Mercury Mountaineer 1997 Owner's Manual

Mercury Mountaineer 1997 Owner's Manual

Lincoln 1997 mountaineer owner's guide

Advertisement

Advertisement

Table of Contents
loading

Summary of Contents for Mercury Mountaineer 1997

  • Page 1: Table Of Contents

    BEFORE DRIVING Introduction Instrumentation Controls and features Seating and safety restraints STARTING AND DRIVING Starting your vehicle Driving Roadside emergencies SERVICING Maintenance and care Capacities and specifications Reporting safety defects Index Filling station information Table of contents...
  • Page 2: Introduction

    Introduction The following icons appear in this Owner’s Guide: indicates a warning. Read the following section on Warnings for a full explanation of warnings. indicates that vehicle information related to recycling and other environmental concerns will follow. Warnings Warnings remind you to be especially careful in those areas where carelessness can cause damage to your vehicle or personal...
  • Page 3 differences for towing, hauling, and off-road operation. For this reason, Mercury urges you to read and understand the contents of the Four-Wheeling supplement. Breaking in your vehicle Your new vehicle goes through an adjustment or breaking-in period during the first 1,000 miles (1,600 km) of driving.
  • Page 4 Instrumentation Engine coolant Warning lights temperature (pg. 8) gauge (pg. 7 ) Tachometer (pg. 6) Fuel gauge (pg. 7) Hazard flasher control (not shown) (pg. 27) Headlamp control (pg. 13) Instrument panel dimmer switch (pg. 14) Tilt steering wheel lever (pg.
  • Page 5 Electronic sound system; refer to Audio Guide (premium stereo Vents cassette with CD DJ (pg. 17) shown) (pg. 16) VOL – PUSH ON FM 1 FM BASS TREB SEEK SCAN TUNE DOLBY SYSTEM DISCS SIDE 1-2 Climate controls (pg. 17) Instrumentation Rear Rear window...
  • Page 6 Instrumentation INSTRUMENT CLUSTER Instrument cluster gauges UNLEADED FUEL ONLY RPM x 1000 Speedometer Tachometer 50 60 70 o o o 0 0 0 0 0 0 km/h R N D 2 1 50 60 70 o o o 0 0 0 0 0 0 km/h UNLEADED FUEL ONLY...
  • Page 7 Engine coolant Fuel gauge Voltage gauge Oil pressure Odometer Trip odometer and reset button Instrumentation 50 60 70 o o o 0 0 0 0 0 0 km/h 50 60 70 o o o 0 0 0 0 0 0 km/h...
  • Page 8: Door Ajar

    Instrumentation Instrument cluster warning and indicator lights CHECK GAGE DOOR AJAR BRAKE DOOR illuminates when the ignition AJAR key is turned to the ON or START position and a door or liftgate is opened. illuminates when the ignition is CHECK GAGE turned to ON and the engine temperature is high, the oil...
  • Page 9: Instrumentation

    illuminates when the parking brake is activated, brake fluid level is low, or break system requires service. illuminates when the headlamp high beams are on. illuminates when the anti-lock brake system requires service. illuminates when the ignition key is turned to ON and the safety belt is not buckled.
  • Page 10 Instrumentation the transmission control indicator light (TCIL) illuminates when the transmission control switch on the end of the gearshift lever is pushed and the (Overdrive) mode is turned off. indicates the status of the transmission and may flash steadily if a malfunction is detected. If flashing persists, have your transmission serviced by your dealer as soon as possible.
  • Page 11 How to test the instrument cluster lights CHECK GAGE UNLEADED FUEL ONLY RPM x 1000 BRAKE Turn the ignition key to ON without starting the engine. The warning and indicator lights shown above will illuminate for a brief time. If any of these lights do not illuminate, have your vehicle serviced.
  • Page 12 Instrumentation Headlamps on warning chime A warning chime sounds when the headlamps are on (and key is not in the ignition), the ignition is off, and a door is opened.
  • Page 13: Controls And Features

    INSTRUMENT PANEL CONTROLS 50 60 70 o o o UNLEADED FUEL ONLY 0 0 0 0 0 0 km/h RPM x 1000 R N D 2 1 VOL – PUSH ON COAST Headlamp switch This switch operates the parking lamps and headlamps. OFF Exterior lamps off Parking lamps ON Headlamps ON...
  • Page 14 Controls and features Daytime running light (DRL) system (if equipped) The daytime running light (DRL) system turns the high beam lamps on, with a reduced light output, when: The headlamp knob is in the OFF position. The engine is running. The parking brake is released.
  • Page 15 Liftgate wiper and washer Turn the knob to adjust wiper speed. Push the knob in to activate the washer. Rear window defroster Push the button to activate the defroster. The indicator light will turn on and the defroster will turn off automatically in ten minutes.
  • Page 16 Controls and features Foglamps Push the button to activate the foglamps. The indicator light will turn on. The foglamps can be turned on only when the low beam headlamps are on. Push the button again to turn off. Audio system Refer to the Audio Guide for instructions on how to operate the audio system.
  • Page 17 Climate controls Instrument panel vents There are four vents on the instrument panel. These vents are equipped with dials to adjust the amount and direction of air passing through them. Controls and features 80 100 120 o o o UNLEADED FUEL ONLY 0 0 0 0 0 0 km/h...
  • Page 18 Controls and features Operating climate controls Turn the temperature control to the desired temperature. Turn the fan speed control to the desired speed. Turn the mode control to the desired airflow position.
  • Page 19 Controlling airflow Select for air to flow through these vents: position allows outside air to flow through the instrument panel vents. Select for air to flow through these vents: position directs outside air to flow between the panel and floor vents. The air conditioning will function provided the outside temperature is above 10°C (50°F).
  • Page 20 Controls and features Select A/C for air to flow through these vents: The A/C mode directs outside air conditioned air to flow through the instrument panel vents. The A/C mode can be used for heating, ventilating or air conditioning. The A/C mode only functions if the outside temperature is above 10°C (50°F).
  • Page 21 Maximum heating Set mode control to , turn temperature control to maximum heat (red) and set fan speed control to maximum. Maximum cooling Set mode control to MAX A/C, turn temperature control to maximum cool (blue) and set fan speed control to maximum.
  • Page 22 Controls and features STEERING COLUMN CONTROLS Positions of the ignition ACCESSORY allows electrical accessories such as radio and wipers/washer to operate while the engine is not running. LOCK locks the steering wheel and gearshift lever. OFF shuts off the ignition and accessories and allows the gearshift lever and steering wheel to move.
  • Page 23 Speed control Do not shift the transmission into N with the speed control on. Speed control maintains vehicle speed automatically at or above 48km/h (30 mph) using the control switches. Press ON to turn speed control on. SPEED will illuminate in the CONT instrument cluster.
  • Page 24 Controls and features Press SET ACCEL (with speed control turned ON) to set speed. Hold SET ACCEL to increase speed. Press and release once to increase speed in 1.6 km/h (1 mph) increments. Press COAST to decrease speed. Press RSM to resume speed. Depressing the brake pedal will cancel the speed control.
  • Page 25 Activating high beams Push the lever forward to activate the high beam lamps. Pull the lever towards you to activate the “flash to pass” function. Push the lever down to activate the left turn signal. Push the lever up to activate the right turn signal.
  • Page 26 Controls and features Overdrive control Activating overdrive Overdrive is the normal drive position for the best fuel economy and will remain on until overdrive is deactivated. The overdrive function allows automatic upshifts to 2nd, 3rd, and 4th gear. Deactivating overdrive Press the transmission control switch on the end of the gearshift lever.
  • Page 27 Hazard flasher Push the hazard flasher button. The button will pop out and the lamps will begin to flash. To stop the flashers, push the flasher button again. Tilt steering Never adjust the steering column while the vehicle is moving. Pull the tilt steering lever towards you and move the wheel to the desired position.
  • Page 28 Controls and features OVERHEAD CONTROLS Overhead console (if equipped) The console includes: compass/temperature display map lamps storage compartment garage door opener actuator moon roof control (if equipped) OPEN GARAGE LAMP MODE LAMP...
  • Page 29 Compass/temperature display Press the MODE button (with the ignition key in the ON position) to switch between the following features: display off temperature in C (Celsius) and compass temperature in F (Farenheit) and compass If the outside temperature is below 4°C (39°F), the word ICE will flash alternately with the temperature for one minute.
  • Page 30 Controls and features Compass zone adjustment 1. Determine which zone of the country you live in by referring to the zone map. 2. Press and hold the MODE button until VAR appears in the display; then release. The display will show the current zone number. 3.
  • Page 31 1. Press and hold the MODE button until CAL appears in the display (approximately eight seconds); then release. 2. Drive the vehicle slowly (less than 5 km/h/3 mph) in circles until the CAL indicator turns off (2-3 complete circles). Map lamps Press either the driver or passenger button to turn map lamps on or off.
  • Page 32 Controls and features 1. Remove storage clip from door. 2. Place Velcro™ hook onto side of aftermarket transmitter opposite of actuator button. 3. Place transmitter into storage compartment, button down. 4. Place the provided height adapters onto the back side of the GARAGE button as needed.
  • Page 33 Moon roof (if equipped) Press and hold bottom portion of moon roof switch to open. Press and hold top portion of moon roof switch to close. To raise the rear of the moon roof, close the moon roof and press top of rocker switch again.
  • Page 34 Controls and features 3. Slide the delay slide knob to the center of travel. The further you move the knob to the right, the longer the headlamps stay on after RELAY AUTOLAMP the ignition is turned to the OFF position. The autolamp will keep the headlamps on for a maximum of three minutes after the ignition is turned off.
  • Page 35 Controls and features DOOR MOUNTED CONTROLS Power windows Driver side control Press and hold rocker switch to close driver window. DOOR LOCK Press and release rocker switch for partial window movement. The driver side power window has a one touch down feature. When the AUTO switch is fully pressed, the driver side window will move completely down.
  • Page 36 Controls and features Press rocker switch to open the rear passenger window(s). Press rocker switch to close the rear passenger window(s). Your vehicle has a power window lock feature. When the power window lock feature is enabled, the passenger and the rear seat power windows cannot be operated by passengers.
  • Page 37 Passenger side control Press rocker switch to open window. Press rocker switch to close window. Rear seat passengers Press rocker switch to open right rear window. Press rocker switch to close right rear window. Press rocker switch to open left rear window.
  • Page 38 Controls and features Power locks Driver side Press U once to unlock all doors and liftgate. Press L once to lock all doors and liftgate. Passenger side Press U once to unlock all doors and liftgate. Press L once to lock all doors and liftgate.
  • Page 39 Controls and features Rear liftgate Press rocker switch (key graphic) once to unlock all doors and liftgate. Press opposite side to lock all doors and liftgate. DOOR LOCK Childproof locks for rear doors When you set these locks, the rear doors cannot be opened from the inside.
  • Page 40 Controls and features Move lever to LOCK position (up) to set the lock. Move lever to UNLOCK position (down) to disengage the lock. Two-step unlock feature (if equipped) This feature allows you to unlock all vehicle doors with the key. 1.
  • Page 41 liftgate will unlock when the key is returned to the vertical position (position of key before removal). This feature can be activated by all outside locks on vehicles equipped with keyless entry. Illuminated entry Interior lamps illuminate when either outside front door handle is lifted, unlocked with the keyless entry keypad or the UNLOCK button is pressed on the remote...
  • Page 42 Controls and features Power mirrors 1. Select driver or passenger mirror by moving selector lever left for driver or right for passenger. 2. Move the mirror control knob until mirror reaches desired position. 3. Return the selector lever to the center ‘‘off’’...
  • Page 43 Auxiliary power point This power point is an additional power source for electrical accessories. Do not plug optional electrical accessories into the cigarette lighter. Use the power point. Replacing the tissue box 1. Lift armrest and slide coinholder/tissue box out of console in an upward motion.
  • Page 44 Controls and features Rear console (if equipped) Your vehicle is equipped with a rear console that includes the following features: 1. Air vents 2. Audio system controls (refer to Audio Guide) 3. Rear seat climate control direction and fan controls 4.
  • Page 45 Controls and features Rear climate controls – VOLUME BAND SEEK MEMORY Turn the air distribution dial to the desired airflow position. – VOLUME BAND SEEK MEMORY Turn the fan speed dial to the desired position. – VOLUME BAND SEEK MEMORY...
  • Page 46 Controls and features Controlling airflow Select for air to flow through these vents: – VOLUME BAND SEEK MEMORY Select for air to flow through these vents: – VOLUME BAND SEEK MEMORY Cargo area controls Cargo cover (if equipped) Your vehicle is equipped with a cargo shade that covers the luggage compartment of your vehicle.
  • Page 47 Installing shade 1. Position shade in mounting brackets as shown (tongue faces rear of vehicle). 2. Pull end of shade towards you and hook sides into notches in rear trim panels. To avoid possible injury during a sudden stop or collision, the cover should be attached to the brackets when not in use.
  • Page 48 Controls and features 3. Fold vinyl edges towards center, making sure that the edges clear the end cap slots. Use tape or rubber band to hold the vinyl on the left side of the roller tube. 4. While holding the vinyl and roller tube, push in the right end cap (marked RH) about 6.4 mm (1/4 inch) to disengage the clutch.
  • Page 49 Keyless entry system (if equipped) With the keyless entry keypad, you can: lock or unlock the vehicle doors and liftgate without using the key. arm and disarm the anti-theft system. See also Remote entry system and Anti-theft system later in this chapter for more information.
  • Page 50 Controls and features presents them in a sequential order. Press the middle of the buttons (there is only one switch under each button). You can use either code to unlock your vehicle. If a second personal code is entered, the module will erase the old code in favor of the new code.
  • Page 51 locking the doors and liftgate. To lock the doors: press 7/8 and 9/0 buttons at the same time. This will arm your anti-theft system; see Arming anti-theft system with keyless entry and Anti-theft system later in this chapter for more details. Arming anti-theft system with keyless entry To arm the anti-theft system:...
  • Page 52 Controls and features Relock The autolock feature will repeat when: any door is opened and closed. the brake pedal is released. Deactivating autolock Before following the activation or deactivation procedures, make sure that the anti-theft system is not armed, ignition is off, and all vehicle doors and liftgate window are closed.
  • Page 53 Controls and features Additional transmitters can be ordered from your dealer. Unlocking the doors with the remote entry system Press UNLOCK button to unlock driver door. The interior lamps will illuminate. Press UNLOCK a second time within 5 seconds to unlock all doors and liftgate.
  • Page 54 If you notice a decrease in operating range, replace the transmitter batteries. Replacement batteries can be purchased at most pharmacies or through your Ford or Lincoln-Mercury dealer. The transmitter is powered by two coin type three-volt lithium 2016 batteries. The operating range of the remote...
  • Page 55 Controls and features When installing new batteries, be sure to place the positive (+) side down as marked. Snap the two halves back together. Replacing lost transmitters If a transmitter is lost, take your vehicle’s transmitter to the dealer to have the remote entry system deprogrammed for the lost transmitter.
  • Page 56 Controls and features Anti-theft system (if equipped) When set, the anti-theft system protects against unauthorized entry into a locked vehicle. The ignition switch must be in the OFF position to arm the anti-theft system. Arming the anti-theft system Use one of the following methods to arm the system: Press the LOCK button on the remote entry transmitter (with...
  • Page 57 flash the headlamps, park lamps THEFT and the indicator in the instrument cluster. sound the horn. disable vehicle starting. The flashing exterior lamps and honking horn will shut off automatically after about 3 minutes. The lights and horn will remain off unless another unauthorized entry is attempted.
  • Page 58 Controls and features Delayed accessory Delayed accessory provides power to operate the power windows and power moon roof (if equipped) for 10 minutes after the ignition switch is turned to OFF. If either front door is opened during the 10 minute period the delayed accessory feature is disabled.
  • Page 59: Seating And Safety Restraints

    Seating and safety restraints FRONT BUCKET SEATS Adjusting manual seats Lift to move the seat forward or backward. Pull up to recline the seat.
  • Page 60 Seating and safety restraints Adjusting power seats (if equipped) Pull up to recline the seat. Press to tilt front and rear of seat up or down.
  • Page 61 Seating and safety restraints Press in the desired direction to raise or lower the seat, or to move the seat backward or forward. Push to increase (+) or decrease (-) lumbar support. + –...
  • Page 62 Seating and safety restraints Rear seat four-way head restraints (if equipped) Push the lock release button to raise or lower the head restraint. Push or pull head restraint to desired position. Folding rear seat If your vehicle is equipped with a built-in child seat, the seatback cannot be folded down unless the built-in child seat is fully stowed.
  • Page 63 Seating and safety restraints Return to upright 1. Push downward on upper outboard corner of seatback and hold. 2. Lift release handle upward to unlatch seat. 3. Rotate seatback upward until seatback latches in the upright position. You will hear a ‘‘click’’ when seatback locks.
  • Page 64 Seating and safety restraints To prevent the risk of injury make sure children sit where they can be properly restrained. It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed.
  • Page 65 Seating and safety restraints The outboard safety restraints in the vehicle are combination lap and shoulder safety belts. The front and rear seat passenger outboard safety belts have the two types of locking modes described below: Vehicle sensitive (Emergency) locking mode The vehicle sensitive mode is the normal retractor mode, allowing free shoulder belt length...
  • Page 66 Seating and safety restraints Automatic locking mode In this mode, the shoulder belt is automatically pre-locked; however, the belt will still retract to remove any slack in the shoulder belt. The automatic locking mode is not available on the driver safety belt. When to use the automatic locking mode When a tight lap/shoulder belt...
  • Page 67 Seating and safety restraints 2. Grasp the shoulder belt portion and pull downward until the entire belt is extracted. 3. Allow the belt to retract. As the belt retracts, you will hear a clicking sound. This indicates that the safety belt is now in the automatic locking mode.
  • Page 68 Seating and safety restraints 1. To lower shoulder belt height, push the button and slide down. 2. To raise the height of the shoulder belt, push the button and slide up. 3. Pull down on the height adjustment assembly to make sure it is locked in place.
  • Page 69 Seating and safety restraints SAFETY BELT WARNING AND INDICATOR CHIME warning light illuminates in the instrument cluster and a chime sounds to remind the occupants to fasten their safety belts. Conditions of operation If... The safety belt is not buckled before the ignition key is turned to ON...
  • Page 70 Lincoln-Mercury recommends that all safety belt assemblies used in vehicles involved in a collision be replaced. However, if the collision was minor and a qualified...
  • Page 71 Seating and safety restraints Safety belt extension assembly For some people, the safety belt may be too short even when it is fully extended. You can add about 20 cm (8 in) to the belt length with a safety belt extension assembly (part # 611C22).
  • Page 72 Do not attempt to service, repair, or modify the air bag supplemental restraint system or its fuses. See your Ford or Lincoln-Mercury dealer. Rear-facing child seats or infant carriers should never be placed in the front seat. Air bags and air bag equipped vehicles should be disposed of only by your dealer.
  • Page 73 Seating and safety restraints AIR BAG DESCRIPTION The air bag system activates in collisions more severe than hitting a parked vehicle of similar size and weight head-on at about 45km/h (28 mph). The air bag system consists of two parts: The driver air bag in the middle of the steering wheel and the passenger air bag near the glove...
  • Page 74 Seating and safety restraints bags, and the air bags deflate. You may notice smoke and smell the escaping gas after the air bags deflate. This is normal. You and your passenger must wear your safety belts in order for the air bag system to operate effectively.
  • Page 75 Seating and safety restraints Never let a passenger hold a child on his or her lap while the vehicle is moving. The passenger cannot protect the child from injury in a collision. Always follow the instructions and warnings that come with any infant or child restraint you might use.
  • Page 76 Seating and safety restraints If the child is the proper size, restrain the child in a safety seat. CHILDREN AND INFANT OR CHILD SAFETY SEATS Carefully follow all of the manufacturer’s instructions included with the safety seat you put in your vehicle. If you do not install and use the safety seat properly, the child may be injured in a sudden stop or...
  • Page 77 Seating and safety restraints Installing child safety seats in combination lap and shoulder belt seating positions 1. Position the child safety seat in a seat with a combination lap and shoulder belt. If you choose to install a child safety seat in the front passenger seat, move the seat as far back as possible.
  • Page 78 Seating and safety restraints 3. While holding the shoulder and lap belt portions together, route the tongue through the child seat according to the child seat manufacturer’s instructions. Be sure the belt webbing is not twisted. 4. Insert the belt tongue into the proper buckle for that seating position until you hear and feel the latch engage.
  • Page 79 Seating and safety restraints 7. Pull the lap belt portion across the child seat toward the buckle and pull up on the shoulder belt while pushing down on the child seat. 8. Allow the safety belt to retract to remove any slack in the belt. 9.
  • Page 80 Seating and safety restraints strap. Contact the manufacturer of your safety seat for information about ordering a tether strap if one is not provided to you. Contact your Ford dealer for a free tether anchor kit (613D74) so you can attach a tether anchor bracket to the tether anchor attachment locations in the rear floor.
  • Page 81 Seating and safety restraints instruction under Installing child safety seats in combination lap and shoulder belt seating positions in this chapter. 4. Hook the tether strap around the webbing near the center of the shoulder portion of the rear safety belt and tighten.
  • Page 82 Seating and safety restraints Placing your child in the built-in child seat Failure to follow all of the instructions on the use of this child restraint system can result in your child striking the vehicle’s interior during a sudden stop or crash. Never use the built-in child seat as a booster cushion with the adult safety...
  • Page 83 Seating and safety restraints 2. Pull both Velcro straps to release child seat cushion. 3. Lower child seat cushion.
  • Page 84 Seating and safety restraints 4. Unfold cushion protector flap onto adult seat cushion. 5. If connected, disconnect the chest clip and buckles. 6. Place the child in the seat and position the left shoulder belt over the child’s left shoulder first, then place the right shoulder belt over the child’s right shoulder.
  • Page 85 Seating and safety restraints 7. Insert the left and right safety belt tongues into the left and right slots of the crotch buckle. Verify that the indicator window on each tongue is green to ensure proper safety belt connections. If both tongues do not latch in the buckle, do not use the child seat.
  • Page 86 Seating and safety restraints 9. Pull on the safety belt tongues to ensure they are both securely latched. If they are not latched, repeat Steps 7 and 8. If necessary, the shoulder belts can be put in automatic locking mode (ALR) to limit the child’s movement in the child seat.
  • Page 87 Seating and safety restraints 2. Allow the shoulder belts to fully retract. Removing your child from the built-in child seat 1. Disconnect the chest clip by squeezing the release tabs together and pulling the two sides apart. 2. Press the release button on the crotch buckle.
  • Page 88 Seating and safety restraints 7. Press firmly on the top center of the built-in child seat head restraint to ensure it is stowed properly. Inspecting the built-in child seat after a collision All built-in child restraints, including seats, buckles, retractors, seat latches, interlocks, and attaching hardware should be inspected by a qualified dealer technician after...
  • Page 89: Starting Your Vehicle

    IMPORTANT SAFETY PRECAUTIONS Extended idling at high engine speeds can produce very high temperatures in the engine and exhaust system, creating the risk of fire or other damage. Do not park, idle, or drive your vehicle in dry grass or other dry ground cover. The emission system heats up the engine compartment and exhaust system, which can start a fire.
  • Page 90 Starting your vehicle 2. Make sure the headlamps and vehicle accessories are off. 3. Make sure the parking brake is set and the gearshift lever is in P (Park). 4. Turn the key to the ON position (without turning the key to START).
  • Page 91 CHECK GAGE UNLEADED FUEL ONLY DOOR AJAR RPM x 1000 BRAKE The above lights illuminate briefly. If a light fails to illuminate, have the vehicle serviced. If the driver’s safety belt is fastened, the light does not illuminate. STARTING THE VEHICLE After completing the steps under Preparing to start the vehicle: 1.
  • Page 92 Starting your vehicle seconds. If the engine does not start on the first attempt: 1. Turn the ignition key to LOCK and wait approximately 10 seconds. 2. Try starting the engine again. At temperatures above -12°C (10°F), do not hold the key in the START position longer than five seconds.
  • Page 93 2. Press the accelerator all the way to the floor and hold. 3. Turn the key to START. Release it once the engine starts. 4. Release the accelerator gradually as the engine speeds up. If the engine still does not start, refer to Fuel pump shutoff switch in the Roadside emergencies chapter.
  • Page 94 Starting your vehicle GUARDING AGAINST EXHAUST FUMES Carbon monoxide, although colorless and odorless, is present in exhaust fumes. Take precautions to avoid its dangerous effects. If you smell exhaust fumes inside your vehicle, have your dealer inspect your vehicle immediately. Do not drive if you smell exhaust fumes.
  • Page 95 Starting your vehicle Ventilating your vehicle If the engine is idling while the DOOR LOCK vehicle is stopped in an open area for long periods of time, open the windows at least 2.5 cm (1 inch). Adjust the heating or air conditioning to bring in fresh air.
  • Page 96: Driving

    Driving BRAKES The anti-lock brake system (ABS) Anti-lock brake operation differs slightly from standard brake operation. Apply the brakes steadily. DO NOT pump the brakes in a panic stop. The brake system will prevent wheel lockup by automatically releasing and reapplying the brakes.
  • Page 97 ABS warning light light in the instrument cluster illuminates and remains illuminated if an ABS fault is detected. Have your vehicle serviced as soon as possible. Normal braking operation is still effective unless the light is also illuminated. Parking brake The parking brake should be used whenever the vehicle is parked.
  • Page 98 Driving Pull release handle towards you to release parking brake. If the parking brake is fully released, but the warning light remains on, have the brakes checked immediately. They may not be working properly. AUTOMATIC TRANSMISSION OPERATION (4R70W) Hold the brake pedal down while you move the gearshift from position to position.
  • Page 99 Pull gearshift lever towards you and downward to move the automatic gearshift. P - Park Always come to a complete stop before shifting into or out of P (Park). Always set the parking brake fully and make sure that the gearshift is securely latched in P (Park).
  • Page 100 Driving - Overdrive The normal driving position for the best fuel economy. Transmission operates in gears 1-4. (Overdrive) can be disengaged by pressing the transmission control switch on the gearshift lever. The transmission control indicator light on instrument cluster will remain off. D - Drive Not shown on the display.
  • Page 101 Driving on downgrades. Transmission operates in gears 1-2. 1 - Low Use 1 (Low) to provide maximum engine braking on steep downgrades. Upshifts can be made by shifting to 2 (Second) or to (Overdrive). Selecting 1 (Low) at higher speeds causes a shift to 2 (Second), and will shift to 1 (Low) after vehicle decelerates to the proper speed.
  • Page 102 Driving Do not drive your vehicle until you verify that the brakelamps are working. If your vehicle gets stuck in the mud or snow it may be rocked out of the spot. To rock the vehicle out, shift between forward and reverse gears in a steady rhythm.
  • Page 103 features to make them capable of performing in a wide variety of off-road applications. Specific design characteristics give them higher centers of gravity than ordinary passenger cars. Utility and four-wheel drive vehicles are NOT designed for cornering at speeds as high as passenger cars any more than low-slung sports cars are designed to perform satisfactorily under off-road...
  • Page 104 Driving should either know the terrain or examine maps of the area before driving. Map out your route before driving in the area. For more information on driving off-road, read Four-Wheeling in your owner’s portfolio. Sand When driving over sand, try to keep all four wheels on the most solid area of the trail.
  • Page 105 Driving that could damage drive components. If the transmission and transfer case are submerged in water, their fluids should be checked and changed, if necessary. All rear axle lubricants must be replaced every 160,000 km (100,000 miles) or if the axle has been submerged in water.
  • Page 106 Driving heavy load. If vehicle speed drops more than 15 - 25 km/h (8 - 14 mph) the speed control will cancel automatically. Resume speed with accelerator pedal. If speed control cancels after climbing the hill, reset speed by pressing and holding the SET ACCEL button or returning to previous speed by pressing the RESUME button (to resume...
  • Page 107 between forward and reverse gears. DO NOT rock the vehicle for more than a few minutes. The transmission and tires may be damaged or the engine can overheat. Do not spin the wheels at over 55 km/h (35 mph). The tires may fail and injure a passenger or bystander.
  • Page 108 Driving Payload: Combined maximum allowable weight of cargo, passengers and optional equipment. The payload equals gross vehicle weight rating (GVWR) minus base curb weight. GVW (Gross Vehicle Weight): Base curb weight plus the payload weight (including passengers, cargo, and optional equipment).
  • Page 109 Maximum Trailer Weight Rating: Maximum weight of a trailer the vehicle is permitted to tow. The maximum trailer weight rating equals the vehicle curb weight for each engine/transmission combination, any required option weight for trailer towing and the weight of the driver from the GCWR for the towing vehicle.
  • Page 110 Driving Do not use replacement tires with lower weight capacities than the original because they may lower the vehicle’s GVWR and GAWR limitations. Replacement tires with a higher weight limit than the originals do not increase the GVWR and GAWR limitations. TRAILER TOWING Your vehicle may tow a Class I or II trailer provided the maximum...
  • Page 111 If the GVWR or the GAWR specified on the Safety Compliance Certification Label is exceeded, your vehicle may be damaged or you may lose control and injure someone. Towing trailers beyond the maximum recommended gross trailer weight exceeds the limits of the vehicle and could result in engine damage, transmission/axle damage, structural damage, loss of...
  • Page 112 Driving below the maximum shown under maximum trailer weight on the chart. Trailer Towing Table 4R70W Automatic Transmission Rear Maximum Engine Axle GCWR kg (lb) Ratio 2-Wheel Drive 5.0L 3.73 4,990 (11,000) All-Wheel Drive 5.0L 3.73 4,990 (11,000) For high altitude operation, reduce GCWR by 2% per 300 meters (1,000 ft) elevation.
  • Page 113 bumper has a Class II rating (1590 kg/3500 lb trailer weight and 159 kg/350 lb tongue weight). Safety chains Always connect the trailer’s safety chains to the vehicle. To connect chains when towing with the step bumper, cross the chains under the trailer tongue and allow slack for turning corners.
  • Page 114 Driving Trailer lamps Trailer lamps are required on most towed vehicles. Make sure your trailer lamps conform to Federal and local regulations. See your dealer or trailer rental agency for the proper instructions and equipment for hooking up trailer lamps. Do not hook the trailer lamps directly into the vehicle’s lighting system wiring.
  • Page 115 Servicing while towing If you tow a trailer for long distances, your vehicle will require more frequent service intervals. Refer to the Service Guide for more information. Trailer towing Practice turning, stopping and backing in an area before starting on a trip to get the feel of the vehicle/trailer combination.
  • Page 116 Driving Luggage rack (if equipped) Load luggage as far back as it will safely go without loading more than 45 kg (100 lb) or cause the vehicle to exceed the Gross Vehicle Weight Rating (GVWR) or its Gross Axle Weight Rating (GAWR).
  • Page 117 Driving sudden stops extended engine idling use of speed control in hilly terrain extended use of the air conditioner, defroster, rear window defroster and other accessories underinflated tires heavy loads aftermarket add-ons such as bike, ski or luggage racks, bug deflectors, etc.
  • Page 118: Roadside Emergencies

    Roadside emergencies HAZARD SWITCH Use the hazard flashers to warn traffic of vehicle problems. Press button down to activate hazard flashers. Press button again to deactivate hazard flashers. FUEL PUMP SHUTOFF SWITCH The fuel pump shutoff switch stops the fuel pump when the vehicle has been involved in a collision or major jolt.
  • Page 119 Press the red button to reset the fuel pump. FUSES AND RELAYS Fuses If electrical components in the vehicle are not working, a fuse may have blown. Blown fuses are identified by a broken wire. Check the appropriate fuses before replacing any electrical components.
  • Page 120 Roadside emergencies Standard fuse amperage rating and color Fuse Rating 7.5 amp 10 amp 15 amp 20 amp 30 amp 30 amp fuse link 40 amp 60 amp fuse link 80 amp fuse link 100 amp fuse link Even after a fuse is replaced, it will continue to blow if the cause of the overload is not identified and corrected.
  • Page 121 Use the fuse puller tool provided on the passenger compartment fuse panel cover to replace fuses. Number Fuse Amperage Rating 7.5 amp 7.5 amp 15 amp 10 amp 10 amp 7.5 amp Roadside emergencies Circuits Protected Power mirror, power antenna High-mount brakelamp Parking lamps...
  • Page 122 Roadside emergencies Number Fuse Amperage Rating 7.5 amp 10 amp 10 amp 7.5 amp 7.5 amp 10 amp 15 amp 10 amp 7.5 amp 30 amp 15 amp 15 amp 25 amp 7.5 amp 15 amp 10 amp 10 amp 10 amp 7.5 amp Circuits Protected...
  • Page 123 Number Fuse Amperage Rating 10 amp 10 amp 7.5 amp 10 amp 7.5 amp 7.5 amp 15 amp 7.5 amp Roadside emergencies Circuits Protected 4R70W overdrive, DRL system, backup lamps, rear defroster relay Underhood lamp, map lights, glove box lamp, overhead lamp, visor lamps, accessory delay, dimmer switch...
  • Page 124 Roadside emergencies Power distribution box Lift cover towards front of vehicle to access the power distribution box. The high-current fuses in the power distribution box protect your vehicle’s main electrical systems from overloads. The high current fuses are coded as follows: 11 10 9...
  • Page 125 High Current Fuse Rating 20 amp 30 amp 40 amp 50 amp 60 amp Always disconnect the battery before servicing high current fuses. Always replace the cover to the power distribution box before reconnecting the battery or refilling fluid reservoirs. Maxi fuses Fuse Amps...
  • Page 126 Roadside emergencies Fuse Amps 30 amp 50 amp 30 amp 20 amp 60 amp 60 amp Fuse Amps 30 amp 15 amp 30 amp 10 amp Maxi fuses Circuits protected Battery saver relay, headlamp relay Blower motor relay, blower motor Power seats, power lumbar, door lock/unlock relays,...
  • Page 127 Fuse Amps 15 amp 20 amp 15 amp 20 amp Relays Relays are located in the power distribution box. Relays receive signals from components or systems and transfer these signals to activate or deactivate other components or systems. Mercury recommends that relays be replaced by a qualified technician.
  • Page 128 Roadside emergencies Relay number Circuits connected Wiper run relay Horn relay Wiper HI/LO relay WOT A/C relay PCM power relay Fuel pump relay Diode number Circuits connected ABS diode PCM diode CHANGING TIRES Tire change procedure 1. Park on a level surface. 2.
  • Page 129 Roadside emergencies 7. Remove the jack handle (located underneath rear seat). 8. Assemble the jack handle to the lug wrench. 9. Insert drive section of the jack handle into the actuator hole and turn counterclockwise until the cable is slack enough to allow spare tire to be pulled rearward from under the vehicle.
  • Page 130 Roadside emergencies 11. Insert tapered end of the lug nut wrench behind hubcaps and twist off. Not using the tapered end of the lug nut wrench at the pry-off notches may result in damage to the finish of the wheel and ornament. 12.
  • Page 131 Position the jack under the rear axle to raise the rear wheel. 14. Turn the jack handle clockwise and raise the vehicle until the tire just clears the ground. 15. Remove the wheel lug nuts and flat tire, and install the spare. 16.
  • Page 132 Roadside emergencies To stow largest flat tire, place inside vehicle and secure with webbing retainer. JUMP STARTING A DISABLED VEHICLE The gases around the battery can explode if exposed to flames, sparks, or lit cigarettes. An explosion could result in injury or vehicle damage.
  • Page 133 vegetable oil. Call a doctor immediately. To avoid damage or injury, follow these directions in the order they are given. If in doubt, call for road service. Before jump starting a vehicle: Make sure the booster battery vehicle has a 12-volt starting system (a 24-volt power supply will cause vehicle damage).
  • Page 134 Roadside emergencies Do not connect the end of the second cable to the negative (-) terminal of the battery to be jumped. A spark may cause an explosion of the gases that surround the battery. 5. Start the engine in the vehicle with the booster battery.
  • Page 135 Roadside emergencies WRECKER TOWING It is recommended that your vehicle be towed with wheel lift and dollies or flatbed equipment. Do not tow with slingbelt equipment. Ford Motor Company has not developed or approved a T-hook or slingbelt towing procedure.
  • Page 136: Maintenance And Care

    Maintenance and care SERVICE RECOMMENDATIONS Whenever possible, Ford has designed parts that do not require servicing. However, when servicing is required, Ford’s goal is to make servicing your vehicle as easy as possible. To help you: We highlight do-it-yourself items in the engine compartment for easy location.
  • Page 137 come on unexpectedly; always turn the engine off and let it cool. The cooling fan is automatic and may come on at any time. Always disconnect the negative terminal of the battery before working near the fan. Never get under a vehicle supported only by a jack.
  • Page 138 Maintenance and care Working with the engine on 1. Set the parking brake and make sure that the gearshift is securely latched in P (Park). 2. Do not work on a vehicle in an enclosed space with the engine running. 3.
  • Page 139 IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT Engine coolant recovery reservoir Windshield washer reservoir Engine oil filler tube Automatic transmission dipstick Brake master cylinder Power distribution box Maintenance and care 5.0L Battery Radiator cap Power steering fluid reservoir Engine oil dipstick Ignition coil packs Air cleaner...
  • Page 140 Maintenance and care CHECKING AND ADDING ENGINE OIL Use WSS-M2C153-F motor oil CERTIFIED FOR GASOLINE ENGINES by the American Petroleum Institute. Engine oils with an SAE 5W–30 viscosity and displaying the American Petroleum Institute certification mark are preferred for your vehicle. They provide the best engine performance, fuel economy and engine protection for all climates down to –25°C (–15°F).
  • Page 141 Maintenance and care Checking the engine oil Check the engine oil every time you fuel your vehicle. Check the engine oil level more frequently if the vehicle is carrying a heavy load, towing a trailer, idling for extended periods (like police, taxi, or shuttle service vehicles), or driven at high speeds for extended periods of time.
  • Page 142 Maintenance and care Adding engine oil If the fluid level is below the MIN line, add engine oil. Add engine oil through the oil filler cap and use a funnel to pour oil into the opening. Make sure you use a certified engine oil of the preferred viscosity.
  • Page 143 1. Clean the reservoir cap before removal to prevent dirt or water from entering the reservoir. 2. Visually inspect the fluid level. 3. If necessary, add brake fluid until the level reaches within 1/8 of the MAX line on the reservoir. Do not exceed MAX.
  • Page 144 Maintenance and care CHECKING AND ADDING WASHER FLUID Visually inspect the fluid level in the washer fluid reservoir. If washer fluid needs to be added to the reservoir: 1. Lift the washer fluid reservoir cover. 2. Add enough washer fluid to fill the reservoir.
  • Page 145 Checking and adding washer fluid for the liftgate The opening for this reservoir is located on the left side of the vehicle above the tail lamp. Be sure to close the cover after filling and before closing the liftgate. The reservoir must be filled slowly to allow trapped air to escape.
  • Page 146 Maintenance and care or 80,000 km (50,000 miles). It is not necessary and not recommended to use supplemental coolant additives in your gasoline-powered vehicle. These additives may harm your engine cooling system. When you change or add engine coolant, it is important to maintain your engine coolant concentration between 40% (-24°C [11°F]) and 60% (-52°C [-62°F]), depending on...
  • Page 147 Maintenance and care 1. Before you remove the coolant recovery cap, turn the engine off and let it cool. Even when the engine is cool, be careful when removing the recovery cap. Wrap a thick cloth around the cap for safe removal.
  • Page 148 Maintenance and care Checking the cooling system hoses Before adding or replacing coolant, inspect all cooling system hoses for: deterioration leaks loose clamps CHECKING AND ADDING POWER STEERING FLUID Check the power steering fluid at least twice a year by completing the following steps: 1.
  • Page 149 3. Visually inspect the fluid level in the power steering reservoir. 4. If necessary, add power steering fluid until the fluid level reaches MAX. Do not overfill the power steering reservoir. As a maintenance precaution, visually inspect the lines and hoses of the power steering system for leaks and damage.
  • Page 150 Maintenance and care Your vehicle does not use up transmission fluid. However, it is recommended that you check the transmission fluid at least twice a year. The fluid level should be checked if the transmission is not working properly, i.e., the transmission slips or shifts slowly or if you notice some sign of fluid leakage.
  • Page 151 6. Remove the dipstick and inspect the fluid level. The fluid level should be within the crosshatched area, or if the vehicle has not been driven, between the holes near the bottom of the indicator. 7. If necessary, add fluid in .25 L (1/2 pint) increments through the filler tube until the level is at the correct area on the dipstick.
  • Page 152 Maintenance and care Checking and adding transfer case fluid 1. Clean the filler plug. 2. Remove the filler plug and inspect the fluid level. 3. Fluid level should be at the bottom of the opening. When adding transfer case fluid: Use fluid certified to meet Ford Motor Company lubricant specifications.
  • Page 153 Add only enough fluid through the filler opening so that the fluid level is at the bottom of the opening. BATTERY If the original equipment maintenance-free battery needs replacing, it may be replaced with a low-maintenance battery. For information on replacement batteries, refer to Motorcraft part numbers in the Capacities and specifications chapter.
  • Page 154 Maintenance and care the electrolyte level and adding water. Check the electrolyte level every 24 months or 40,000 km (24,000 miles) in average temperatures 32°C (90°F). Keep the electrolyte level in each cell up to the level indicator. Do not overfill.
  • Page 155 3. Let the engine idle for at least one minute. 4. The relearning process will automatically complete as you drive the vehicle. If you do not allow the engine to relearn its idle, the idle quality of your vehicle may be adversely affected until the idle is eventually relearned.
  • Page 156 Maintenance and care Changing your air filter 1. Loosen the clamp that secures the air cleaner in place. Separate the two halves of the air cleaner. 2. Remove the air filter element from the open end of the engine air cleaner and replace it with a new element.
  • Page 157 Maintenance and care To make reaching the wiper blades easy, simply turn the ignition to the ON position and turn the wipers on. Wait for them to reach a vertical position and turn the ignition to LOCK. Do not move the wipers manually across the windshield as this may cause damage to the wipers.
  • Page 158 Maintenance and care on wiper blade until lock tab is engaged. To replace liftgate wiper blade: 1. Pull wiper arm away from liftgate window. 2. Use small screwdriver to depress lock tab and pull wiper blade upwards and away from wiper arm.
  • Page 159 grades exactly as the government has written it. Treadwear The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire graded 150 would wear 1 ⁄...
  • Page 160 Maintenance and care Temperature A B C The temperature grades, from highest to lowest, are A, B and C. These grades represent the tire’s resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel.
  • Page 161 when tires are cold (after the vehicle has been parked for at least one hour or driven less than 5 km (3 miles). The cold pressure amount is listed on the Safety Compliance Certification Label located on the inside driver’s door latch pillar. Improperly inflated tires can affect vehicle handling and can fail suddenly, possibly...
  • Page 162 Maintenance and care Four tire rotation Five tire rotation Replacing the tires Replace the tires when the wear band is visible through the tire treads. When replacing full size tires, never mix radial bias belted or bias-type tires. Use only the tire sizes that are listed on the tire pressure decal.
  • Page 163 Failure to follow these precautions may adversely affect the handling of the vehicle and make it easier to lose control and roll over. IDENTIFYING TIRE TYPES Refer to the Safety Compliance Certification Label to determine the specific size tire and wheel Ford Motor Company recommends for use on this vehicle.
  • Page 164 Maintenance and care Drive cautiously. If you hear the chains rub or bang against your vehicle, stop and re-tighten the chains. If this does not work, remove the chains to prevent damage to your vehicle. If possible, avoid fully loading your vehicle.
  • Page 165 If you replace your fuel cap with an aftermarket fuel filler cap, the customer warranty may be void if any damage to the fuel tank and/or fuel system occurs. If the fuel cap is venting vapor or you hear a hissing sound, wait until it stops before completely removing the cap.
  • Page 166 Fuel quality If you are experiencing starting, rough idle or hesitation problems try a different brand of fuel. If the condition persists, see your dealer or a qualified service technician. The American Automobile Manufacturers Association (AAMA)
  • Page 167 Maintenance and care issued a gasoline specificaton to provide information on high quality fuels that optimize the performance of your vehicle. We recommend the use of gasolines that meet the AAMA specification if they are available. It should not be necessary to add any aftermarket products to your fuel tank if you continue to use a high-quality fuel.
  • Page 168 Maintenance and care Calculating fuel economy 1. Fill the tank completely and record the initial odometer reading. 2. Each time you fill the tank, record the amount of fuel added (in liters or gallons). 3. After at least three to five fuel tank fill-ups, fill the fuel tank and record the final odometer reading.
  • Page 169 your vehicle to comply with applicable exhaust emission requirements. For more information on your vehicle’s emission control system, see the Vehicle Emission Control Information decal located on the left side of the engine compartment. Follow these guidelines to ensure proper emission system operation: Use only unleaded fuel.
  • Page 170 Maintenance and care If you notice one or more of the following, the emission system may not be working properly. Have the vehicle serviced as soon as possible. Fluid leaks. CHECK lights ENGINE illuminate in the instrument cluster and remain lit. Strange odors.
  • Page 171 Preparing your vehicle for inspection/maintenance testing In some localities it may become a legal requirement to pass an Inspection/Maintenance test of the On-Board Diagnostic (OBD II) system. If the vehicle’s powertrain system or battery has just been serviced, the OBD II system is reset to a not ready for I/M testing condition.
  • Page 172 Maintenance and care EXTERIOR LAMPS Replacing the exterior bulbs It is a good idea to check the operation of the following lights frequently: Headlamps High-mount brakelamp Tail lamps Brakelamps Backup lamps Hazard flasher...
  • Page 173 Turn signals License plate lamp Fog lamps Interior overhead lamp Do not remove lamp bulbs unless they will be replaced immediately. If a bulb is removed for an extended period of time, contaminants may enter the lamp housings and affect performance. Headlamps Handle a halogen bulb carefully and keep out of...
  • Page 174 Maintenance and care 3. Remove electrical connector by grasping wires and pulling rearward. 4. Remove bulb retaining ring by turning it 1/8 turn to free it from the socket. Slide the ring off the plastic base. 5. Carefully remove the bulb assembly from its socket by gently pulling it rearward.
  • Page 175 Maintenance and care remove and replace any of the bulbs. 1. Remove the two (2) screws retaining rear lamp to vehicle. 2. Remove rear lamp by pulling rearward to disengage two lower barbed retainers. 3. Remove socket from lamp. 4. Remove bulb from socket. 5.
  • Page 176 Maintenance and care Turn signals For more information on the turn signals, refer to Turn signals in the Controls and Features chapter. For bulb replacement, see your dealer. License plate lamp To change the license plate bulb, follow this procedure: 1.
  • Page 177 Maintenance and care Fog lamps 1. Disconnect the electrical connector from the back of the foglamp by turning it counterclockwise. 2. Remove bulb by lifting retaining clip and pulling the bulb from the assembly. 3. Replace the bulb and insert the bulb assembly back into the foglamp.
  • Page 178 Maintenance and care 1. To remove the lens, pry with a small screwdriver as shown. LAMP MODE LAMP 2. To remove the bulbs, rotate bulb holder counterclockwise 90°. The bulb and bulb holder will drop out. LAMP MODE LAMP 3. Pull bulb from bulb holder. Insert new bulb.
  • Page 179 BULB SPECIFICATIONS Description Exterior Illumination Headlamps Front lamp and turn signal Front side marker lamp Underhood lamp Fog lamps Rear Lamps - Exterior Rear back-up lamp High-mount brakelamp License plate lamp Rear tail/brake lamp Turn lamp Interior Courtesy Lamps Cargo lamp Dome lamp (low series) Dome lamp (high series) Map lamps...
  • Page 180 Instrument Panel Controls A/C controls Rear window wiper/washer control Headlamp controls Heater controls Replaceable at Lincoln/Mercury and Ford authorized radio service centers. See your dealer for bulb replacement. * Natural amber Aiming headlamps The alignment of your headlamps should be checked if:...
  • Page 181 Maintenance and care See your Lincoln/Mercury or Ford dealer for precise adjustment of your headlamps. CLEANING AND CARING FOR YOUR VEHICLE Washing your vehicle Wash your vehicle regularly with cold or lukewarm water. Never use strong detergents or soap. If your vehicle is particularly dirty, use a quality car wash detergent.
  • Page 182 Maintenance and care warranty on paperwork, remove aggressive particles such as bird droppings, tree sap, insect remains, tar spots, road salt, and industrial fallout immediately. Cleaning the wheels Wash the wheels with the same detergent you use to clean the body of your vehicle.
  • Page 183 Cleaning the engine A clean engine is more efficient than a dirty one because a buildup of grease and dirt acts as an insulator and keeps the engine warmer than normal. Follow these guidelines to clean your engine: Take care when using a power washer to clean the engine.
  • Page 184 Maintenance and care Cleaning the built-in child seat Clean the built-in child seat with mild soap and water. Do not use household cleaning products because they may weaken the safety belt webbing or damage the vinyl parts of the seat. The child seat liner is removable and may be machine-washed and air dried.
  • Page 185: Capacities And Specifications

    Capacities and specifications MOTORCRAFT PART NUMBERS Component Motorcraft part number Spark plug AWSF-32EE* Air filter FA-1641 Fuel filter FG-872 Oil filter FL-1A Battery BXT-65-650 or BXT-65-850 (optional) P.C.V. valve EV-152 Refer to Vehicle Emission Control Information Decal for spark plug and gap specifications.
  • Page 186 Capacities and specifications Fluid Component Transfer case fluid (if Borg Warner AWD equipped) transfer case Transmission fluid, Automatic 4R70W automatic (2WD and AWD) Windshield washer Front washer fluid fluid, front reservoir Windshield washer Liftgate washer fluid fluid, rear reservoir Fill to 6-15 mm (1/4 to 9/16 ) from the bottom of the filler hole. Includes 1 L (1 qt.) for filter replacement.
  • Page 187 Capacities and specifications LUBRICANT SPECIFICATIONS Ford part Component name Windshield Ultra-Clear washer Windshield reservoir Washer Concentrate Body hinges, Multi-Purpose latches, door Grease striker plates and rotors, seat tracks, door checks and tracks, hood latch, auxiliary latch, and fuel filler door and spring Steering Premium...
  • Page 188 Capacities and specifications Ford part Component name Engine oil Motorcraft Motor Oil 5W-30 Super Premium Door Silicone weatherstrips Lubricant Automatic Premium transmission Long-Life shift linkage Grease and brake pedal shaft Automatic Motorcraft transmission MERCON ATF 4R70W Power steering Motorcraft reservoir MERCON ATF Parking brake Speedometer...
  • Page 189 Capacities and specifications Ford part Component name Engine coolant Premium Cooling System Fluid Transfer case Premium front output Long-Life slip shaft Grease Transfer case Motorcraft MERCON ATF Dana 35 front 4x4 Gear Oil drive axle Add 118 ml (4oz.) of EST-M2C118-A Friction Modifier (part number C8A2-19B546-A) for complete refill of Ford Traction-Lok rear axles.
  • Page 190 Capacities and specifications VEHICLE DIMENSIONS Dimensions A = Overall height B = Track front/rear C = Overall width (excluding mirrors) D = Wheelbase E = Overall length 1.83 m (67.3 in.) 1.49 m (58.3 in.) 1.87 m (70.2 in.) 2.83 m (111.9 in.) 4.78 m (184.3 in.)
  • Page 191 Capacities and specifications VEHICLE IDENTIFICATION NUMBER (VIN)
  • Page 192: Reporting Safety Defects

    Reporting safety defects If you believe that your vehicle has a defect which could cause a crash, or could cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying Ford Motor Company. If NHTSA receives similar complaints, it may open an investigation, and if it finds that a...
  • Page 193: Index

    Air bag supplemental restraint system ...71,74,75,76,77,82,87 and child safety seats ...74,76,77,82,87 description ...73 indicator light ...74 Air cleaner filter replacing ...156 All Wheel Drive ...102 Anti-theft system ...56 arming the system ...56 disarming a triggered system ..57 disarming an untriggered system ...57 Audio system (see Electronic sound system) ...16...
  • Page 194 Index Flat tire ...131 Fluid refill capacities ...185 Foglamps ...16,177 Fuel calculating fuel economy ...167 choosing the right fuel ...166 improving fuel economy ...116 safety information relating to automotive fuels ...164 Fuel gauge ...7 Fuel pump shut-off switch ..16,118 Fuse panels ...120 power distribution box ...124 Fuses ...119 charts ...120...
  • Page 195 Parts (see Motorcraft Parts) ...185 Power door locks ...38 Power steering fluid, checking and adding ...148 Rear climate control system ...45 Refill capacities for fluids ...185 Relays ...127,128 Remote entry system arming and disarming the anti-theft system ...52,54 locking/unlocking doors ...53 panic alarm ...53 replacement/additional transmitters ...55...
  • Page 196 Index Windshield defrosting ...21 Windshield washer fluid and wipers checking and replacing wiper blades ...156 operation ...24...
  • Page 197: Filling Station Information

    Filling station information Fuel info Unleaded only - 87 octane Fuel tank capacity 79.5 L (21.0 gal) Engine oil Use only oil displaying the American Petroleum specifications Institute Certification Mark SAE 5W-30 Tire size and See Safety Compliance Certification Label on inside of driver door pressure Hood release...

This manual is also suitable for:

1997

Table of Contents