Page 1
ATD‐80352 SABER II 7W CORDLESS UNDERHOOD LIGHT USER’S MANUAL FEATURES: • 14 Super Bright SMD LEDs • 7.4V 4000mAh Li‐Ion battery pack • Up to 3‐4 hours of continuous use • Automatic shut off and over charge protection, prolongs battery life • ABS handle with double injection, impact protection and ergonomic design provides comfortable use • Aluminum alloy hook with PVC cover for protection, soft coated padded hooks help prevent scratching of the vehicles surface • The bar extends from 47" to 70" and easily attaches to most SUV's and trucks • 360 degree ratcheting hooks provide safe and firm attachment • UL listed charger California Prop 65 WARNING: This product contains chemicals including lead, known to the State of California to cause cancer, birth defects, or other reproductive harm. Wash hands after handling.
General Safety Warnings: WARNING: The instructions and warnings contained in this manual should be read and understood before using or operating this tool. Do not allow anyone to use or operate this tool until they have read this manual and have developed a thorough understanding of how this tool works. Failure to observe any of the following instructions could result in severe personal injury to tool user and bystanders, or cause damage to the tool and property. Keep this manual for future reference. Note: The warnings and cautions discussed in this instruction manual cannot cover all possible conditions and situations that may occur. It must be understood by the operator that common sense and caution are factors which cannot be built into this product, but must be supplied by the operator. WARNING: Use safety equipment. Users and bystanders should use safety goggles or safety glasses with side shields which comply with current national standards, or when needed, a face shield. Use an ANSI approved dust mask or respirator when working around metal, wood, and chemical dusts and mists. This applies to all persons in the work area. Also use non‐skid safety shoes, hardhat, gloves, dust collection systems, and hearing protection when appropriate. WARNING: Keep bystanders and children out of the work area while operating this tool. WARNING: Always keep your work area clean, uncluttered, and well lit. Cluttered or dark areas invite accidents and injuries. DO NOT work on floor surfaces that are slippery. WARNING: Do not operate this tool if you are tired or under the influence of alcohol, drugs, or medications that could affect your ability to use the tool properly. WARNING: Dress properly. Do not wear loose clothing or jewelery as they can be caught in moving parts. Wear restrictive hair covering to contain long hair. WARNING: Do not reach over or across running machines. Keep proper footing and balance at all times. Non‐ skid footwear is recommended when working. ...
Page 3
WARNING: Care should be taken to arrange the charging cord so it will not be stepped on, tripped over, or otherwise subjected to damage or stress. WARNING: Never attempt to plug in or operate equipment with defective or damaged wires, power cord or power cord plug. Have any defective or damaged parts replaced immediately by qualified personnel. WARNING: Avoid body contact with electrically grounded surfaces. There is an increased risk of electric shock if your body is grounded. WARNING: If the work area is not equipped with a permanently installed Ground Fault Circuit Interrupter outlet (GFCI), use a plug‐in GFCI between the power tool or extension cord and the power receptacle. ATD‐80352 Specific Safety Instructions: WARNING: Read all instructions before using WARNING: For indoor use only – do not use in or around, tubs, showers, sinks, pools, hot tubs, or in a wet environment ...
Page 4
Operating Instructions: • To use, plug the unit into any 110-120 VAC power source, such as a wall receptacle. • Let the unit fully charge until the green indicator on the charger turns on before use. • Charge this light every month if not in constant use, and after each use if it is used often to insure longevity. •...
Page 5
PCBA PRT80351-08 SCREW 2.9 X16 PRT80351-19 ALUMINUM TUBE UPPER PRT80351-09 BATTERY INDICATE COVER PRT80351-20 ELASTIC BAND PRT80351-10 RIGHT HANDLE SET PRT80351-21 BLOCK PRT80351-11 ON/OFF SWITCH PRT80352-24 CHARGER Visit us at www.atdtools.com Copyright (C) 2013 ATD Tools, Inc. All rights reserved.
Need help?
Do you have a question about the ATD?80352 and is the answer not in the manual?
Questions and answers