Graco ProShot 258865 Operation Manual
  1. Manuals
  2. Brands
  3. Graco Manuals
  4. Paint Sprayer
  5. ProShot 258865
  6. Operation manual

Graco ProShot 258865 Operation Manual

Cordless paint sprayer
Hide thumbs
Table of Contents

Advertisement

Quick Links

Operation
™
ProShot
U.S. Patent No. D625,775 S; U.S. Patent No. 6,619,569; U.S. Patent No. D630,708 S;
Community Registration #001228255; India Patent No. 230058; Taiwan Patent No. D142952
China Patent No. ZL201030238948.3; and other patents pending
- For portable spray applications of water-based and oil-based
(mineral spirit-type) architectural paints and coatings only -
IMPORTANT SAFETY INSTRUCTIONS
Read all warnings and instructions in this
manual. Save these instructions.
Model 258865
Maximum Working Pressure 2000 psi (137 bar, 13.7 MPa)
Model 258859
Maximum Working Pressure 2000 psi (137 bar, 13.7 MPa)
Use only water-based or oil-based (mineral spirit-type) materials with flash point greater than 100° F
(38° C). Do not use materials which state "FLAMMABLE" on the packaging. For more information about
your material, request MSDS from distributor or retailer.
Use oil-based material outdoors or in a well-ventilated indoor area with a flow of fresh air.
Spraying certain materials may cause static build-up in the sprayer that can result in static shock to
the user. If this occurs, first ensure the material has a flash point greater than 100° F (38° C) and does not
state that it is FLAMMABLE anywhere on the package. If still feeling a static shock, the material likely con-
tains a non-mineral spirits fluid such as, but not limited to, xylene, toluene, or naphtha, which can build up
static. Switch to an alternative material.
Cordless Paint Sprayer
- Not for use in explosive atmospheres -
WARNING
WARNING
WARNING
WARNING
3A0153E
EN
ti14773a

Advertisement

Table of Contents
loading

Related Manuals for Graco ProShot 258865

Summary of Contents for Graco ProShot 258865

  • Page 1 - Not for use in explosive atmospheres - IMPORTANT SAFETY INSTRUCTIONS Read all warnings and instructions in this manual. Save these instructions. Model 258865 Maximum Working Pressure 2000 psi (137 bar, 13.7 MPa) Model 258859 Maximum Working Pressure 2000 psi (137 bar, 13.7 MPa)

  • Page 2: Table Of Contents

    (if not installed) ......11 Graco Standard Warranty ......24 Important User Information Read this before using your sprayer.

  • Page 3: Warnings

    Warnings Warnings The following warnings are for the setup, use, maintenance, and repair of this equipment. The exclamation point symbol alerts you to a general warning and the hazard symbols refer to procedure-specific risks. When these symbols appear in the body of this manual, refer back to these Warnings.
  • Page 4 Do not short-circuit the terminals of the battery. • Keep the battery away from fire. • Charge only with Graco approved charger as listed in this manual. • Do not expose to heat above 170° F (80° C). • Do not expose battery to water or rain.

  • Page 5: Component Identification

    Component Identification Component Identification ti15479a Material Cup (32 oz) ProShot Cordless Paint Sprayer Power Cord Converter (258859 only) Sprayer Hook Prime/Relief Valve Outlet Valve Repair Access Lithium Ion Premium Power Battery Charger ProShot Spray Tip/Guard Assembly (411, 515 included) Material Cup Liners (5 included) Tip Filter (*Reverse Threaded) Lithium Ion Premium Power Battery (2 included) Standard Suction Tube (sprays ceilings and walls)

  • Page 6: Common Procedures

    Common Procedures Common Procedures Pressure Relief Procedure Spray Tip Position Do not operate or spray near children. Do not aim the Always perform Pressure Relief Procedure before sprayer at, or spray any person or animal. Keep hands adjusting spray tip position. and other body parts away from the front of the sprayer.

  • Page 7: Charging The Battery

    Charging the Battery Charging the Battery To reduce the risk of electric shock, only use Graco batteries with the Graco charger. Do not insert any Batteries may leak, explode, cause burns or cause an foreign objects into the adapter cup.

  • Page 8: Setup

    Setup Setup When spraying ceilings, the inlet of the suction tube should be aimed at the back of the material cup (towards the trigger). Use only water-based or oil-based (mineral spirit-type) materials with flash point greater than 100° F (38° C). Do not use materials which state “FLAMMABLE”...

  • Page 9: Spraying Stains Or Clear Coats (Fine-Finish Optimizer)

    Setup Spraying Stains or Clear Coats 2. Put prime/relief valve to UP position, then hold trig- ger in for 10 seconds. (Fine-Finish Optimizer) The Fine-Finish Optimizer should be installed and used when spraying thin material such as stain or clear coats. The Fine-Finish Optimizer restricts the material flow ti14999a resulting in a finer quality finish.

  • Page 10: Materials

    Setup Materials 2. Use the Fine-Finish Optimizer cleaning tool to lightly push on inlet valve to make sure it moves up and down freely. Use only water-based or oil-based (mineral spirit-type) materials with flash point greater than 100° F (38° C). Do not use materials which state “FLAMMABLE”...

  • Page 11: Install Tip/Guard Assembly

    Install Tip/Guard Assembly (if not installed) Install Tip/Guard Assembly Getting Started with Basic (if not installed) Techniques Reversible Tip Selection Chart Use a piece of scrap cardboard to practice these basic spraying techniques before you begin spraying the surface. MATERIALS •...

  • Page 12: Unclogging Spray Tip/Guard Assembly

    Unclogging Spray Tip/Guard Assembly Unclogging Spray 5. Disengage trigger lock, put prime/relief valve DOWN to spray position, and resume spraying. Tip/Guard Assembly ti14995a ti15425a Do not operate or spray near children. Do not aim the sprayer at, or spray any person or animal. Keep hands 6.

  • Page 13: Shutdown And Cleaning

    Shutdown and Cleaning Shutdown and Cleaning 2. Remove material cup and properly dispose cup liner or excess material. NOTICE Failure to properly clean sprayer after each use will result in hardened materials, damage to the sprayer, and the warranty will no longer be valid. Flushing Sprayer ti15000a 3.
  • Page 14 Shutdown and Cleaning 6. Disconnect trigger lock and trigger sprayer for 10. Engage trigger lock and put prime/relief valve UP to approximately 15 seconds. Engage trigger lock. release pressure. ti14994a ti14994a 11. Remove material cup and discard used fluid. 7. Discard contaminated fluid and refill with appropri- 12.

  • Page 15: Cleaning Sprayer Exterior

    Storage Cleaning Sprayer Exterior 3. Reverse spray tip to UNCLOG position, put prime/relief valve DOWN to spray position, and aim sprayer into waste area. Pull trigger for 1-2 seconds. • Wipe paint off outside of sprayer using a soft cloth moistened with water or flushing fluid.

  • Page 16: Replacement Parts And Kits

    Replacement Parts and Kits Replacement Parts and Kits ti16473c ti15497a Ref. Part Description Ref. Part Description 16E403 Sprayer Cup Seal 262367 Sprayer, replacement (no tip, battery, suction 24D425 Cover with seal (included in 16 and 17) tube, or material cup) 13a 16C650 Material Cup Cover Seal (included in 16 and 17) 16D562...

  • Page 17: Proshot Repair Kit

    ProShot Repair Kit ProShot Repair Kit 4. Use tool (supplied) to loosen and remove outlet valve fitting. Outlet Valve Fitting NOTE: Before doing any repair to pump, perform ti15506a Flushing Sprayer procedure, page 13. Removal Installation 1. Engage trigger lock and pull relief valve UP to release pressure.

  • Page 18: Alternate Priming Method

    Alternate Priming Method Alternate Priming Method 4. Hold sprayer above sink or waste area, disengage the trigger lock, and quickly trigger sprayer until material comes out of the drain tube. 1. Engage trigger lock and put prime/relief valve UP to release pressure.

  • Page 19: Inlet Valve Cleaning

    Alternate Priming Method Inlet Valve Cleaning Removal Installation NOTE: Before installing, make sure o-ring (c) is installed 1. Engage trigger lock and pull relief valve UP to on inlet valve (b). release pressure. 1. Place inlet valve (b) with spring (a) on top of inlet fit- ting (d).

  • Page 20: Troubleshooting

    Troubleshooting Troubleshooting Check everything in this Troubleshooting Table before you bring the sprayer to an authorized service center. Problem Cause Solution ProShot makes no sound when Trigger is locked. Disengage trigger lock. See page 6. trigger is pulled Status Indicator Light is solid RED Replace with charged battery and place old bat- when triggering, indicating that the tery in charger or allow battery to warm up.
  • Page 21 Troubleshooting Problem Cause Solution ProShot sprays with poor Tip is partially clogged See Unclogging Tip/Guard Assembly, page results Tip is not in correct position Rotate tip to SPRAY position. Incorrect tip for application of See Reversible Tip Selection Chart, page 11. material.
  • Page 22 Troubleshooting Problem Cause Solution Spray pattern is too narrow: Sprayer is too close to target surface. Move sprayer away from surface (10 in). Incorrect tip for application of material. See Reversible Tip Selection Chart, page Tip is worn or damaged. Replace tip.

  • Page 23: Technical Data

    Technical Data Technical Data 258865 258859 Sprayer: Maximum working pressure 2000 psi (137.8 bar, 13.7 MPa) Weight 6.32 lb (2.87 kg) Dimensions: Length 13.25 in. (33.6 cm) Width 5.0 in. (12.7 cm) Height 10.375 in. (26.4 cm) Storage temperature range ◆❖...

  • Page 24: Graco Standard Warranty

    With the exception of any special, extended, or limited warranty published by Graco, Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment determined by Graco to be defective.

This manual is also suitable for:

Proshot 258859

Table of Contents