1. Manuals
  2. Brands
  3. Furuno Manuals
  4. Receiver
  5. MF/HF DSC/Watch Receiver DSC-60
  6. Installation manual

Furuno DSC-60 Installation Manual

Dsc/watch receiver
Hide thumbs Also See for DSC-60:
Table of Contents

Advertisement

Quick Links

See also: Operator's Manual
SAFETY INSTRUCTIONS .............................................................................i
SYSTEM CONFIGURATION.........................................................................ii
EQUIPMENT LISTS .....................................................................................iii
1. MOUNTING ...............................................................................................1
1.1 Main Unit............................................................................................................................ 1
1.2 Antenna (option)................................................................................................................. 3
1.3 External Loudspeaker ........................................................................................................ 5
1.4 Handset Hanger (option) .................................................................................................... 5
1.5 AC-DC Power Supply Unit (option)..................................................................................... 5
1.6 Printer PP-510 (option)....................................................................................................... 6
1.7 Distress Alert Unit IC-302-DSC/Incoming Indicator IC-303-DSC ........................................ 6
2. WIRING......................................................................................................7
2.1 Wiring................................................................................................................................. 7
2.2 Connection of AC-DC Power Supply Unit PR-300 (option) ................................................11
3. INITIAL SETTINGS .................................................................................13
3.1 System Setup................................................................................................................... 13
3.2 Setting of DIP Switches .................................................................................................... 17
3.3 Preamp Setting ............................................................................................................... 20
4. RX BOARD (OPTION) ............................................................................21
PACKING LISTS .......................................................................................A-1
OUTLINE DRAWINGS ..............................................................................D-1
SCHEMATIC DIAGRAMS ......................................................................... S-1

Installation Manual

DSC/WATCH RECEIVER
DSC-60

Advertisement

Table of Contents
loading

Related Manuals for Furuno DSC-60

Summary of Contents for Furuno DSC-60

  • Page 1: Table Of Contents

    Installation Manual DSC/WATCH RECEIVER DSC-60 SAFETY INSTRUCTIONS ................i SYSTEM CONFIGURATION.................ii EQUIPMENT LISTS ..................iii 1. MOUNTING ....................1 1.1 Main Unit..........................1 1.2 Antenna (option)......................... 3 1.3 External Loudspeaker ......................5 1.4 Handset Hanger (option) ....................5 1.5 AC-DC Power Supply Unit (option)..................5 1.6 Printer PP-510 (option).......................
  • Page 2 Y o u r L o c a l A g e n t / D e a l e r 9 - 5 2 , A s h i h a r a - c h o , N i s h i n o m i y a , J a p a n T e l e p h o n e : 0 7 9 8 - 6 5 - 2 1 1 1 T e l e f a x :...

  • Page 3: Safety Instructions

    SAFETY INSTRUCTIONS WARNING CAUTION Do not work inside the Confirm that the power supply voltage equipment unless totally is compatible with the voltage rating familiar with electrical of the equipment. circuits. Connection to the wrong power supply Hazardous voltage which can can cause fire or equipment damage.

  • Page 4: System Configuration

    SSB RADIOTELEPHONE PRINTER DISTRIBUTOR RX Board FS-75/2550 PP-510 DB-120/DB-500 FS-5000/8000 NBDP TERMINAL NAVIGATOR DP-6 DSC/WATCH TELEX DISTRESS RECEIVER ALERT BUTTON DSC-60 INCOMING IC-302-DSC INDICATOR IC-303-DSC DISTRESS MESSAGE CONTROLLER DMC-5 LOUDSPEAKER SEM-21Q HANDSET HSC701K-B20 AC/DC POWER : OPTION SUPPLY UNIT PR-300...

  • Page 5: Equipment Lists

    EQUIPMENT LISTS Standard Supply Name Type Code no. Remarks Main Unit DSC-60 Installation Materials CP05-07901 005-950-180 1 set Accessories FP05-05200 000-055-407 1 set FP05-05201, FP05-05202, Loudspeaker...

  • Page 6: Optional Equipment

    Optional Equipment Name Type Code no. Remarks OP05-91 005-950-340 05P0703 board RX Board Kit 1 set OP05-93 005-950-610 05P0703 board, w/shield cases AC-DC Power Supply PR-300 000-130-431 Unit w/installation materials (CP16- Printer PP-510 1 set 01200), accessories (FP16- 00100) Distress Message DMC-5 Controller Distress Alert Unit...

  • Page 7: Mounting

    1.1.1 General The DSC-60 can be mounted on the overhead, on a tabletop, on a bulkhead, or flush mounted in a panel. Mount the unit where it can be easily viewed and operated. When selecting a mounting location, keep in mind the following considerations, in addition to those already mentioned.
  • Page 8 1.1.3 Mounting DSC/WATCH RECEIVER DSC-60 VOLUME TEST DISTRESS 2182 IntCom SCAN ALARM PRINT CANCEL OVEN PQRS WXYZ FILE POWER CALL SETUP 5- 7.5 DSC/WATCH RECEIVER DSC-60 VOLUME TEST DISTRESS 2182 IntCom SCAN ALARM PRINT CANCEL OVEN PQRS WXYZ POWER FILE...

  • Page 9: Antenna (Option)

    The antenna commonly used for the DSC-60 is a 6 m whip antenna (local supply), long wire or optional whip of 2.6 m length with preamp unit (optional supply).
  • Page 10 Thread (14 threads/inch) 1" Pipe 2.6 m Whip Antenna Hose Mast Clamp Earth Coupling Antenna Wire Wire Antenna Fixture Preamp Unit...

  • Page 11: External Loudspeaker

    100 cm of the unit. AC-DC Power Supply Unit (option) For Convention vessels, both AC and DC power must be fed to the DSC-60, via an AC-DC power supply unit. When AC input fails, DC power is supplied. FURUNO can supply the PR-300 AC-DC power supply unit.

  • Page 12: Printer Pp-510 (Option)

    Install the unit with the two mounting fixtures (supplied). Refer to the outline drawing at the end of this manual. Connect the interconnection cable between the printer and the DSC-60. For how to load paper and set ribbon cassette, refer to the Operator’s Manual of the printer.

  • Page 13: Wiring

    2.1.1 Standard wiring All external equipment are connected to appropriate connectors on the rear panel of the DSC-60. The figure below shows the location of these connectors. Note that all interconnection cables are optionally supplied. For further details, refer to the interconnection diagram at the end of this manual.
  • Page 14 D.ANT (Distress & Safety Watch Keeping Receiver Antenna) The DSC antenna is connected to the main unit with a 50 ohm coaxial cable, type RG-8/8U or equivalent. Attach an M-type plug (if necessary) to the cable as shown below. Screw the plug into the D.
  • Page 15 External Equipment IEC61162-1 (NMEA) Connects a navigator here. The DSC-60 can receive the following sentences in IEC-61162-1 format. Use the FM14-5P connector (supplied) and interconnection cable type CO-SPEVV-SB-C 0.2x2P (option). For how to fabricate the cable, see the figure in below.
  • Page 16 PRINTER Connects the printer PP-510 (option). HANDSET Connects the HSC701K-B20 handset (option). Connects the SSB radiotelephone, by using the cable assembly 05S0784 (option). For the cable assembly UL2464-SB(M) (local supply, with no connector), fabricate the connector 17JE-23250-02 (DSC, supplied as installation materials) as below. Fold back the shield, and then wind the metallic shield tape Cable Clamp...

  • Page 17: Connection Of Ac-Dc Power Supply Unit Pr-300 (Option)

    Connection of AC-DC Power Supply Unit PR-300 (option) When connecting to an AC and DC ship’s mains, the optional AC-DC power supply unit PR-300 is required. Attach the crimp-on lug FV5.5-S4 (local supply) to the power cable (local supply) for connection with the PR-300.
  • Page 18 2.2.2 Changing the power fuse Change the power fuse according to AC input voltage as follows. AC ship’s mains Fuse 100/110 VAC 10 A 200/220 VAC Fuse for AC ship's mains AC-DC power supply unit PR-300, rear view 2.2.3 Grounding Connect a ground wire between ship’s superstructure and a fixing screw on the PR-300.

  • Page 19: Initial Settings

    SCAN FREQ AUTO ACK USER CH ERASE VOLUME MESSAGE POSITION TEST PRINT OUT SYSTEM Setup menu Select “SYSTEM” with the cursor pad. Press the [ENT] key to display the System setup menu. Enter a password referring to the FURUNO INFORMATION.
  • Page 20 Distress/safety frequency is 2187.5 kHz only (A1 and A2 area) Press the [ENT] key. 3.1.3 Line out level for DSC signal setting Set line out level. For FURUNO SSB (600 Ω), set 0 dBm. Open the System Setup menu. Press to select “LINE OUT”.
  • Page 21 Press # or $ to adjust the indicator bar (AUTO, 0.1, 0.5, 1, 2, 3, 4, 5, 10, 15). FURUNO’s SSB: Set to AUTO (Timing is controlled by the MIF command <TU>.) Other makes of SSB: Set according to specifications of equipment.
  • Page 22 Press to select the appropriate setting. OFF: Connecting with other maker’s NBDP or no NBDP. ON: FURUNO’s NBDP (ex. DP-6). Press the [ENT] key. 3.1.8 DSC signal strength CH DET S LEVEL judges whether the DSC frequency to use to send a DSC message (Routine and Business only) is in use or not.

  • Page 23: Setting Of Dip Switches

    1. Open the System setup menu. 2. Press to select “CH DET S LEVEL”. 3. Press the [ENT] key to display the CH DET S LEVEL pop-up window. S LEVEL(OFF CH DET S LEVEL pop-up window 4. Press to adjust the indicator bar. Too low a setting stops transmission of a DSC message because it detects noise on the DSC frequency.
  • Page 24 OFF at the NBDP on the system setting menu. Note 2: When the distance between the DSC-60 and radiotelephone is 5 m or more use the current loop specification. To do this, set 1/2 and 3/4 of DIP switch S4 to OFF and ON, 2 of DIP switch S5 to C.
  • Page 25 Setting for Current Loop 3.2.3 For navigator connection [IEC] NAV DATA Navigator DSC-60 (GLL,RMC,RMA,GGA,ZDA) Navigator connection Set the output data format from the navigator to IEC: RS-422 or Current Loop, and set S5 DIP switch in the main unit as below.

  • Page 26: Preamp Setting

    3.2.4 Connection to DMC-5, IC-302-DSC The above equipment can be connected at DMC port at the back of the main unit. When connecting to them, set DIP switches as below. Set to RS-422 as follows. IC-302-DSC Set to Current Loop for IC-302 connection. Preamp Setting When using the preamp for the watch receiver antenna, set J3 on the RX Board to ACTIVE.

  • Page 27: Rx Board (Option)

    4. RX BOARD (OPTION) The RX Board 05P0703 (option) enables reception of routine DSC frequencies without the SSB radiotelephone connection. For complete modification, the whip antenna for routine DSC frequency is necessary. • Necessary Parts :RX Board Kit, Type :OP05-91, Code No. :005-950-340 :RX Board Kit, Type :OP05-93, Code No.
  • Page 28 Mounting Unfasten ten binding screws to remove the upper and lower covers from the main unit. For mounting the OP05-93, remove RX Board for distress frequencies. For mounting OP05-93, set the shield case RX-1 inside the main unit as shown below. Set fixing holes in shield case RX-1 to “pegs”...
  • Page 29 Fasten the optional RX Board 05P0703 inside the main unit with six pan head screws (M3X8, supplied). For mounting OP05-93, fasten the RX Board with shield case RX-1 with six screws. Attach the coaxial cable (from the rear panel) to J1 on the RX Board. For mounting OP05-93, attach the coaxial cable to J1 through the square bush of shield case RX-2.

Table of Contents