Seamless Loop/Hot Start/Stutter And Splice - Denon DN-D9000 Operating Instructions Manual

ENGLISH

SEAMLESS LOOP/HOT START/STUTTER AND SPLICE

9
q, w, y
RVS
FLIP
t, y CLR
FLIP
CLR
Operation display
(refer to the section
describing the display)
CONT./SINGLE
Seamless Loop/Hot Start/Stutter (A1, A2 buttons)
Setting the A point (loading the Hot Start
data)
q Push the A1 or A2 button to
set the A point and Hot Start
data loading starts.
• A1 and A2 buttons can be used
1
separately for each Hot Start.
• When an A point is set, the
corresponding A button and FLIP LED
light and that button is set to the Hot
Start mode.
• The BPM is set independently for each
hot start.
Starts Hot Start
w When A1 or A2 button is
2
pushed, Hot Start playback
starts from the corresponding
A point.
Setting the B point for Seamless Loop
e When the B button is pushed
after setting the A point or
after starting Hot start
playback, the B point is set
3
-1
and Seamless Loop playback
starts from the A point.
• The B button works with respect to the
A point operated before the B button
was pushed.
14
e r
-TRACK HOT START -TRACK PLAY
SAMPLER
PARAMETERS TRACK
SAMP1 SAMP2 B EXIT/RELOOP
STOP
PUSH
ON/OFF
EXIT/
A 3 A 4 B CUE
RELOOP
A3 A4 CUE
A 3/4 A/B TRIM
PITCH/KEY
EXIT/
A 1 A 2 B
RELOOP
A1 A2 4 HOT START PITCH/VOL SPLICE
RANGE
A3 B A4 B
A1 B A2 B
TOTAL REMAIN ELAPSED CONT. SINGLE KEY ADJ. DRAG S.
m s
BRAKE
m s f
ECHO
MEMO DUMP
PROG RVS
TIME MEMO PROGRAM PLATTER MODE
RELAY TOTAL TIME PRESET RANDOM ALL OFF
CUE
TAP
STUTTER PLAY/PAUSE AUTO
• If the B button is pushed during
seamless loop playback or after EXIT
playback, the B point moves to the
3
-2
point at which the button was pushed.
A 1
• When the B point is set, the B and
LOOP LEDs light.
Playing seamless loops
• When the B point for A1 is detected after
playback started from A1 point, playback
returns to A1 point with seamless. While
4
A1 to B looping, B point for A2 ignored.
• When the B point for A2 is detected after
playback started from A2 point, playback
returns to A2 point with seamless. While
A2 to B looping, B point for A1 ignored.
A 1
Exit/Reloop
r In Seamless Loop playback,
you can force exit from or
return in the loop.
EXIT:
While the Seamless Loop playback, push
the EXIT/RELOOP button to exit from
B 5
loop. DN-D9000 continues playback after
the B point.
RELOOP:
When the EXIT/RELOOP button is pushed
after exit the loop, Seamless Loop
playback resumes from the A point.
Stutter
• A1 and A2 points can be also used for
Stutter playback.
t To enable stutter playback,
6
-TRACK HOT START push FLIP button for A1/A2
RVS SAMP1 SA
buttons, then FLIP LED turns
OPEN/
FLIP A 3 A
CLOSE
off.
CLR A3 A4 CUE
PITCH BEND
Press the FLIP button to switch between
FLIP A 1 A
CLR A1 A2 the Hot Start/Seamless Loop and Stutter
modes.
A3 B
A1 B
TOTAL REMAIN ELAPSE
m
m s
Clear the A1/A2 point
MEMO
PROG
0% y While pressing the FLIP/(CLR) button, push
CONT./SINGLE TIME M
the A1 or A2 button to clear the
RELAY TOTAL TIME PR
corresponding A and B points.
CUE
Or push the Flip button for more than 1 sec
7
STUTTER
to clear both A1 and A2 points at once.
REMOTE CONTROLLER RC-D90
FLIP
EXIT/
RELOOP
FLIP
A 1