.
Page 251 Maintenance and care 3. Run the engine until it reaches normal operating temperature. 4. Allow the engine to idle for at least one minute. 5. Turn the A/C on and allow the engine to idle for at least one minute. 6.
Page 252 Maintenance and care Changing the wiper blades To replace the wiper blades: 1. Pull the wiper arm away from the windshield and lock into the service position. 2. Turn the blade at an angle from the wiper arm. Push the lock pin manually to release the blade and pull the wiper blade down toward the windshield to remove it from the...
Page 253 Maintenance and care Treadwear The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire graded 150 would wear one and one-half (1 1/2) times as well on the government course as a tire graded 100.
Page 254 Maintenance and care SERVICING YOUR TIRES Checking the tire pressure • Use an accurate tire pressure gauge. • Check the tire pressure when tires are cold, after the vehicle has been parked for at least 3 hours or has been driven less than 5 km (3 miles).
Page 255 Maintenance and care • Five tire rotation Replacing the tires Replace the tires when the wear band is visible through the tire treads. When replacing full size tires, never mix radial bias-belted, or bias-type tires. Use only the tire sizes that are listed on the Certification Label.
Page 256 Maintenance and care Do not replace your tires with “high performance” tires or larger size tires. Failure to follow these precautions may adversely affect the handling of the vehicle and make it easier for the driver to lose control and roll over. Tires that are larger or smaller than your vehicle’s original tires may also affect the accuracy of your speedometer.
Page 257 Maintenance and care Changing tires with TPMS It is recommended that you always have your tires serviced by a dealer or qualified technician. Each tire is equipped with a tire pressure sensor mounted on the wheel inside the tire behind the valve stem.
Page 258 Maintenance and care Consult your dealer for information on other Ford approved methods of traction control. WHAT YOU SHOULD KNOW ABOUT AUTOMOTIVE FUELS Important safety precautions Do not overfill the fuel tank. The pressure in an overfilled tank may cause leakage and lead to fuel spray and fire. The fuel system may be under pressure.
Page 259 Maintenance and care • Avoid inhaling fuel vapors. Inhaling too much fuel vapor of any kind can lead to eye and respiratory tract irritation. In severe cases, excessive or prolonged breathing of fuel vapor can cause serious illness and permanent injury. •...
Page 260 Maintenance and care become brittle and crack, especially when mixed with gasoline. Special materials and procedures have been developed for flexible fuel vehicles and the dispensers used by ethanol fuel providers. Flexible fuel components and standard unleaded gasoline fuel components are not interchangeable. If your vehicle is not serviced in accordance with flexible fuel vehicles procedures, damage may occur and your warranty may be invalidated.
Page 261 Maintenance and care Repairs to correct the effects of using a fuel for which your vehicle was not designed may not be covered by your warranty. Octane recommendations Do not be concerned if your engine sometimes knocks lightly. However, if it knocks heavily under most driving conditions while you are (R+M)/2 METHOD using fuel with the recommended...
Page 262 Maintenance and care rating. Aftermarket products could cause damage to the fuel system. Repairs to correct the effects of using an aftermarket product in your fuel may not be covered by your warranty. Unleaded Gasoline engines If you are experiencing starting, rough idle or hesitation driveability problems during a cold start, try a different brand of “Regular”...
Page 263 Maintenance and care When fueling your vehicle: 1. Turn the engine off. 2. Carefully turn the filler cap counterclockwise 1/8 of a turn until it stops. 3. Pull to remove the cap from the fuel filler pipe. 4. To install the cap, align the tabs on the cap with the notches on the filler pipe.
Page 264 Maintenance and care possible. Fuel expense, frequency of fill-ups or fuel gauge readings are NOT accurate as a measure of fuel economy. We do not recommend taking fuel economy measurements during the first 1,600 km (1,000 miles) of driving (engine break-in period). You will get a more accurate measurement after 3,000 km–5,000 km (2,000 miles-3,000 miles).
Page 265 Maintenance and care Calculating fuel economy 1. Fill the fuel tank completely and record the initial odometer reading (in kilometers or miles). 2. Each time you fill the tank, record the amount of fuel added (in liters or gallons). 3. After at least three to five tank fill-ups, fill the fuel tank and record the current odometer reading.
Page 266 Maintenance and care • You may want to turn off the speed control in hilly terrain if unnecessary shifting between third and fourth gear occurs. Unnecessary shifting of this type could result in reduced fuel economy. • Warming up a vehicle on cold mornings is not required and may reduce fuel economy.
Page 267 Maintenance and care Per Gallon (MPG) and your driving range to decrease by about 30% compared to gasoline operation. EPA window sticker Every new vehicle should have the EPA window sticker. Contact your dealer if the window sticker is not supplied with your vehicle. The EPA window sticker should be your guide for the fuel economy comparisons with other vehicles.
Page 268 Maintenance and care Exhaust leaks may result in entry of harmful and potentially lethal fumes into the passenger compartment. Do not make any unauthorized changes to your vehicle or engine. By law, vehicle owners and anyone who manufactures, repairs, services, sells, leases, trades vehicles, or supervises a fleet of vehicles are not permitted to intentionally remove an emission control device or prevent it from working.
Page 269 Maintenance and care BULBS Replacing exterior bulbs Check the operation of the following lamps frequently: • Headlamps • Turn signal lamps • Side marker lamps • Foglamps • License plate lamp • High-mount brakelamp • Tail lamps • Brakelamps • Back-up lamps Do not remove lamp bulbs unless they can be replaced immediately with new ones.
Page 270 Maintenance and care 3. Remove the protective dust cap from the housing by turning counterclockwise (when viewed from the rear). 4. Disconnect the electrical connector from the bulb by pulling rearward. 5. Remove the bulb retaining ring by rotating it counterclockwise. 6.
Page 271 Maintenance and care Replacing front parking lamp/turn signal bulbs 1. Make sure headlamp switch is in OFF position, then open the hood. 2. At the back of the headlamp, pry up and remove the two retainer pins to release the headlamp assembly from the vehicle and pull headlamp forward.
Page 272 Maintenance and care Replacing side repeater bulbs 1. Carefully pry the lamp assembly away from the fender. 2. Rotate the bulb socket counterclockwise and remove from lamp assembly. 3. Carefully pull bulb straight out of socket and push in the new bulb. 4.
Page 273 Maintenance and care 5. Pull the bulb straight out of the socket and push in the new bulb. 6. To complete installation, follow the removal procedure in reverse order. Replacing foglamp bulbs 1. Reach under the front of the front bumper and remove the bulb socket from the foglamp by turning counterclockwise.
Page 274 Maintenance and care Replacing high-mount brake lamp bulbs 1. Remove the two screws and move the lamp assembly away from the liftgate. 2. Remove the bulb holder from the lamp assembly by depressing the snaps. 3. Pull the bulb straight out of the socket and push in the new bulb.
Page 275 Maintenance and care Function Number of bulbs Trade number Park/turn lamps (front) 3157 AK (amber) Headlamps 9007 Rear stop/turn/tail lamps 3057 Rear license plate lamps Backup lamp 3156K High-mount brake lamps Side repeater WY5W (amber) Front sidemarker Rear sidemarker Fog lamp 9145 Cargo lamp 211-2...
Page 276 Maintenance and care • (4) Horizontal reference line 2. Measure the height from the center of your headlamp to the ground and mark a 2.4 meter (8 foot) horizontal reference line on the vertical wall or screen at this height (a piece of masking tape works well).
Page 277 Maintenance and care • Never use strong household detergents or soap, such as dish washing or laundry liquid. These products can discolor and spot painted surfaces. • Never wash a vehicle that is “hot to the touch” or during exposure to strong, direct sunlight.
Page 278 Maintenance and care Aluminum wheels and covers Aluminum wheel rims or covers are coated with a clearcoat paint finish. In order to maintain their shine: • Clean with Motorcraft Wheel and Tire Cleaner (ZC-37–A), which is available from your dealer. •...
Page 279 Maintenance and care • Cover the highlighted areas to prevent water damage when cleaning the engine. 4.6L V8 Engine 4.0L SOHC V6 Engine • Never wash or rinse the engine while it is running; water in the running engine may cause internal damage. Plastic (non-painted) exterior parts Use only approved products to clean plastic parts.
Page 280 Maintenance and care • If tar or grease spots are present, use Ford Extra Strength Tar and Road Oil Removal (B7A-19520–AA). Windows and wiper blades The windshield, rear window and wiper blades should be cleaned regularly. If the wiper does not wipe properly, substances on the windshield, rear window or the wiper blades may be the cause.
Page 281 Maintenance and care • Remove light stains and soil with Ford Extra Strength Upholstery Cleaner (E8AZ-19523–AA). • If grease or tar is present on the material, spot-clean the area first with Motorcraft Spot and Stain Remover (ZC-14). • Never saturate the seat covers with cleaning solution. •...
Page 282 Maintenance and care Ford, Lincoln and Mercury car care products Your Ford, Lincoln or Mercury dealer has many quality products available to clean your vehicle and protect its finishes. These quality products have been specifically engineered to fulfill your automotive needs; they are custom designed to complement the style and appearance of your vehicle.
Page 283: Capacities And Specifications
Capacities and specifications MOTORCRAFT PART NUMBERS Component 4.0L SOHC V6 engine 4.6L V8 engine Air filter element FA-1695 FA-1695 Fuel filter FG-986B FG-986B Battery BXT-65-650 BXT-65-650 Oil filter FL-820S FL-820S PCV valve EV-243 F6ZE-6C324-CA Spark plugs* AGSF-22PP ** AWSF-32P * Refer to Vehicle Emissions Control Information (VECI) decal for spark plug gap information.
Page 284: Capacities And Specifications
Capacities and specifications Fluid Ford Part Application Capacity Name Power steering Motorcraft Fill between fluid MERCON MIN and MAX lines on reservoir Transmission Motorcraft 12.0L (12.7 fluid MERCON V quarts) Transfer case Motorcraft 1.25L (1.3 MERCON quarts) Engine coolant Motorcraft 4.0L SOHC V6 15.4L (16.3 Premium Engine...
Page 285 Capacities and specifications Fluid Ford Part Application Capacity Name Rear axle Motorcraft SAE Refer to 2.9-3.1L (5.5-5.8 lubricant 80W-90 Footnote 4 pints) Premium Rear Axle Lubricant Motorcraft SAE Refer to 75W-140 High Footnote 5 Performance Synthetic Rear Axle Lubricant Windshield Motorcraft All vehicles 4.0L (4.2...
Page 286 Capacities and specifications LUBRICANT SPECIFICATIONS Ford Part Ford Part Ford Item Name or Number Specification equivalent Body hinges, latches, door striker plates and rotors, seat Multi-Purpose ESR-M1C159-A tracks, fuel filler Grease or XG—4 or XL-5 door hinge and Multi-Purpose ESB-M1C93–B spring, hood Grease Spray latch, auxiliary...
Page 287 Capacities and specifications Ford Part Ford Part Ford Item Name or Number Specification equivalent Motorcraft SAE WSS-M2C153-H 5W20 Premium with API 4.6L Engine oil XO -5W20-QSP Synthetic Blend Certification Motor Oil Mark Motorcraft Automatic MERCON V XT-5-QM MERCON V transmission Motorcraft Power steering MERCON...
Page 288 Capacities and specifications Ensure the correct automatic transmission fluid is used. MERCON and MERCON V are not interchangeable. DO NOT mix MERCON and MERCON V. Refer to your scheduled maintenance guide to determine the correct service interval. Limited-slip differentials must add 118 ml (4 oz) of Additive Friction Modifier XL—3 or equivalent meeting Ford specification EST-M2C118–A to the rear axle whenever the axle has been serviced.
Page 289 Capacities and specifications...
Page 290 Capacities and specifications IDENTIFYING YOUR VEHICLE Certification label The National Highway Traffic Safety Administration Regulations require that a Certification label be affixed to a vehicle and prescribe where the Certification label may be located. The Certification label is located on the front door latch pillar on the driver’s side.
Page 291 Capacities and specifications 1. World manufacturer identifier 2. Brake type and gross vehicle weight rating (GVWR) 3. Vehicle line, series, body type 4. Engine type 5. Check digit 6. Model year 7. Assembly plant 8. Production sequence number Engine number The engine number (the last eight numbers of the vehicle identification number) is stamped on the engine block, transmission, frame and transfer case (if equipped).
Page 292: Customer Assistance
Warranty expires. You may purchase Ford ESP from any participating Ford and Lincoln Mercury and Ford of Canada dealer. There are several plans available in various time, distance and deductible combinations which can be tailored to fit your own driving needs. Ford ESP also offers reimbursement benefits for towing and rental coverage.
Page 293: Customer Assistance
Ford Customer Relationship Center. Away from home If you own a Ford or Mercury vehicle and are away from home when your vehicle needs service, or if you need more help than the dealership could provide, after following the steps described above, contact the Ford Customer Relationship Center to find an authorized dealership to help you.
Page 294 P.O. Box 2000 Oakville, Ontario L6J 5E4 1-800-565-3673 (FORD) www.ford.ca In order to help you service your Ford or Lincoln Mercury vehicle, please have the following information available when contacting a Customer Relationship Center: • Your telephone number (home and business) •...
Page 295 What kinds of cases does the Board review? Unresolved warranty repair concerns or vehicle performance concerns as on Ford and Lincoln Mercury cars and Ford and Lincoln Mercury light trucks which are within the terms of any applicable written new vehicle warranty are eligible for review, except those involving: •...
Page 296 • A Ford or Lincoln Mercury dealership representative Consumer candidates for Board membership are recruited and trained by an independent consulting firm. The dealership Board member is chosen from Ford and Lincoln Mercury dealership management, recognized for their business leadership qualities. What the Board needs...
Page 297 Customer assistance Oral presentations If you would like to make an oral presentation, indicate YES to question 6 on the application. While it is your right to make an oral presentation before the Board, this is not a requirement and the Board will decide the case whether or not an oral presentation is made.
Page 298 Customer assistance UTILIZING THE MEDIATION/ARBITRATION PROGRAM (CANADA ONLY) In those cases where you continue to feel that the efforts by Ford and the dealer to resolve a factory-related vehicle service concern have been unsatisfactory, Ford of Canada participates in an impartial third party mediation/arbitration program administered by the Canadian Motor Vehicle Arbitration Plan (CAMVAP).
Page 299 Ford accessories for your vehicle A wide selection of genuine Ford accessories are available for your vehicle through your local authorized Ford, Lincoln Mercury or Ford of Canada dealer. These quality accessories have been specifically engineered to fulfill your automotive needs; they are custom designed to complement the style and aerodynamic appearance of your vehicle.
Page 300 Customer assistance Vehicle Security Styled wheel locks Vehicle security systems Comfort and convenience Cargo net Cargo organizer Cargo shade Cargo tray Engine block heaters Home link visor Tire step Travel equipment Ash cup Cargo organizer Cargo tray Cellular phone holder Daytime running lamps Dog guard Engine block heater...
Page 301 Customer assistance Running boards Scuff plates Seatback storage Smoker’s package Soft luggage cover Tire step Trailer hitch (Class III) Trailer hitch bars and balls Trailer hitch mounted bike carrier Trailer hitch receiver cover Trailer hitch wiring adaptor Vehicle security systems Wheel locks Protection and appearance equipment Air bag anti-theft locks...
Page 302 Customer assistance For maximum vehicle performance, keep the following information in mind when adding accessories or equipment to your vehicle: • When adding accessories, equipment, passengers and luggage to your vehicle, do not exceed the total weight capacity of the vehicle or of the front or rear axle (GVWR or GAWR as indicated on the Safety compliance certification label).
Page 303 Customer assistance Obtaining a French owner’s guide French Owner’s Guides can be obtained from your dealer or by writing to Ford Motor Company of Canada, Limited, Service Publications, P.O. Box 1580, Station B, Mississauga, Ontario L4Y 4G3. IN CALIFORNIA (U.S. ONLY) California Civil Code Section 1793.2(d) requires that, if a manufacturer or its representative is unable to repair a motor vehicle to conform to the vehicle’s applicable express warranty after a reasonable number of...
Page 304: Reporting Safety Defects
Reporting safety defects REPORTING SAFETY DEFECTS (U.S. ONLY) If you believe that your vehicle has a defect which could cause a crash or could cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying Ford Motor Company. If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign.
Page 305 Index fluid, specification ....287 Auxiliary power point ....98 ABS (see Brakes) .....174 Axle Accessory delay ......94 lubricant specifications ..285, 287 refill capacities ......282 Air bag supplemental restraint system ......149–150, 154 and child safety seats ....152 description ......150, 154 Battery ........248 disposal ........157 acid, treating emergencies ..248 driver air bag ....152, 155...
Page 306: Index
Index Changing a tire ......216 Ford Extended Service Plan ..........291 Child safety restraints ....158 Getting assistance outside child safety belts ....158 the U.S. and Canada ....297 Child safety seats ......161 Getting roadside assistance ...204 attaching with tether straps ..166 Getting the service you in front seat ......163 need .........291 in rear seat ......163, 165...
Page 307 Index Emergencies, roadside calculating fuel jump-starting ......222 economy ......22, 262 cap ........10, 261 Emission control system ..266 capacity ........282 Engine ........287 choosing the right fuel ...259 check engine/service engine comparisons with EPA fuel soon light ........9 economy estimates ....266 cleaning ........277 detergent in fuel .....261 coolant ........240 filling your vehicle with...
Page 308 Index GAWR (Gross Axle Weight Infant seats (see Safety seats) .....161 Rating) ........194 calculating .......196 Inspection/maintenance (I/M) testing ........267 definition .........194 driving with a heavy load ..194 Instrument panel location ........194 cleaning ........279 cluster ..........8 GVWR (Gross Vehicle Weight lighting up panel and Rating) ........194 interior ........32 calculating .......194, 196...
Page 309 Index interior lamps ......87 replacing bulbs ..268, 270–273 Manual transmission Lane change indicator lubricant specifications ..287 (see Turn signal) ......77 Message center .....19–20 Liftgate ........99, 103 english/metric button ....25 Lights, warning and indicator ..8 system check button ....25 AdvanceTrac ......12 warning messages .....25 air bag ........10 Mirrors .........93...
Page 310 Index fluid, checking and adding ..246 for children ......158 fluid, refill capacity ....282 lap belt ........139 fluid, specifications ..285, 287 warning light and chime ......10, 13, 143 Power Windows ......93 Safety seats for children ..161 Preparing to drive your vehicle ........180 Seat belts (see Safety restraints) ........133 Seats ..........120...
Page 311 Index replacing ......218, 254 Vehicle Identification Number rotating ........253 (VIN) ..........289 snow tires and chains ....256 Vehicle loading ......194 spare tire ......216–218 tire grades .......252 Ventilating your vehicle ...173 treadwear ........252 Towing ........197 recreational towing ....201 trailer towing ......197 Warning chimes ......13 wrecker ........228 Warning lights (see Lights) ..8 Traction control ......177...
Page 312: Filling Station Information
Filling station information Item Information Required fuel Unleaded fuel only - 87 octane Fuel tank capacity 85.2L (22.5 gallons) 4.0L Engine oil capacity (includes 4.7L (5.0 quarts). Use Motorcraft filter change) SAE 5W-30 Super Premium Motor Oil, Ford specification WSS-M2C153-G. 4.6L Engine oil capacity (includes 5.7L (6.0 quarts).
Page 313 Filling station information Ensure the correct automatic transmission fluid is used. MERCON and MERCON V are not interchangeable. DO NOT mix MERCON and MERCON V. Refer to your scheduled maintenance guide to determine the correct service interval. Indicates only approximate dry-fill capacity. Some applications may vary based on cooler size and if equipped with in-tank cooler.

Mercury Mountaineer 2002 Owner's Manual

Quick Links

Related Manuals for Mercury Mountaineer 2002

Summary of Contents for Mercury Mountaineer 2002

Table of Contents