Download
Share
Print this page
Baja motorsports SC50-2 Setup Instructions
  1. Manuals
  2. Brands
  3. Baja motorsports Manuals
  4. Scooter
  5. SC50-2
  6. Setup instructions
Baja motorsports SC50-2 Setup Instructions

Baja motorsports SC50-2 Setup Instructions

Scooter
Hide thumbs Also See for SC50-2:

Advertisement

Quick Links

Download this manual See also: Owner's Manual
SC50-2 Scooter Set up Instructions
Removal from Crate
1. Remove cardboard carton
2. Remove wire straps and foam
from metal frame.
covering from handlebars.
4. Remove axle bolt holding metal
3. Remove bolt holding metal
frame to front forks.
frame to rear of scooter.
Rev C
051908

Advertisement

loading

Related Manuals for Baja motorsports SC50-2

Summary of Contents for Baja motorsports SC50-2

  • Page 1 SC50-2 Scooter Set up Instructions Removal from Crate 1. Remove cardboard carton 2. Remove wire straps and foam from metal frame. covering from handlebars. 4. Remove axle bolt holding metal 3. Remove bolt holding metal frame to front forks. frame to rear of scooter.

  • Page 2: Removal From Crate

    Removal from crate NOTE: Pay attention to front wheel spacer. Save this spacer for installation of front wheel 5. Remove metal frame and parts included for assembly. Parts QTY 1 QTY 4 Front wheel spacer Front fender Front wheel QTY 1...
  • Page 3 Parts Parts listed below found under seat Manufacturer Certificate Owners Manual of Origin Mirrors Tool Kit Floorboard cover/mat Battery Box...

  • Page 4: Front Wheel

    Front Wheel Axle bolt Alignment groove on front fork Speed sensor Alignment tab on 6. Align speed sensor between speed sensor front wheel and front fork. Front wheel 7. Place front wheel spacer between disc spacer brake and fork on axle bolt. Attach front wheel with axle bolt provided.
  • Page 5 Handlebar Bolt Handlebar stem 9. Attach handlebar assembly to stem using bolt and nut provided. Open end wrench NOTE: For easy installation place nut on open end wrench.
  • Page 6 Kick Stand 10. Remove cotter pin from kick stand bolt 11. Attach kick stand to bottom of engine Remove bolt. Save both cotter pin and using bolt previsouly removed. bolt for installation. 13. Attach both kick stand springs. 12. Secure kick stand bolt using cotter NOTE: Place small spring inside big spring.

  • Page 7: Turn Signals

    Mirrors 14. Insert left and right mirror into hole on handlebar and turn clockwise, secure by tightening nut . Turn Signals 15. Attach left and right turn signals to bracket located on handlebars.
  • Page 8 Horn and Front Fender Green wire Purple wire 16. Connect the purple and green wire to post on horn. NOTE: It does not matter which post either wire is connected to. 17. Attach front fender. Line up tabs of fender with slots on scooter.
  • Page 9 Rear Luggage Carrier Bolt 1 18. Secure rear luggage carrier using hardware provided. NOTE: You will only need to install two of the three bolts as bolt 1 is installed from the factory for shipping purposes.

  • Page 10: Battery Installation

    Battery Installation Battery located in floorboard under mat. 19. Refer to battery section of owners manual for correct installation and charging of battery. WARNING The following procedure is very dangerous and should be performed with utmost care and attention. Wear protective eyewear, rubber gloves, and have water available should electrolyte come in contact with skin or eyes.
  • Page 11 Battery Installation Note: The following page is for vehicles with battery’s containing separate electrolyte pack. Most battery’s will come with the electrolyte already sealed into the battery. Preparing the battery: · Place battery on level surface. Remove sealing tape from top. (see figure 20) ·...
  • Page 12 Battery Installation How to Initially Charge the battery: 1. Connect the red positive (+) cable to the red positive (+) pole of the battery. (see figure 23) 2. Connect the black negative (-) cable to the black negative (-) pole of the battery. (see figure 24) Figure 23 Note: The red positive (+) cable has a larger diameter than the black negative (-) cable.
  • Page 13 Gas and Oil 20. Fill engine with correct amount of oil. Refer to owners manual for oil types and quantity. 21. Fill gas tank as specified in owners manual. !!WARNING!! Oil Plug. This engine may be shipped with packing oil in it.