Basic Operation; Level; Cross Fader Assign - Pioneer DJM-2000NXS Operating Instructions Manual

Pioneer djm-2000nxs dj mixer operating instructions
Hide thumbs Also See for DJM-2000NXS:
Table of Contents

Advertisement

Available languages

Available languages

r ON/OFF button (page 19)
s LIVE SAMPLER (UTILITY, WAKE UP) buttons (page 18,
page 28)
t SYNC MASTER/MIDI button (page 20)
u MIX button (page 16)
v REMIX button (page 17)
w ON/OFF button (TOUCH PANEL EFFECT) (page 16)
x Crossfader (page 13)
y MASTER control (page 13)
z Master Level Indicator (page 13)
A BALANCE control (page 15)
B MONO, STEREO selector switch (page 15)
C BOOTH MONITOR control (page 15)
D START/STOP (SNAPSHOT) button (page 20)
E ON/OFF (MIDI) button (page 20)
F CH EQ (ISOLATOR, EQ) selector switch (page 13)
G CH FADER ( ,
) selector switch (page 14)
H CROSS FADER ( ,
,
Do not pull on the channel fader and crossfader knobs with excessive
force. The knobs have a structure by which they cannot be pulled off
easily. Pulling the knobs strongly may result in damaging the unit.
) selector switch (page 14)

Basic Operation

Outputting sound
1 Press [POWER] button.
Turn on the power of this unit.
2 Switching the [CD/DIGITAL, PHONO, LINE, USB */*]
switch
Selects the input sources for the different channels from among the
devices connected to this unit.
— [CD/DIGITAL]: Selects the DJ player connected to the [CD] termi-
nals. To select the DJ player connected to the [DIGITAL IN] termi-
nal, set the [CD, DIGITAL] switch on the rear panel to [DIGITAL].
— [PHONO]: Selects the analog player connected to the [PHONO]
terminals.
— [LINE]: Selects the cassette deck or CD player connected to the
[LINE] terminals.
— [USB */*]: Selects the sound of the computer connected to the
[USB] port.
3 Turn the [TRIM] control.
Adjusts the level of audio signals input in each channel.
The corresponding channel level indicator lights when audio signals are
being properly input to that channel.
4 Move the channel fader away from you.
Adjusts the level of audio signals output in each channel.
5 Switch the [CROSS FADER ASSIGN (A, THRU, B)]
switch.
Switches the output destination of each channel.
— [A]: Assigns to [A] (left) of the crossfader.
— [B]: Assigns to [B] (right) of the crossfader.
— [THRU]: Selects this when you do not want to use the crossfader.
(The signals do not pass through the crossfader.)
6 Set the crossfader.
This operation is not necessary when the [CROSS FADER ASSIGN (A,
THRU, B)] selector switch is set to [THRU].
7 Turn the [MASTER] control.
Audio signals are output from the [MASTER1] and [MASTER2]
terminals.
The master level indicator lights.
Adjusting the sound quality
Turn the [EQ/ISO (HI, MID, LOW)] controls for the
respective channels.
Refer to Specifications on page 32 for the range of sound that can be
adjusted by each control.
 Switching the function of the [EQ/ISO (HI, MID,
LOW)] controls
Switch the [CH EQ (ISOLATOR, EQ)] selector switch.
— [ISOLATOR]: The isolator function is set. The indicator lights.
— [EQ]: The equalizer function is set.
13
En

Advertisement

Table of Contents
loading

This manual is also suitable for:

Djm-2000nexus

Table of Contents