Summary of Contents for Star Micronics TSP600 Series
Page 1
THERMAL PRINTER TSP600 Series TECHNICAL MANUAL [ FIRST EDITION ]...
Page 2
NOTICE • All rights reserved. Reproduction of any part of this manual in any form whatsoever, without STAR’s express permission is forbid- den. • The contents of this manual are subject to change without notice. • All efforts have been made to ensure the accuracy of the contents of this manual at the time of going to press.
Page 3
INTRODUCTION This manual describes the thermal printer TSP600 series. It is designed for use as a reference for periodic inspections and maintenance procedures to be executed by service personnel. It is not intended for the general user. Users of this manual should have a basic knowledge and understanding of the English language.
CHAPTER 1 PARTS REPLACEMENT This chapter explains disassembly and reassembly of the printer. Note the following precautions during disassembly and reassembly. Disconnect the printer power cord plug from the wall outlet before servicing it. Assembly is the reverse of disassembly unless otherwise specified. After reassembly, coat the screw heads with locking sealant.
PARTS REPLACEMENT Rear Cover Unit Turn off the power switch 1, disconnect the power cord from the wall outlet. Push the cover open lever 2 and open rear cover unit 3. Allowing about 5mm of uniform slackening at points A (left/right) of the rear cover unit 3, along the arrow direction, remove it from case unit.
PARTS REPLACEMENT Board Chassis Unit Turn off the power switch1, disconnect the power cord from the wall outlet. Remove • Case unit according to the procedure described in item 2. • Three screws 2 • Five connectors 3 • Mechanism chassis unit 4 •...
PARTS REPLACEMENT Printer Mechanism Turn off the power switch, disconnect the power cord from the wall outlet. Remove • Mechanism shassis unit according to the procedure described in item 3. • Three screws 1 • Paper stocker 2 • Screw 3 •...
Page 11
CHAPTER 2 MAINTENANCE AND LUBRICATION Maintenance......................1-1. Cleaning ........................9 1-2. Checks ........................9 Lubrication ......................10 2-1. Type of oil ......................10 2-2. Lubrication method ....................10 2-3. Lubrication locations ................... 10...
MAINTENANCE AND LUBRICATION Maintenance Carry out maintenance control items listed below to maintain the original performance of this printer and prevent trouble from occurring. 1-1. Cleaning Removal of dirt. Clean the dirt with tissure or soft cloth. Note: Do not use thinners or trichlene/ketone base solvents for cleaning as they can damage plastic parts. Be careful not to damage electrical parts, wired areas or mechanisms and avoid getting them wet.
Page 14
MAINTENANCE AND LUBRICATION Lubrication Lubrication is extremely important for preserving the original performance of the printer over a long period of time. 2-1. Type of oil The type of oil used has a major influence on the performance and durability of the printer.You should pay particular attention to the cold temperature properties of the oil.
CHAPTER 3 PARTS LIST HOW TO USE PARTS LIST DRWG. NO. This column shows the drawing number of the illustration. REVISED EDITION MARK This column shows a revision number. PART NO. Parts numbers must be notified when ordering replacement parts. Parts described as “NPN” have no parts number and are not in stock, i.e., unavailable.
3-1-2. Parts List Printer Assembly DRWG.NO. REV. PARTS NO. PARTS NAME Q'TY REMARKS RANK BOARD CHASSIS TSP6 30991230 RUBBER FOOT 12X12 TSP7 37477000 MAIN LOGIC BOARD UNIT TSP6 37470000 CASE UNIT TSP6 WHITE 37470010 CASE UNIT TSP6GRY GRAY 33400080 COVER OPEN LEVER TSP6 WHITE 33400100 COVER OPEN LEVER...
3-2-2. Parts List Printer Mechanism DRWG.NO. REV. PARTS NO. PARTS NAME Q'TY REMARKS RANK 37489000 HEAD UNIT TMP6 37487000 PE SWITCH UNIT TMP6 37482100 CUTTER UNIT TMP6 AUTO CUTTER ONLY 37482000 MOTOR UNIT TMP6 FRAME UNIT TMP6 33102270 GEAR 33X40X0.4 TMP6 33102280 GEAR 22X37X0.4 TMP6...
3-5-2. Parts List Main Logic Board DRWG.NO. REV. PARTS NO. PARTS NAME Q'TY REMARKS RANK BC01-03 CERA.CAPA.CHIP1608 0.022UF 50V BC04-06 CERA.CAPA.CHIP1608 0.1UF 25V BC07 NOT MOUNTED BC08A CERA.CAPA.CHIP1608 0.022UF 50V BC08B CHEM. CAPA. 47UF BC09 CHEM. CAPA. 47UF BC10 NOT MOUNTED BC12-13 NOT MOUNTED CERA.CAPA.CHIP1608 0.22UF 10V...
Page 30
Main Logic Board DRWG.NO. REV. PARTS NO. PARTS NAME Q'TY REMARKS RANK IC11 IC-REG SI-8401L IC12-13 NOT MOUNTED JP1A NOT MOUNTED JP1B CHIP RESISTOR 0 OHM 1/16W JUMPER WIRE 1/6W-L3.2 LED1 LED CHIP LT1E40A* LED2 LED GL3KG8 LED3 LED GL3PR8 LED2-3 LED SPACER LH-3-8 R101...
3-9-2. Parts List Parallel Interface Board DRWG.NO. REV. PARTS NO. PARTS NAME Q'TY REMARKS RANK BC1-3 CERA.CAPA.CHIP1608 0.022UF 50V NOT MOUNTED CERA.CAPA.CHIP1608 1000PF 50V C3-4 NOT MOUNTED CHEM. CAPA. CONNECTOR PHEC40P-R111 CONNECTOR 57RE40360-730BD29 08211030 TTL IC HD74LS374FP*EL TTL IC 74ALS32FP*EL 08210126 TTL IC 74LS05FP*EL L1-2 CHIP RESISTOR...
Page 40
ELECTRONIC PRODUCTS DIVISION OVERSEAS SUBSIDIARY COMPANIES STAR MICRONICS U.K. LTD. STAR MICRONICS CO., LTD. STAR MICRONICS AMERICA, INC. Star House, Peregrine Business 536 Nanatsushinya, 1150 King Georges Post Road, Edison, Park, Gomm Road, High Wycombe, Shimizu, Shizuoka, 424-0066 Japan NJ 08837-3729 U.S.A.