Sony HDW-F500 Operation Manual page 94

4-4 CUE Menu
5
Repeat steps 3 and 4 to enter more characters.
Up to 80 characters can be entered.
Note
If excessive comment data are entered, the input of
cue point data may become disabled. To prevent
this, press the [F8] (TAPE INFO) button to check
the available memory.
To enter a space
Press the [F5] (SPACE) button.
If you enter a wrong character
Press the [F6] (BACK SPACE) button to go back.
Then re-enter the character.
To start the procedure over again
Press the [F9] (CANCEL) button to start again.
To change a character
Press the G button to move the cursor to the
comment to be changed. Then press the f or F
button to move the insertion position.
If the entered text is longer than the
comment box
"p or p" appears to the left or right of the box.
6
Press the [F10] (SAVE/EXIT) button.
The screen that was on before the comment data
was changed is displayed again.
Prerolling to a cue point
1
Press the [F1] (CUE SCAN) button repeatedly to
specify the direction in which the cursor moves
when the PREROLL button is pressed.
Each press of the button changes the direction as
follows: FWD (forward) n REW (reverse) n
unspecified.
FWD: Pressing the PREROLL button causes the
cursor to move to the next line, and the VTR to
preroll to the time code on that line. Invalid
time codes are ignored.
REW: Pressing the PREROLL button causes the
cursor to move to the previous line, and the
VTR to preroll to the time code on that line.
Invalid time codes are ignored.
2
Press the PREROLL button.
4-52
Chapter 4 Menu Settings
Write-protecting cue point data
Press the cursor buttons to move the cursor to the line
that is to be write-protected. Then press the [F7]
(PROTECT) button. appears between the Time and
Mrk columns to indicate that the time data, mark data,
and recording starting point setting on that line are
write-protected.
C H . C O N D
C U E
S C A N
R E C D A T E [ 1 9 9 8 / 0 2 / 1 0 ]
E N T R Y
P O I N T T I T L E [ N A G A N O J U M P L A R G E H I L L ]
N o . T i m e
0 0 0 : 0 1 : 0 2 : 0 3
C O M M N T
1 - - : - - : - - : - -
E D I T
2 0 0 : 0 3 : 0 4 : 0 3
3 0 0 : 0 4 : 0 4 : 0 3
4 0 0 : 0 5 : 0 5 : 0 3
C H A N G E
5 0 0 : 0 6 : 0 6 : 0 3
D A T A
6 - - : - - : - - : - -
D E L M A R K P R O -
P O I N T T E C T
To cancel a write-protection
Press the cursor buttons to move the cursor to the line
for which write-protection is to be cancelled. Then
press the [F7] (PROTECT) button. A message appears
(in the control panel display) requesting confirmation
of cancellation operation. Press the [F7] (PROTECT)
button while pressing down the SFT button.
T E L E F I L E
T C R 0 0 : 0 0 : 0 0 : 0 0
R e s t 5 0 %
M r k I N
N G 0 0 : 0 1 : 0 1 : 0 3
K P - - : - - : - - : - -
O K @ 0 0 : 0 3 : 0 3 : 0 3
O K 0 0 : 0 4 : 0 3 : 0 3
N G 0 0 : 0 5 : 0 4 : 0 3
O K 0 0 : 0 6 : 0 5 : 0 3
T A P E C U E N U M W R I T E /
I N F O P O I N T E X I T