Technical Specifications - Lab.gruppen FP+ Series Operation Manual

9 TEChNICAL sPECIFICATIONs

Following are the FP+ Series technical specifications. These figures are accurate at the time of printing but
please note that all figures are subject to change without notice. For the most accurate and current information
available, please visit www.labgruppen.com.
Model
Number of channels
Peak total output all channels driven
Peak output voltage per channel
Max. output current per channel
Max. Output Power
16 ohms per ch. (all ch.'s driven)
8 ohms per ch. (all ch.'s driven)
4 ohms per ch. (all ch.'s driven)
2 ohms per ch. (all ch.'s driven)
16 ohms Bridged per ch.
8 ohms Bridged per ch.
4 ohms Bridged per ch.
2 ohms Bridged per ch.
Performance with Gain
THD 20 Hz - 20 kHz for 1 W
THD at 1 kHz and 1 dB below clipping
Signal To Noise Ratio
Channel separation (Crosstalk) at 1 kHz
Frequency response (1 W into 8 ohms) +0/-3 dB
Input Impedance
Input Common Mode Rejection, CMR
Output impedance @ 100 Hz
Output slew rate into 8 ohms
Voltage Peak Limiter (VPL), max. peak output
VPL, selectable per ch. (V)
VPL, selectable when bridged (V)
Voltage Peak Limiter mode (per ch.)
Gain and Level
Amplifi er gain selectable (all channels)
– rear-panel switches
Default gain
Level adjustment (per ch.)
Connectors and switches
Input connectors (per ch.)
Output connectors (per ch.)
Output bridge mode per two ch.'s
NomadLink ® network
Intelligent fans (on/off)
Power on/off and Remote enable on/off
Cooling
front-panel indicators
Common
Per channel
Power
Operating voltage, 230 V / 115 V nominal
Minimum power-up voltage, 230 V / 115 V
Power Average Limiter (PAL)
Soft start / Inrush Current Draw
Mains connector
dimensions (W/h/d)
Weight
finish
Approvals
Note 1): Automatic -6 dB gain compensation when bridging channels.
Note 2): PAL can reduce the maximum output power to keep the power supply operating safely, and/or to prevent excessive current draw tripping the mains breaker.
Refer to Operation Manual.
Note 3): The amplifier will be fully operational at bridge-mode 2 ohm loads, but due to physical constraints in the construction, the max. output power will not be
significantly higher than running individual channels and therefore not stated here.
Note 4): Separate 230 V or 115 V versions available. Not selectable on the amplifier.
All specifications are subject to change without notice.
32 FP+ Series Operation Manual
fP 13000
2
13000 W
195 V
58 Arms
1200 W
2350 W
4400 W
6500 W
4700 W
8800 W
13000 W
3)
35 dB and VPL: 195 V
0.1%
0.05%
112 dBA
70 dB
6.8 Hz - 34 kHz
20 kOhm
54 dB
19 mOhm
20 V/microsecond
195, 170, 140, 116, 100,
80, 66, 54 V
390, 340, 280, 232,
1)
200, 160, 132, 108 V
Hard / Soft
1)
23, 26, 29, 32, 35, 38, 41, 44 dB
38 dB
Front-panel potentiometer, 21 position detented from -inf to 0 dB
3-pin XLR, electronically balanced
Neutrik Speakon or Binding Posts (must be specified upon order). BP only on FP 13000
A+B - Ch. A is signal input source. A+B, C+D - Ch.'s A and C are input source
2 x RJ45 Ethercon connectors, IN and OUT
Yes, depending on presence of output signal
Individual switches on front-panel
Two fans, front-to-rear airfl ow, temperature controlled speed
NomadLink
Signal present / High-impedance; -20 dB, -15 dB, -10 dB and -4 dB output
signal; Voltage Peak Limiter (VPL); Current Peak Limiter (CPL):
Very High Frequency (VHF); High temperature; Fault; Mute
4) 130-265 V / 65-135 V
171 V / 85 V
Yes
2)
Yes / max. 5 A
230 V CE: 16 A, CEE7; 115 V ETL: 30 A Twist lock
W: 483 mm (19"), H: 88 mm (2 U), Overall D: 396 mm (15.6"), Mounting D: 358 mm (14.1")
12 kg (26.4 lbs.)
Black painted steel chassis with black painted steel / aluminum front
CE, ANSI/UL 60065 (ETL), CSA C22.2 NO. 60065, FCC
fP 7000
2
7000 W
155 V
42 Arms
730 W
1450 W
2800 W
3500 W
2900 W
5600 W
7000 W
3)
35 dB and VPL: 155 V
0.1%
0.05%
112 dBA
70 dB
6.8 Hz - 34 kHz
20 kOhm
50 dB
19 mOhm
20 V/microsecond
155, 121, 101, 83, 70,
56, 47, 38 V
310, 242, 202, 166,
140, 112, 94, 76 V
38 dB
Network; Power Average Limiter (PAL)
® 2)
fP 10000q fP 6000q
4 4
10000 W 6000 W
150 V 101 V
38 Arms 27 Arms
660 W 320 W
1300 W 625 W
2100 W 1250 W
2500 W 1500 W
2600 W 1250 W
4200 W 2500 W
5000 W 3000 W
3) 3)
35 dB and VPL: 150 V 35 dB and VPL: 101 V
0.1% 0.1%
0.05% 0.05%
112 dBA 112 dBA
70 dB 70 dB
6.8 Hz - 34 kHz 6.8 Hz - 34 kHz
20 kOhm 20 kOhm
45 dB 50 dB
56 mOhm 56 mOhm
20 V/microsecond 20 V/microsecond
150, 121, 101, 83, 70, 101, 83, 70, 56, 47,
56, 47, 38 V 38 V
300, 242, 202, 166, 202, 166, 140, 112,
140, 112, 94, 76 V 94, 76 V
35 dB 35 dB
; Power on