About The Crossover; Display Setup; Display Setup Operation - Alpine ICS-X8 Owner's Manual

About the Crossover

Crossover (X-OVER):
This unit is equipped with an active crossover. The crossover limits the
frequencies delivered to the outputs. Each channel is controlled
independently. Thus, each speaker pair can be driven by the frequencies
for which they have been optimally designed.
The crossover adjusts the HPF (high pass filter) or LPF (low pass filter)
of each band, and also the slope (how fast the filter rolls off the highs or
lows).
Adjustments should be made according to the reproduction
characteristics of the speakers. Depending on the speakers, a passive
network may not be necessary. If you are unsure about this point, please
consult your authorized Alpine dealer.
Cut-off frequency
(1/3 octave steps)
HPF LPF
20 Hz -
Low range
----
speaker
200 Hz
Rear high
20 Hz -
----
range
200 Hz
speaker
Front high
20 Hz -
----
range
200 Hz
speaker
Low range
(Different from actual display)
Level adjusting
Output frequency range
(0 to –12 dB)
20 Hz
HPF cut-off
frequency
• HPF (high pass filter): Cuts the lower frequencies and allows the
higher frequencies to pass.
• LPF (low pass filter): Cuts the higher frequencies and allows the
lower frequencies to pass.
• Slope: The level change (in dB) for a frequency change of one octave.
• The higher the slope value, the steeper the slope becomes.
• Adjust the slope to FLAT to bypass the HP or LP filters.
• Do not use a tweeter without the HPF on or set to a low frequency, as
it may cause damage to the speaker due to the low frequency content.
• You cannot adjust the crossover frequency higher than the HPF or
lower than the LPF.
• Adjustment should be made according to the recommended crossover
frequency of the connected speakers. Determine the recommended
crossover frequency of the speakers. Adjusting to a frequency range
outside that recommended may cause damage to the speakers.
For the recommended crossover frequencies of Alpine speakers, refer
to the respective Owner's Manual.
We are not responsible for damage or malfunction of speakers caused
by using the crossover outside the recommended value.
38
-EN
Slope
HPF LPF
FLAT, –6,
---- –12, –18,
–12 dB
–24 dB/oct.
FLAT, –6,
–12, –18, ----
–12 dB
–24 dB/oct.
FLAT, –6,
–12, –18, ----
–12 dB
–24 dB/oct.
High range
Slope FLAT
Slope adjusting
(Different from actual display)
LPF cut-off
frequency

Display Setup

Display Setup Operation

The parking brake must be engaged to access the Display mode
screen. Attempting to access this screen while driving will display
the warning-Unable to operate while driving.
The following steps 1 to 6 are common operations to each
"Setting item" of Display Setup. Refer to each section for
details.
1
Touch [Setup] on the Home screen.
Level
The Setup main screen is displayed.
2
0 to
Touch [Display Setup].
The Display Setup screen appears.
• You can display the Display Setup screen from each application
0 to
screen. Touch [
mode).
3
Touch the desired application.
0 to
• "Audio" can be selected while a video is playing.
• The camera names set under the "Direct Camera" settings are
displayed. The camera names are not displayed when "Off" is
set (page 45).
• If "Nav. In" is "Off," "Navigation" will not be displayed
(page 46).
4
Touch [
Settable items differ depending on the application.
[Audio] (Video media):
Display Mode* / Live Contrast / Visual EQ / Bright / Color / Tint /
Contrast / Sharpness
[Direct Camera]:
Live Contrast / Bright / Color / Contrast
[Navigation]:
Bright / Contrast
* When media is set to AUX, the settings cannot be changed in the
situations below.
5
Touch [
6
Touch [ ] to return to the main application screen.
Touch [ ] to return to the previous screen.
• Immediately after changing the settings of Display Setup (While the
system is writing data automatically) do not turn the ignition key to
OFF. Otherwise, the settings may not be changed.
Display] on any application screen (video
] of the desired item.
] or [ ] to change its setting.