Surround; Tuner; Video - Marantz SR3053 User Manual

TROUBLESHOOTING

SURROUND

Symptom Cause
There is no sound
No sound has been recorded on
from a certain
that channel.
speaker.
The Surround mode is set to
STEREO.
There is no sound
from the center
speaker.
CENTER = NONE (CNTR = NONE)
is selected on the SPEAKER SIZE
menu.
The Surround mode is set to
STEREO.
There is no sound
from the surround
speakers.
SURROUND = NONE (SURR
= NONE) is selected on the
SPEAKER SIZE menu.
• The subwoofer is not turned on.
• The subwoofer level is too low.
• SUBWOOFER = NO (SUB
There is no
sound from the = NONE) is selected on the
subwoofer. SPEAKER SIZE menu.
The playback source does not
contain any sound in the low range.
Night mode does
not function. (Only A source that is not recorded in
applies to units Dolby Digital is being played.
with Night mode)
Cannot select the The Surround modes available are
Surround mode limited by input signal and speaker
that I want. settings.
• The unit is connected using an
analog connection.
• The player is conducting search
A noise is playback.
generated during
playback of DTS-
encoded CDs, etc.
• Some inappropriate digital
processing (level adjustment,
change of sampling frequency,
etc.) is happening in the player.
Cannot play back • The digital signal output of the
audio like Dolby player, etc., is set to PCM.
Digital or DTS.
• The unit is connected using an
(Indicator does not
analog connection.
light up)
24
Solution Page
Check the channel status of the
26
input signal.
When the Surround mode is set to
STEREO, no sound will come from
26
the center speaker. Set the unit to
another Surround mode.
Set CENTER to SMALL (SML) or
16, 17
LARGE (LRG).
When the Surround mode is set to
STEREO, no sound will come from
26
the surround speakers. Set the unit
to another Surround mode.
Set SURROUND to SMALL (SML)
16, 17
or LARGE (LRG).
• Turn on the power to the subwoofer. –
• Raise the subwoofer level. 17
• Select SUBWOOFER = YES 16, 17
(SUB = YES).
–
Use a source recorded in Dolby
–
Digital.
See the Surround mode table. 26
• Use a digital connection (optical 9, 10
or coaxial).
• Noise may occur during search –
playback depending on the
component. There is nothing
wrong with the unit.
• See the player's instruction –
manual.
• See the instruction manual of the –
player, etc.
• Use a digital connection. 9, 10
Symptom Cause
When playing a CD
on a DVD player, Depending on the player, the digital
the next track is signal may be interrupted when a
played with part track is skipped. The start of the
of the beginning song may be slightly interrupted in
missing when track order to determine the surround
skipping, etc., is system.
conducted.

TUNER

Symptom Cause
Cannot receive The antennas are not completely
AM or FM signals. connected.
A noise is
generated when The unit is getting interference
receiving an AM from other equipment.
signal.
A noise is
generated when The signal from the broadcasting
receiving an FM station is weak.
signal.

VIDEO

Symptom Cause
• The monitor TV connection,
input switching, etc., are not set
up correctly.
No image on the
• The unit has an HDMI
video monitor TV.
connection to the source
component, but no HDMI
connection to the monitor TV.
The audio or
the image does The input cables are not correctly
not match the connected.
selected source.
• The video recording component
jack does not match the source
component jack.
Cannot record to a
VCR, etc.
• A copy-protected signal is being
received.
Solution Page
If using such a DVD player, you
can play back the audio without
9, 10
problem by using an analog
connection.
Solution Page
Make sure the AM antenna
and FM antenna are properly
12
connected to the AM and FM
antenna terminals, respectively.
Change the location of the AM
12
antenna.
Put up an outdoor FM antenna. 12
Solution Page
• See the monitor TV's instruction 10
manual.
• Make an HDMI connection to 11
the monitor TV.
Connect the cables properly,
referring to the connection 10, 11
diagram.
• Make sure the recording 10
component jack matches the
source component jack.
• Video signals that include copy- –
protected signals cannot be
recorded.