Operation - Haier HPU-18H03/HBF Operation Manual

Operation

Base Operation
Unit start
Press ON/OFF on the indoor unit ,or press ON/OFF on the
remote controller,unit starts.
The liquid crystal will display the working state of
last time (Except Timer and Sleep )
Select operation mode
Press HEAT,DRY,COOL ,or AUTO button,For each
press,operation mode changes.
Fan speed selection
Press FAN button. For each press,fan speed
changes as follows:
Remote controller:
Display
circulated
AUTO
LOW
Air conditioner is running under displayed fan speed.
When FAN is set to AUTO,the air conditioner automatically
adjusts the fan speed according to room temperature.
Unit stop
Press ON/OFF button, the unit stops.
Air Flow Direction Adjustment
Left and right air flow
direction display
Up and down air flow
direction display
Pos.1
Pos.1
Pos.2
TURBO
Pos.2
Pos.3
Pos.4
Pos.3
Pos.5
Pos.4
Pos.6
SLEEP
Pos.5
Pos.7
Fig.1
Pos.8
(Auto swing)
Sleep Operation
Operation Mode
In COOL,DRY mode
1 hours after SLEEP mode starts, temp. will become 1
for further 6 hours then stops. Temp. is higher than temp.setting so that
room temperature won't be too low for your sleep.
In HEAT mode
1 hours after SLEEP mode starts, temp. will become 2
for further 3 hours then stops. Temp. is lower than temp.setting so that
room temperature won't be too high for your sleep.
In FAN mode
It has no SLEEP function.
MED
HI
Horizontal flap Vertivcal flap
Pos.1
Pos.1
Pos.2
Pos.2
Pos.3
Pos.3
Pos.4
Pos.5
Pos.4
Pos.6
Pos.5
(Auto swing)
Pos.7
Fig.3
Pos.8
Fig.2
(Auto swing)
Fig.4
Control panel display
Auto Operation
AUTO
Fuzz
COOL Operation
HIGH
COOL
DRY Operation
AUTO
Dehu
FAN Operation
LOW
FAN
HEAT Operation
LOW
HEAT
Up and down air flow direction adjustment
For each press of SWING button,the position of horizontal
flap and the air flow direction on remote controller display
changes as follows according to different operation models:
Pos.1 Pos.2 Pos.3 Pos.4
Remote
controller
COOL/DRY/FAN
HEAT/AUTO mode Horizontal Pos.1 Pos.2 Pos.3 Pos.4 Pos.5
flap
Note:When the unit is turned off by the remote controller or the control panel,the horizontal flap will close.
When the power supply is cut off directly, the horizontal flap will not close. Please use the remote controller
or the control panel to stop the unit.Do not start or stop the operation by disconnecting the power supply
and so on
HEALTH Operation
Press button to enter additional options, when cycle display to
will flash, and then press
function, please enter additional options again and to cancel health function.
Note:
When the HEALTH mode is set, the flap will keep the position you set. It is advisable not to keep horizontal
flap at downward positionfor a long time in COOL or DRY mode,otherwise,condensate water might occur.
Left and right air flow adjustment
Press button to enter additional options, when cycle display to
will flash. And then press
Press . For each press, move the vertical blade by a knob on air conditioner
to adjust left and right direction referring to Fig. displays as follows:
Pos.1 Pos.2 Pos.3 Pos.4 Pos.5 Pos.6 Pos.7 Pos.8
Remote
controller
Pos.1 Pos.2 Pos.3 Pos.4 Pos.5 Pos.6 Pos.7 Pos.8
Vertical
flap
SLEEP operation starts
Rises 1
Rises 1
Temp.setting
Remote controller display
TURBO
SLEEP
Remote controller button
Pos.5
,enter to health function. When cancel the
, enter to Left and right air flow function.
SLEEP operation stops
In COOL DRY mode
SLEEP operation starts
Unit stop
In HEAT mode
Decreases 2
Decreases 2
Temp.setting
(Fig.1)
(Fig.3)
,
,
(Fig.2)
(Fig.4)
SLEEP operation stops
Rises 1
Unit stop