Page 1
PRE60 AudioPhilE PREAmPlifiER, dAC, StREAmER User Guide...
Page 2
However, our policy is one of continuous development and so the information is subject to change without notice, and does not represent a commitment on the part of Primare AB. Primare is a trademark of Primare AB. This guide was produced by Human-Computer Interface Ltd.
Connecting to the Internet AdditionAl infoRmAtion Best sound uSinG thE PRE60 Burn-in Front panel controls RS232 Using the Primare App Trigger input/output Selecting a source Changing the volume indEx Changing the display brightness Changing the balance PRE60 Audiophile Preamplifier, dAC, Streamer user Guide...
Connect the PRE1 or PRE2 L and R outputs from the • Two batteries for the remote control. PRE60 to the L and R balanced inputs in the power See Best sound , page 3, for information about getting amplifier, using high quality XLR cables.
Press briefly to mute the sound When disposing of old batteries please be considerate to Press and hold to display the settings menu the environment. Control the CD player Change the balance Change the display brightness PRE60 Audiophile Preamplifier, dAC, Streamer user Guide...
You can connect up to three digital optical inputs and one four unbalanced sources to the analogue inputs on the digital coax input to the PRE60 to allow you to play digital You can connect an iPod, iPhone, iPad, or other UPnP back panel.
ConnECtinG to A ComPutER ConnECtinG to thE intERnEt You can connect a USB drive to the PRE60, to allow you to You can connect the PRE60 to a Windows PC or You can connect the PRE60 to the Internet via either Wi-Fi...
ChAnGinG thE volumE Selects an input. The front panel display shows the current balance The PRE60 allows you to vary the volume from 0 (silence) setting, where 00LR-9 corresponds to the leftmost In the settings menus: Selects a setting. to 79 (maximum).
22 Status Enabled To exit from the settings menus Alias • Source offset Hold down the button on the front panel, or press Input 6 the MENU button on the remote control. PRE60 Audiophile Preamplifier, dAC, Streamer user Guide...
To set the IR input The alias editor is displayed: To set the start-up balance • Set the IR input to Front to control the PRE60 using a Input settings vol 22 Set the Balance setting to the balance you want to use:...
SEttinGS options on the Ethernet settings or WLAN settings menu, To connect the PRE60 to an Ethernet network you need to If you have a WLAN (Wi-Fi) network, the simplest way to to connect the PRE60 to an Ethernet network.
Ethernet settings The PRE60 will then scan for firmware on the network. Wlan settings Name PRE60 If the firmware on your PRE60 is up to date the menu will Connected Wireless show Version is up to date: Firmware settings vol 22...
1 x Coax output transmitting at 192 kHz. Always connected to the active input source. Some features, like playing media from USB thumb drive, USB-connected iPhone, iPod Touch, or iPad, and playing vTuner, require the use of the Primare App. PRE60 Audiophile Preamplifier, dAC, Streamer user Guide...
You will notice a further smaller improvement in sound quality for at least another 3 days’ playing. RS The RS232 input allows you to connect the PRE60 to a controller system. For more information please contact Primare or visit www.primare.net.
Page 17
PRE60 Audiophile Preamplifier, dAC, Streamer user Guide...
Page 18
E. the appliance has been dropped or the enclosure a bathtub, washbowl, kitchen sink, in a wet basement or the appliance. damaged. near a swimming pool, etc. PRE60 Audiophile Preamplifier, dAC, Streamer user Guide...