Sony HDW-F500 Operation Manual page 89

To enter or modify IN/OUT point data using
the numeric buttons
1
Use the cursor buttons to move the cursor to the
IN/OUT section to be entered or modified.
To move the cursor using the numeric
buttons
With the cursor specifying Time, Mrk, IN, OUT or
the recording starting point section in the TELE
FILE menu display, enter the line number using
the numeric buttons. Then press the [F9]
(CUENUM POINT) button. The cursor will move
to the line specified by the numeric buttons.
2
Use the numeric buttons to enter the time data in
the data entry window, and then press the SET
button.
For example, to enter 00:01:30:00, press the
numeric buttons as follows: 0, 0, 1, 3, 0, 0, 0.
(There is no need to enter the first zero. When you
enter a number that is less than eight digits long,
the unspecified digits are automatically set to zero
when the SET button is pressed.
CH.COND
C U E
S C A N SET
R E C D A T E [ 1 9 9 8 / 0 2 / 1 0 ]
E N T R Y
P O I N T T I T L E [ N A G A N O J U M P L A R G E H I L L ]
N o . T i m e M r k
0 0 0 : 0 1 : 0 2 : 0 3 N G
C O M M N T
1 0 0 : 0 1 : 3 0 : 0 0 K P
E D I T
2 0 0 : 0 3 : 0 4 : 0 3 O K @
3 0 0 : 0 4 : 0 4 : 0 3 O K
4 0 0 : 0 5 : 0 5 : 0 3 N G
C H A N G E
5 0 0 : 0 6 : 0 6 : 0 3 O K
D A T A
6 - - : - - : - - : - -
D E L M A R K P R O - T A P E
P O I N T T E C T I N F O
2
1
TELE FILE
Entered time
00 01 30 00
TCR 00:00:00:00
data
R e s t 5 0 %
I N
0 0 : 0 1 : 0 1 : 0 3
- - : - - : - - : - -
0 0 : 0 3 : 0 3 : 0 3
0 0 : 0 4 : 0 3 : 0 3
0 0 : 0 5 : 0 4 : 0 3
0 0 : 0 6 : 0 5 : 0 3
C U E N U M W R I T E /
P O I N T E X I T
3
Press the IN button (to enter IN point data) or OUT
button (to enter OUT point data).
The number is entered as the time code or it
replaces the existing IN/OUT point data.
To clear the IN/OUT point data
Use the cursor buttons to move the cursor to the IN/
OUT section to be cleared, and then press the CLR
button while pressing the IN button (to clear IN point
data) or OUT button (to clear OUT point data), or
press the IN or OUT button (to clear both IN and OUT
point data) while pressing the CLR button.
To increase or decrease IN/OUT point data
one frame at a time
Use the cursor buttons to move the cursor to the IN/
OUT section to be increased or decreased, and then
press the + button (to increase the time data) or the –
button (to decrease the time data) while pressing the
IN button or the OUT button. Each time you press the
+ or – button, the time data is increased or decreased
by one frame, respectively.
To recall IN/OUT point data to the data entry
window
Use the cursor buttons to move the cursor to the IN/
OUT section to be recalled, and then press the RCL
button while pressing the IN button (to recall IN point
data) or the OUT button (to recall OUT point data).
4-47
Chapter 4 Menu Settings