Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Worx WX420
Summary of Contents for Worx WX420
- Page 1 SAFETY AND OPERATING MANUAL Mini-circular saw WX420...
-
Page 2: General Power Tool Safety Warnings
Damaged or entangled connection of dust extraction and cords increase the risk of electric shock. collection facilities, ensure these are e) When operating a power tool connected and properly used. Use outdoors, use an extension cord Mini-circular saw WX420... -
Page 3: Safety Instructions For All Saws
The blade washers and could result in a hazardous situation. bolt were specially designed for your saw, for optimum performance and safety of 5 SERVICE operation. a) Have your power tool serviced by a qualified repair person using only Mini-circular saw WX420... -
Page 4: Safety Instructions
An unprotected, d) Support large panels to minimise the coasting blade will cause the saw to walk risk of blade pinching and kickback. backwards, cutting whatever is in its path. Large panels tend to sag under their own Mini-circular saw WX420... -
Page 5: General Safety
Bright shiny reflective sheet steel or similar is not suitable for laser applications as the reflective surface may direct the laser beam back at the operator. e) Do not change the laser device with a different type. The manufacturer or an Mini-circular saw WX420... - Page 6 SyMBolS To reduce the risk of injury, user must read instruction manual. Warning Double insulation Wear eye protection Wear ear protection Wear dust mask Laser radiation Do not stare into beam RCM marking Mini-circular saw WX420...
- Page 7 Mini-circular saw WX420...
- Page 8 18. BLADE CLAMPING WASHER (See Fig. C) 19. PARALLEL GUIDE (See Fig. D) 20. VACUUM ADAPTER (See Fig. E) 21. PLASTIC BASE PLATE COVER (See Fig. F1) 22. LASER BATTERIES (TWO) (See Fig. j3) 23. DEPTH OF CUT INDICATOR Mini-circular saw WX420...
-
Page 9: Technical Data
We recommend that you purchase your accessories from the same store that sold you the tool. Use good quality accessories with a well-known brand name. Choose the type according to the work you intend to undertake. Refer to the accessory packaging for further details. Store personnel can assist you and offer advice. Mini-circular saw WX420... -
Page 10: Intended Use
NOTE: The steps involved in changing the blade are the same as the steps used when installing the blade. NOTE: Remove both spanners after the saw blade is tightly attached. WARNING: When mounting, ensure that the cutting direction of the teeth (direction of arrow Mini-circular saw WX420... - Page 11 (sold separately). The use of the vacuum is strongly recommended as it keeps the work area clean, dramatically increases cut visibility and reduces airborne dust. It also keeps dust out of the working elements of the guard. Mini-circular saw WX420...
-
Page 12: Operation
Lock down the depth of cut adjustment and lock lever (8). (See Fig. H2) When plunge or pocket cutting into the middle (or interior) of the work piece, through the narrow slot, you can easily see the cutting mark you draw and the Mini-circular saw WX420... -
Page 13: Using The Laser
The blade alignment indicator (12) in the front of the 17 18 base plate is used as a cutting guide. Always guide it along the cutting mark made on the workpiece for accurate cutting. NOTE: It is best to carry out a trial cut. Mini-circular saw WX420... - Page 14 Ensure the blade is not touching but is close to the work surface. Hold the saw firmly while applying the least amount of pressure as possible on base plate. To avoid kickback, you should hold the tool Mini-circular saw WX420...
-
Page 15: Working Hints For Your Tool
Always store your power tool in a dry place. Keep the motor ventilation slots clean. Keep all working controls free of dust. If the supply cord is damaged, it must be replaced by Mini-circular saw WX420... - Page 16 Periodically clear dust and chips from guard and base to ensure proper performance. Mini-circular saw WX420...
-
Page 17: Troubleshooting
Saw is not being guided mounted. properly. Use an edge guide. Blade kicks back when Blade is not spinning fast Allow the saw blade to reach full beginning a cut.. enough speed prior to beginning a cut. Mini-circular saw WX420... - Page 20 Copyright © 2013, Positec. All Rights Reserved. 2PSC15APK11001A1...