Spare Parts, Service And Disposal - Remak DoorMaster C1 Installation And Operating Instructions Manual

Spare parts, service and disposal

Check procedure:
Verify the air curtain control possibilities, refer to

table #9 on page 20.
Using a resistor, check the closing of the correspon-

ding contacts in the controller/sensor/door contact.
The air curtain functionality can be verified by inter-

connecting the corresponding terminals inside the air
curtain.
Interconnect these terminals:

Speed controller (the fans do not operate, the speed

stages do not operate):
LV + Q1 or LV + Q2 or LV + Q3
Heating output controller (the air curtain does not

heat):
LE + Q1E or LE + Q2E or LE + Q3E
Room thermostat (the air curtain does not heat):

TK + TK
Door contact (the air curtain does not start):

DK1 + DK2
Other Possible Problems
The air curtain still runs after it has been turned off.

The air curtain with a cooling function - if it is turned off
and the heating coil battery is hot at that moment, the
air curtain fan will be automatically started up to the
maximum speed until the interior of the air curtain has
safely cooled down. This is not a failure, wait until the
air curtain automatically stops.
Table 5 – fuses
DoorMaster type C1
C1-N-xx C1-W-xx
FU1 –
FU2 6.3 A
FU3 –
DoorMaster typ D2 (heating N and W)
D2-N-10 D2-N-15
D2-W-10 D2-W-15
FU1
FU2 4.0 A
FU3
FU4
DoorMaster type D2 (heating E1 and E2)
D2-E1-10 D2-E1-15
D2-E2-10 D2-E2-15
FU1
FU2 4.0 A
FU3
FU4
Spare Parts
The air curtain is delivered without spare parts. If any
spare parts are needed, they can be ordered from
REMAK a.s.
C1-E1-xx C1-E2-xx
315 mA
6.3 A
315 mA
D2-N-20 D2-N-25
D2-W-20 D2-W-25
1.0 A
6.3 A 6.3 A 10 A
500 mA
–
D2-E1-20 D2-E1-25
D2-E2-20 D2-E2-25
1.0 A
6.3 A 6.3 A 10 A
500 mA
315 mA
Spare Filter Inserts
Please fill in the size of air curtain when ordering spare
filter inserts. Filter inserts can be regenerated by vacuu-
ming or washing in clean water.
Order code:
DM FND 100 (for D2-XX-100 air curtains)
DM FND 150 (for D2-XX-150 air curtains)
DM FND 200 (for D2-XX-200 air curtains)
DM FND 250 (for D2-XX-250 air curtains)
Service
Guarantee and servicing can be ordered at the fo-
llowing address:
REMAK a.s., Zuberská 2601, CZ-756 61 Rožnov pod
Radhoštěm, Czech republic
Phone: +420 571 877 787, fax: +420 571 877 777
Service will be provided by an authorized service com-
pany.
Disposal
During the air curtain's service life, it is necessary to
ensure safe and environmentally-friendly disposal of all
replaced parts and service materials. When disposing
of materials, it is necessary to observe the applicable
local environmental protection and waste disposal re-
gulations. In case of final liquidation of the device once
its service life has elapsed, it is necessary to follow the
policy of sorted waste disposal; this means to respect
differences in materials and their composition. It is ne-
cessary to hire a provider specialized in sorted waste
disposal in accordance with the applicable local stan-
dards and regulations. We recommend metal parts be
scrapped and other parts be disposed of in accordance
with sorted waste regulations by waste disposal or was-
te incineration in an incineration plant.
After exceeding its service life limit, the unit belongs
to waste group Q14 according to the Waste Act
(No.185/2001 Sb.) The unit includes metal parts, insu-
lation material (soft expanded polyurethane), elastomer,
filtration material (polyurethane foam), electronic parts
and plastic side walls.
Waste Classification
Materials used to pack the product:
 15 01 01 cardboard box
(paper and cardboard packaging)
 15 01 02 polyester packaging pads
(plastic packaging)
 15 01 03 pallet
(wooden packaging)
Disabled device and its parts
 16 02 06 metal and aluminium parts of the air
curtain, insulating material
(other items from disabled devices)
 15 02 03 filtering materials, plastic side walls
(plastics)
 16 02 15 electrical parts
(dangerous items from disabled devices)
Air curtains
25