Specific Safety Rules - Makita HM1202C Instruction Manual

Hide thumbs Also See for HM1202C:
Table of Contents

Advertisement

Available languages

Available languages

17. Do not use tool if switch does not turn it on or
off. Any tool that cannot be controlled with the
switch is dangerous and must be repaired.
18. Disconnect the plug from the power source
before making any adjustments, changing
accessories,
preventive safety measures reduce the risk of
starting the tool accidentally.
19. Store idle tools out of reach of children and
other untrained persons. Tools are dangerous in
the hands of untrained users.
20. Maintain tools with care. Keep cutting tools
sharp and clean. Properly maintained tools with
sharp cutting edges are less likely to bind and are
easier to control.
21. Check for misalignment or binding of moving
parts, breakage of parts, and any other
condition that may affect the tool's operation.
If damaged, have the tool serviced before
using. Many accidents are caused by poorly
maintained tools.
22. Use only accessories that are recommended
by
the
manufacturer
Ampere Rating
More Than
0
6
10
12
000173

SPECIFIC SAFETY RULES

DO NOT let comfort or familiarity with product
(gained from repeated use) replace strict adherence
to hammer safety rules. If you use this tool unsafely
or incorrectly, you can suffer serious personal
injury.
1.
Hold tool by insulated gripping surfaces when
performing an operation where the cutting tool
may contact hidden wiring or its own cord.
Contact with a "live" wire will make exposed metal
parts of the tool "live" and shock the operator.
2.
Wear ear protectors when using the tool for
extended periods. Prolonged exposure to high
intensity noise can cause hearing loss.
3.
Wear a hard hat (safety helmet), safety glasses
and/or face shield. Ordinary eye or sun
glasses are NOT safety glasses. It is also
highly recommended that you wear a dust
or
storing
the
tool.
for
your
Table 1: Minimum gage for cord
Not More Than
6
10
12
16
Accessories that may be suitable for one tool, may
become hazardous when used on another tool.
Service
23. Tool service must be performed only by
qualified
Such
maintenance performed by unqualified personnel
could result in a risk of injury.
24. When servicing a tool, use only identical
replacement parts. Follow instructions in the
Maintenance section of this manual. Use of
unauthorized parts or failure to follow Maintenance
instructions may create a risk of electric shock or
injury.
USE PROPER EXTENSION CORD. Make sure your
extension cord is in good condition. When using an
extension cord, be sure to use one heavy enough to
carry the current your product will draw. An
undersized cord will cause a drop in line voltage
resulting in loss of power and overheating. Table 1
shows the correct size to use depending on cord
length and nameplate ampere rating. If in doubt, use
the next heavier gage. The smaller the gage number,
model.
the heavier the cord.
Volts
120 V
25 ft.
18
18
16
14
USB009-2
mask and thickly padded gloves.
4.
Be sure the bit is secured in place before
operation.
5.
Under normal operation, the tool is designed
to produce vibration. The screws can come
loose easily, causing a breakdown or accident.
Check tightness of screws carefully before
operation.
6.
In cold weather or when the tool has not been
used for a long time, let the tool warm up for a
while by operating it under no load. This will
loosen up the lubrication. Without proper
warm-up, hammering operation is difficult.
7.
Always be sure you have a firm footing.
Be sure no one is below when using the tool in
high locations.
8.
Hold the tool firmly with both hands.
9.
Keep hands away from moving parts.
10. Do not leave the tool running. Operate the tool
only when hand-held.
3
repair
personnel.
Total length of cord in feet
50 ft.
100 ft.
AWG
16
16
16
14
16
14
12
Not Recommended
Service
or
150 ft.
14
12
12

Advertisement

Table of Contents
loading

Subscribe to Our Youtube Channel

This manual is also suitable for:

Hm1202

Table of Contents