Residual Risks; Electrical Safety - Black & Decker DV4800N Original Instructions Manual

Never attempt to charge nonrechargeable batteries.
u
If the supply cord is damaged, it must be replaced by the
u
manufacturer or an authorised Black & Decker Service
Centre in order to avoid a hazard.
Do not expose the charger to water.
u
Do not open the charger.
u
Do not probe the charger.
u
The appliance/tool/battery must be placed in a well venti-
u
lated area when charging.
Safety of others
This appliance is not intended for use by persons (includ-
u
ing children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction concern-
ing the use of the appliance by a person responsible for
their safety.
Children should be supervised to ensure that they do not
u
play with the appliance.

Residual risks.

Additional residual risks may arise when using the tool which
may not be included in the enclosed safety warnings. These
risks can arise from misuse, prolonged use etc.
Even with the application of the relevant safety regulations
and the implementation of safety devices, certain residual
risks can not be avoided. These include:
Injuries caused by touching any rotating/moving
u
parts.
Injuries caused when changing any parts, blades or
u
accessories.
Injuries caused by prolonged use of a tool. When
u
using any tool for prolonged periods ensure you take
regular breaks.
Impairment of hearing.
u
Health hazards caused by breathing dust developed
u
when using your tool (example:- working with wood,
especially oak, beech and MDF.)

Electrical safety

Your charger has been designed for a specific voltage. Always
check that the mains voltage corresponds to the voltage on
the rating plate. Never attempt to replace the charger unit with
a regular mains plug.
Symbols on the charger
Read all of this manual carefully before using the
# appliance.
This tool is double insulated; therefore no earth wire
is required. Always check that the power supply
corresponds to the voltage on the rating plate.
(Original instructions)
w
Short circuit proof safety isolating transformer. The
mains supply is electrically separated from the
x
transformer output.
The charger automatically shuts off if the ambient
temperature becomes too high. As a consequence
the charger will be inoperable. The charging base
must be disconnected from the mains supply and
$
taken to an authorised service centre for repair.
The charging base is intended for indoor use only.
Features
This tool includes some or all of the following features.
1. On/off switch
2. Bowl release button
3. Charging indicator
4. Charging socket (DV4800N, DV9610PN and
WD9610ECN Only)
5. Dust bowl
6. Charger
7. Charging base (WD4810N, WD7210N and WD9610N
Only)
Fig. A
8. Dry pick up cloth filter (DV4800N, DV9610PN Only)
9. Pre-filter (DV9610N Only)
10. Wet/Dry foam insert (WD4810N, WD7210N, WD9610ECN
and WD9610N Only)
11. Wet/Dry deflector (WD4810N, WD7210N, WD9610ECN
and WD9610N Only)
Fig. B
12. Squeegee (WD4810N, WD7210N, WD9610ECN and
WD9610N Only)
13. Powered brush head (DV9610PN Only)
Installation
Wall Mounting (fig. C) (DV9610PN and WD9610ECN
Only)
The product can be attached to a wall to provide a convenient
storage and charging point for the appliance.
When fixing to a wall, make sure that the fixing method is
suitable for the wall type and is appropriate to the weight of
the appliance.
Mark the location of the screw holes (within reach of an
u
electrical outlet for chargeing the vac while it is on the wall
bracket).
Insert the charger cord into the curved slot in the wall
u
mount bracket leaving approximately 8-9 inches excess.
ENGLISH
5