Related Manuals for Giada MI-D2700D
Summary of Contents for Giada MI-D2700D
- Page 1 Motherboard User’s Manual www.giadatech.com MI-D2700D/N2600D Version 001 All right reserved...
-
Page 2: Table Of Contents
www.giadatech.com Contents Gratitude …………………………………………………………………………… 4.12 Power ATX20 Pin …………………………………………………… 4.13 F_ PANEL …………………………………………………………… About the product ………………………………………………… …………… 5. Rear panel interface ……………………………………………………… 1. Picture of the motherboard ……………………………………………… 2. Features …………………………………………………………………… BIOS setting ………………………… …………… ………………………… I II 2.1 Processor ……………………………………………………………… 1. -
Page 3: Gratitude
LVDS display（Max 1440*900) Any question about the product, please send e-mail to our support center. Headquarter: Sales@giadatech.com support@giadatech.com USA office: support@giadapc.co D2700D N2600D NOTE: This is Giada real product photo show for your reference only, Product appearance depends on goods. -
Page 4: Features
www.giadatech.com II. Hardware installation 2. Features 2.5 Power management · Support APM and ACPI; 2.1 Processor · Compatible with energy star “Green PC”. · ® On-board Intel Atom™ Processor D2700/N2600; 2.6 Expansion slot 2.2 Memory · Two MINI-PCIe slots. · Supports 204-Pin DDR3 1066 MHz memories * 1;... -
Page 5: Layout Of Motherboard
www.giadatech.com 1. Layout of motherboard 背 面 正 面 1 COM 1 19. JLVDS 10. USB 2. Installing memory 2. VGA 20. JLVDS POWER 11. CMOS 3. LPT 21.CPU_FAN 12. SATA 0,1 Please install the memory in accordance with the following procedures: 4. -
Page 6: Install Expansion Slot Card
www.giadatech.com 3. Install expansion slot card Installing Mini-PCIE extended devices At the rear panel of motherboard is two Mini-PCIE extended slots, to which the user can connected WIFI module and Bluetooth module etc. If the user use a module type mSATA on slot 2, then can just use SINGLE SATA HDD since MI-PCIE2 share same signal with SATA1. -
Page 7: Motherboard Jumper Setting
www.giadatech.com 4. Motherboard jumper setting Note:The user should notice that all sockets are marked with PIN1. The mark “#” indicates the ex-factory default values. 4.1. SATA0/SATA1 (Serial ATA flat-cable sockets) Serial ATA sockets can reach a transmission speed of 300MB/s, and you can connect your Serial ATA device to this socket. -
Page 8: F_Usb2
www.giadatech.com 4.4. F_USB2 (frond-end USB pin) In case the USB ports on the rear panel of the machine case are not enough, the user can use the two sets of extension USB pins provided by this motherboard. These ports support USB 2.0 devices. The definitions of the ports are described below: USB+IR Signal... -
Page 9: F_Audio
www.giadatech.com 4.5. F_ AUDIO(Pins for front-end audio adapter) 4.6. COM Needle inserted definition These audio adapter ports allow you to connect to the wire harness of the audio adapter. After connection, you can easily control the audio output/microphone through the front panel of the host (Note: Don’t connect the wire to Pin 4). The definitions of the ports are described below: Definition Definition... -
Page 10: Jlvds
www.giadatech.com 4.7. JLVDS(LVDS 30pin) LVDS Power and control signal interface Signal Signal LVDS_A_TXDN0 LVDS_A_TXDP0 LVDS_A_TXDN1 LVDS_A_TXDP1 LVDS_A_TXDN2 LVDS_A_TXDP2 Signal LVDS_A_TXCN LVDS_A_TXCP LCD_BLT_VCC LVDS_A_TXDN3 LVDS_A_TXDP3 LCD_BKL_ON LVDS_B_TXDN0 LVDS_B_TXDP0 LVDS_BAK_ADJ LCD_BKL_ON LCD_ADJ LVDS_B_TXDN1 LVDS_B_TXDP1 LVDS_B_TXDN2 LVDS_B_TXDP2 HXSWF2.0_1X6 LVDS_B_TXCN LVDS_B_TXCP LVDS_B_TXDN3 LVDS_B_TXDP3 LVDS_PWR LVDS_PWR LVDS_PWR... -
Page 11: Gpio
www.giadatech.com 4.8. GPIO 4.9 VGA J 19 R 989 0/4/5% D D C_D ATA D D C_C LK H XSWF 2.0_1X12 4.10 PS/2 Definition Definition PS2POWER GPIO7 KBDATA KBCLK 3.3V GPIO14 MSDATA GPIO0 GPIO9 MSCLK GPIO10 GPIO15 GPIO6 HD/1*6P/2.0 GPIO13... -
Page 12: Autopw_On
www.giadatech.com 4.11 AUTOPW_ON Definition Definition 3.3V 3.3V 3.3V -12V PS-ON AUTOPW _ON AUTO_PW R_ON BUTTON_PSW 3*1 PIN 2.54mm 5VSB 4.12 Power ATX20 Pin 4.13 F_ PANEL (Front-end control panel) This socket is used to connect the flat cables on the front-end panel. -
Page 13: Rear Panel Interface
The descriptions relating to BIOS in this Manual can only be used for reference +HDLED（VCC） +PLED(VCC) as the BIOS version of the motherboard is upgraded continuously. Giada provides no guarantee that the contents in this Manual be consistent with the PW_BN RST_SW information you acquire. -
Page 14: Main Menu
www.giadatech.com 1. Main menu you can press DEL to enter the BIOS interface if no error is found. If the indicative information disappears before you can act, you can shut off the When the system enters the CMOS Setup menu, you can see the main menu computer and turn on it again, or you can press the key RESET on the machine on the upper part of the screen, as shown in Figure 3.1. -
Page 15: Main (Standard Cmos Setup)
www.giadatech.com · Exit (option of exit) 3. Advanced (Advanced BIOS setup) This item includes load optimal defaults/load failsafe defaults value/discard changes/ discard changes and exit. 2. Main (standard CMOS setup) Fig 3.3 4. Boot Configuration Fig 3.2 · System time (hh:mm:ss) Use this item to set the time for the computer, with the format as “hour/minute/second”. -
Page 16: Security Setup
www.giadatech.com · · Interrupt 19 Capture [Disabled] Quiet Boot To start the system quietly. If you use some PCI extension cards with built-in firmware program (like · Add On ROM Display Mode [Force BIOS] SCSI extension card) and you want to start the system through Interrupt 19, This item allows you to set the display mode of the device’s firmware you can set this item as [Enabled]. -
Page 17: Exit
www.giadatech.com If this function is selected, the following information will appear: 6. Exit Enter New Password hhhhhh Then, enter the password with not more than eight characters and press <Enter>. BIOS will requires to enter the password again. Once you enter it again, BIOS will save the set password. -
Page 18: Software Installation
www.giadatech.com IV. Software installation NOTE：Pictures below just showing the driver install steps, please see the real In Fig 4.1, click "Driver ", another UI appears as shown in Fig 4.2. product for detailed information. 1. Install driver for motherboard After you complete the installation of the operating system, you should then install the driver for the motherboard. -
Page 19: Install Driver For Chipset
www.giadatech.com 1.1. Installing driver for Chipset 1.2 Install Sound card driver After you click “Install” behind the “Intel Chipset driver” in the interface of After you click “Install” behind the “Realtek HD audio driver” in the interface of Fig. 4.2, a dialog box as shown in Fig. 4.4 will pop up. Then you can click “Next” Fig. -
Page 20: Install Driver For On-Board Lan Chip
www.giadatech.com 1.3 Installing driver for on-board LAN chip 2. HD-AUDIO sound card setup After you click “Install” behind the “Realtek 10/100/1000 LAN Driver” in the · For Windows XP SP2: interface of Fig. 4.2, a dialog box as shown in Fig. 4.5 will pop up. Then you The control panel of the audio adapter will appear after the driver is installed, can click “Next”... - Page 21 www.giadatech.com After the initial installation of the driver, the default state of microphone is For Windows Vista: mute. You need to turn it on manually, as shown in Fig. 4.7 and 4.8. After the driver for the audio adapter is installed, you can click the Audio Manager at the lower right corner.
- Page 22 www.giadatech.com Click the right upper part of the control interface—Advanced Setup for Device, If a MIC is used, please select the corresponding front or rear mode and set the the interface shown in Fig. 4.11 will pop up. Then select “separate all input jacks device as default.
- Page 23 www.giadatech.com Select Redistribution of Connectors. Then an interface will pop up, as Changes or modifications not expressly approved by the party responsible for shown in Fig. 4.14. After that, set the corresponding output. compliance could void the user's authority to operate the equipment NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.