Page 1 2011 Buick Lucerne Owner Manual In Brief ..........1-1 Theft-Deterrent Systems .
Page 2 2011 Buick Lucerne Owner Manual Service and Appearance Care ....6-1 Maintenance Schedule ......7-1 Service .
Page 3: Canadian Owners
For vehicles first sold in Canada, can be found. substitute the name General Motors of Canada Limited for Buick Motor Division wherever it appears in this manual. Keep this manual in the vehicle for quick reference. Litho in U.S.A.
Page 4: Vehicle Symbols
Safety Warnings and Symbols A circle with a slash through it is a safety Warning messages found on vehicle labels and in this symbol which means Do manual describe hazards and what to do to avoid or Not, Do not do this, or reduce them.
Page 5: Index
Vehicle Symbol Chart : Fuel Gauge Here are some additional symbols that may be found on : Fuses the vehicle and what they mean. For more information : Headlamp High/Low-Beam Changer on the symbol, refer to the Index. : LATCH System Child Restraints : Airbag Readiness Light : Malfunction Indicator Lamp : Air Conditioning...
Page 6 NOTES...
Page 7: In Brief
Section 1 In Brief Instrument Panel ........1-2 Vehicle Features .
Page 8 Instrument Panel...
Page 9 A. Outlet Adjustment on page 4 25 M. Data Link Connector (DLC) (Out of View). See Malfunction Indicator Lamp on page 4 37 B. DIC Operation and Displays on page 4 42 N. Parking Brake on page 3 26 C. Turn Signal/Multifunction Lever on page 4 4 O.
Page 10: Initial Drive Information
Initial Drive Information Press to lock all doors. This section provides a brief overview about some of Lock and unlock feedback can be personalized. the important features that may or may not be on your Press and hold for approximately one second to specific vehicle.
Page 11: Trunk Release
When the vehicle starts, the parking lamps will turn on Power Door Locks and remain on as long as the engine is running. The On vehicles with power door locks, the switches are doors will be locked and the climate control system may located on the front doors.
Page 12: Seat Adjustment
Windows Seat Adjustment Power Seats On vehicles with power windows, the switches are on the driver door armrest. Each passenger door has a switch that controls only that window. To adjust a power seat: Press the switch to lower the window. Pull the switch up to raise it.
Page 13: Reclining Seatbacks
Reclining Seatbacks Lumbar Adjustment To raise or recline the seatback, tilt the top of the Use the round control on the outboard side of the seat control forward or rearward. to adjust the lumbar support. See Reclining Seatbacks on page 2 9. See Power Lumbar on page 2 4 for more information.
Page 14: Memory Features
Memory Features To recall the memory positions, press and release 1 or 2. The vehicle must be in P (Park). A single beep On vehicles with the memory feature, the controls on will sound. The seat, outside mirrors, and power the driver door are used to program and recall memory steering column, if equipped, will move to the positions settings for the driver seat, outside mirrors, and the...
Page 15: Heated Seats
Heated Seats Heated and Ventilated Seats If available, the buttons are on the front doors. To If available, the buttons are on the front doors. To operate, the ignition must be on. operate, the ignition must be on. : Press to heat the seat and seatback. : Press to heat the seat and seatback.
Page 16: Head Restraint Adjustment
Head Restraint Adjustment Safety Belts The vehicle's front seats have adjustable head restraints in the outboard seating positions. Do not drive until the head restraints for all occupants are installed and adjusted properly. To achieve a comfortable seating position, change the seatback recline angle as little as necessary while keeping the seat and the head restraint height in the proper position.
Page 17: Sensing System For Passenger Airbag
Sensing System for Passenger Mirror Adjustment Airbag Exterior Mirrors The passenger sensing system will turn off the right Controls for the outside front passenger frontal airbag and seat mounted side power mirrors are located impact airbag under certain conditions. The driver on the driver door airbags and roof rail airbags are not affected by this.
Page 18: Interior Mirror
Interior Mirror To adjust the steering wheel: The vehicle has an automatic dimming inside rearview 1. Hold the wheel and pull the lever toward you. mirror. Automatic dimming reduces the glare of lights 2. Move the steering wheel up or down. from behind the vehicle.
Page 19: Interior Lighting
Interior Lighting Exterior Lighting Courtesy Lamps The exterior lamp control is located on the When any door is opened, the interior lamps turn on to instrument panel to the enter and exit the vehicle. Turn the instrument panel left of the steering wheel. brightness control located on the left side of the steering wheel, completely clockwise to manually turn...
Page 20: Windshield Wiper/Washer
For more information, see: 9 : Turns the wipers off. Exterior Lamps on page 4 10. : Press and release this paddle, located at the top of the turn signal/multifunction lever, to spray washer Daytime Running Lamps (DRL) on page 4 11. fluid on the windshield.
Page 21: Vehicle Features
This system allows the driver and passenger to control Vehicle Features the temperature settings separately. Radio(s) A. Driver and Passenger E. Air Conditioning Temperature Controls F. Outside Air B. Fan Control G. Air Recirculation C. Display Radio with CD (MP3) H.
Page 22: Storing A Favorite Station
Satellite Radio Service, MP3, and RDS 3. Press and the HR, MIN, MM, DD, YYYY (hour, Features): Press this button to display additional minute, month, day, and year) displays. text information related to the current FM-RDS or XM 4. Press the softkey located below any one of the station, or MP3 song.
Page 23: Steering Wheel Controls
Portable Audio Devices (Auxiliary Steering Wheel Controls Input or USB Port) For vehicles with audio steering wheel controls, This vehicle may have an auxiliary input jack and a some audio controls USB port, located on the audio faceplate. External can be adjusted at the ®...
Page 24 reaching the destination. In addition, the system can : Press to seek the next radio station, the next track help locate a variety of points of interest (POIs), such as or chapter while sourced to the CD or DVD slot, or to banks, airports, restaurants, and more.
Page 25 Cruise Control : Press to customize the feature settings on your vehicle. See DIC Vehicle Customization on page 4 58 The cruise control buttons for more information. are located on the left : Press to reset certain DIC features and to side of the steering wheel.
Page 26 Lane Departure Warning (LDW) Side Blind Zone Alert (SBZA) For vehicles with LDW, it is intended to help avoid lane For vehicles with this feature, it may alert you to change collisions. It provides a warning if the vehicle is vehicles located in your side blind zone.
Page 27: Ultrasonic Parking Assist
Ultrasonic Parking Assist Universal Remote System For vehicles with this feature, it uses sensors on the rear bumper to detect objects while parking the vehicle. It operates at speeds less than 8 km/h (5 mph) while in R (Reverse). Keep the sensors on the vehicle's rear bumper clean to ensure proper operation.
Page 28: Performance And Maintenance
Performance and Maintenance Tire Pressure Monitor This vehicle may have a Tire Pressure Monitor Traction Control System (TCS) System (TPMS). The traction control system limits wheel spin. The The TPMS warming light system turns on automatically every time the vehicle is alerts you to a significant started.
Page 29: Driving For Better Fuel Economy
Tire Sealant and Compressor Kit Fuel E85 (85% Ethanol) This vehicle may come with a jack and spare tire or a Vehicles that have a FlexFuel badge and a yellow tire sealant and compressor kit. The kit can be used to fuel cap can use either unleaded gasoline or ethanol seal small punctures in the tread area of the tire.
Page 30: Roadside Assistance Program
Roadside Assistance Program OnStar U.S.: 1-800-252-1112 TTY Users: 1-888-889-2438 Canada: 1-800-268-6800 As the owner of a new Buick, you are automatically enrolled in the Roadside Assistance program. See Roadside Assistance Program on page 8 7 for more information. ® OnStar...
Page 31 Crisis Assist, Stolen Vehicle Assistance, Vehicle OnStar service can t work unless your vehicle is Diagnostics, Remote Door Unlock, Roadside in a place where OnStar has an agreement with a Assistance, Turn by Turn Navigation and Hands Free wireless service provider for service in that area, and Calling are available on most vehicles.
Page 32: Onstar Steering Wheel Controls
OnStar Steering Wheel Controls Your Responsibility This vehicle may have a Talk/Mute button that can be Increase the volume of the radio if the OnStar Advisor used to interact with OnStar Hands-Free calling. See cannot be heard. Audio Steering Wheel Controls on page 4 94 for more If the light next to the OnStar buttons is red, the system information.
Page 33: Table Of Contents
Section 2 Seats and Restraint System Head Restraints ........2-2 Lower Anchors and Tethers for Children (LATCH) .
Page 34: Head Restraints
Head Restraints The front seats have adjustable head restraints in the outboard seating positions. WARNING: With head restraints that are not installed and adjusted properly, there is a greater chance that occupants will suffer a neck/spinal injury in a crash. Do not drive until the head restraints for all occupants are installed and adjusted properly.
Page 35: Front Seats
Front Seats Power Seats Pull the head restraint up to raise it. To lower the head restraint, press the button, located on the top of the seatback, and push the restraint down. Push down on the head restraint after the button is released to make sure that it is locked in place.
Page 36: Power Lumbar
On vehicles with four-way lumbar, press the front For vehicles with power reclining seatbacks, see Power or rear of the control to increase or decrease Reclining Seatbacks under Reclining Seatbacks on lumbar support. Press the top or bottom of the page 2 9.
Page 37 The column of three lights near the buttons shows the If available, the buttons current temperature setting. With each press of the are on the front doors. button, the seat will change to the next lower setting, and then to the off setting. The lights indicate three for the highest setting and one for the lowest.
Page 38 Heated and Ventilated Seats (Ventilated Seat Cushion and Seatback): Press to cool the seat cushion and seatback. Press the desired button once to turn this feature on at WARNING: the highest setting. A light on the button turns on to show which feature is on.
Page 39: Memory Seat And Mirrors
Memory Seat and Mirrors To recall the memory positions, press and release 1 or 2. The vehicle must be in P (Park). A single beep On vehicles with the memory feature, the controls on will sound. The seat, outside mirrors, and power the driver door are used to program and recall memory steering column, if equipped, will move to the positions settings for the driver seat, outside mirrors, and the...
Page 40 To stop recall movement, press one of the memory or If the easy exit feature is programmed on in the vehicle power mirror buttons, power seat controls, or the power customization menu, automatic driver seat and power steering column switch. steering column movement occur when the ignition key is removed.
Page 41: Reclining Seatbacks
Reclining Seatbacks WARNING: Sitting in a reclined position when the vehicle is in motion can be dangerous. Even when buckled up, the safety belts cannot do their job when reclined like this. The shoulder belt cannot do its job because it will not be against your body.
Page 42: Manual Reclining Seatbacks
Manual Reclining Seatbacks WARNING: You can lose control of the vehicle if you try to adjust a manual driver seat while the vehicle is moving. The sudden movement could startle and confuse you, or make you push a pedal when you do not want to.
Page 43: Center Seat
To return the seatback to the upright position: Center Seat 1. Lift the lever fully without applying pressure to the seatback, and the seatback will return to the upright position. 2. Push and pull on the seatback to make sure it is locked.
Page 44: Rear Seats
Rear Seats WARNING: (Continued) Rear Seat Pass-Through Door might not be, if you are buckled up. Always fasten The vehicle has a pass through door that provides your safety belt, and check that your passenger(s) access to the trunk from the rear seats. See Rear Seat are restrained properly too.
Page 45: Why Safety Belts Work
In most states and in all Canadian provinces, the law Why Safety Belts Work requires wearing safety belts. Here is why: When you ride in or on anything, you go as fast as You never know if you will be in a crash. If you do have it goes.
Page 46 Put someone on it. Get it up to speed. Then stop the vehicle. The rider does not stop. 2-14...
Page 47 The person keeps going until stopped by something. In or the instrument panel... a real vehicle, it could be the windshield... 2-15...
Page 48: Questions And Answers About Safety Belts
Questions and Answers About Safety Belts Q: Will I be trapped in the vehicle after a crash if I am wearing a safety belt? A: You could be whether you are wearing a safety belt or not. But your chance of being conscious during and after an accident, so you can unbuckle and get out, is much greater if you are belted.
Page 49: How To Wear Safety Belts Properly
Q: If I am a good driver, and I never drive far from How to Wear Safety Belts Properly home, why should I wear safety belts? This section is only for people of adult size. A: You may be an excellent driver, but if you are in a Be aware that there are special things to know about crash even one that is not your fault...
Page 50 First, before you or your passenger(s) wear a safety In a crash, this applies force to the strong pelvic bones belt, there is important information you should know. and you would be less likely to slide under the lap belt. If you slid under it, the belt would apply force on your abdomen.
Page 51 Q: What is wrong with this? WARNING: You can be seriously hurt if the shoulder belt is too loose. In a crash, you would move forward too much, which could increase injury. The shoulder belt should fit snugly against your body. A: The shoulder belt is too loose.
Page 52 Q: What is wrong with this? WARNING: You can be seriously hurt if the lap belt is too loose. In a crash, you could slide under the lap belt and apply force on your abdomen. This could cause serious or even fatal injuries. The lap belt should be worn low and snug on the hips, just touching the thighs.
Page 53 Q: What is wrong with this? WARNING: You can be seriously injured if the belt is buckled in the wrong place like this. In a crash, the belt would go up over your abdomen. The belt forces would be there, not on the pelvic bones. This could cause serious internal injuries.
Page 54 Q: What is wrong with this? WARNING: You can be seriously injured if the belt goes over an armrest like this. The belt would be much too high. In a crash, you can slide under the belt. The belt force would then be applied on the abdomen, not on the pelvic bones, and that could cause serious or fatal injuries.
Page 55 Q: What is wrong with this? WARNING: You can be seriously injured if you wear the shoulder belt under your arm. In a crash, your body would move too far forward, which would increase the chance of head and neck injury. Also, the belt would apply too much force to the ribs, which are not as strong as shoulder bones.
Page 56 Q: What is wrong with this? WARNING: You can be seriously injured by not wearing the lap-shoulder belt properly. In a crash, you would not be restrained by the shoulder belt. Your body could move too far forward increasing the chance of head and neck injury.
Page 57 Q: What is wrong with this? WARNING: You can be seriously injured by a twisted belt. In a crash, you would not have the full width of the belt to spread impact forces. If a belt is twisted, make it straight so it can work properly, or ask your dealer to fix it.
Page 58: Lap-Shoulder Belt
Lap-Shoulder Belt All seating positions in the vehicle have a lap-shoulder except for the center front passenger position (if equipped), which has a lap belt. See Lap Belt on page 2 32 for more information. The following instructions explain how to wear a lap-shoulder belt properly.
Page 59 4. If equipped with a shoulder belt height adjuster, move it to the height that is right for you. See Shoulder Belt Height Adjuster later in this section for instructions on use and important safety information. To unlatch the belt, push the button on the buckle. The belt should return to its stowed position.
Page 60 Shoulder Belt Height Adjuster Safety Belt Pretensioners The vehicle has a shoulder belt height adjuster for the This vehicle has safety belt pretensioners for front driver and right front passenger seating positions. outboard occupants. Although the safety belt pretensioners cannot be seen, they are part of the Adjust the height so the shoulder portion of the belt safety belt assembly.
Page 61: Rear Safety Belt Comfort Guides
Rear Safety Belt Comfort Guides This vehicle may have rear shoulder belt comfort guides for each outside passenger position in the rear seat. If not, they are available through your dealer. The guides may provide added safety belt comfort for older children who have outgrown booster seats and for some adults.
Page 62 WARNING: A safety belt that is not properly worn may not provide the protection needed in a crash. The person wearing the belt could be seriously injured. The shoulder belt should go over the shoulder and across the chest. These parts of the body are best able to take belt restraining forces.
Page 63: Safety Belt Use During Pregnancy
Safety Belt Use During Pregnancy Safety belts work for everyone, including pregnant women. Like all occupants, they are more likely to be seriously injured if they do not wear safety belts. 4. Buckle, position, and release the safety belt as described previously in this section.
Page 64: Lap Belt
Lap Belt This part is only for the lap belt. To learn how to wear a lap-shoulder belt, see Lap-Shoulder Belt on page 2 26. The vehicle may have a center seating position. When you sit in the center front seating position, you have a lap safety belt, which has no retractor.
Page 65: Safety Belt Extender
Safety Belt Extender Child Restraints If the vehicle's safety belt will fasten around you, you Older Children should use it. But if a safety belt is not long enough, your dealer will order you an extender. When you go in to order it, take the heaviest coat you will wear, so the extender will be long enough for you.
Page 66 Buckle the lap-shoulder belt. Does the shoulder Also see Rear Safety Belt Comfort Guides under belt rest on the shoulder? If yes, continue. If no, try Lap-Shoulder Belt on page 2 26. using the rear safety belt comfort guide. See Rear According to accident statistics, children and infants Safety Belt Comfort Guides under Lap-Shoulder are safer when properly restrained in a child restraint...
Page 67 WARNING: (Continued) head and neck injury. The child might also slide under the lap belt. The belt force would then be applied right on the abdomen. That could cause serious or fatal injuries. The shoulder belt should go over the shoulder and across the chest. WARNING: Never do this.
Page 68: Infants And Young Children
Infants and Young Children Airbags plus lap shoulder belts offer protection for adults and older children, but not for young children and Everyone in a vehicle needs protection! This includes infants. Neither the vehicle's safety belt system nor its infants and all other children. Neither the distance airbag system is designed for them.
Page 69 WARNING: (Continued) If you must secure a forward-facing child restraint in the right front seat, always move the front passenger seat as far back as it will go. WARNING: Never do this. Children who are up against, or very close to, any airbag when it inflates can be seriously injured or killed.
Page 70 Q: What are the different types of add-on child restraints? WARNING: (Continued) A: Add-on child restraints, which are purchased by the vehicle's owner, are available in four basic types. and its head weighs so much compared with Selection of a particular restraint should take into the rest of its body.
Page 71: Child Restraint Systems
Child Restraint Systems A rear-facing infant seat (A) provides restraint with the seating surface against the back of the infant. The harness system holds the infant in place and, in a crash, acts to keep the infant positioned in the restraint. A booster seat (C-D) is a child restraint designed to improve the fit of the vehicle's safety belt system.
Page 72: Securing The Child Within The Child Restraint
Securing an Add-On Child Restraint in Keep in mind that an unsecured child restraint can move around in a collision or sudden stop and injure the Vehicle people in the vehicle. Be sure to properly secure any child restraint in the vehicle even when no child is in it.
Page 73: Where To Put The Restraint
Where to Put the Restraint WARNING: (Continued) According to accident statistics, children and infants are safer when properly restrained in a child restraint system or infant restraint system secured in a rear injured or killed if the right front passenger airbag seating position.
Page 74: Lower Anchors And Tethers For Children (Latch)
Depending on where you place the child restraint and WARNING: the size of the child restraint, you may not be able to access adjacent safety belt assemblies or LATCH anchors for additional passengers or child restraints. A child in a child restraint in the center front seat Adjacent seating positions should not be used if the can be badly injured or killed by the frontal child restraint prevents access to or interferes with the...
Page 75 Make sure that a LATCH-compatible child restraint Lower Anchors is properly installed using the anchors, or use the vehicle's safety belts to secure the restraint, following the instructions that came with that restraint, and also the instructions in this manual. When installing a child restraint with a top tether, you must also use either the lower anchors or the safety belts to properly secure the child restraint.
Page 76: Top Tether Anchor
Top Tether Anchor Some child restraints that have a top tether are designed for use with or without the top tether being attached. Others require the top tether always to be attached. In Canada, the law requires that forward-facing child restraints have a top tether, and that the tether be attached.
Page 77 To assist you in locating the lower anchors, each seating position with lower anchors has two labels, near the crease between the seatback and the seat cushion. To assist you in locating the top tether anchors, the top tether anchor symbol The top tether anchors are located under the covers is located on the cover.
Page 78: Securing A Child Restraint Designed For The Latch System
According to accident statistics, children and infants are safer when properly restrained in a child restraint WARNING: system or infant restraint system secured in a rear seating position. See Where to Put the Restraint on Do not attach more than one child restraint to a page 2 41 for additional information.
Page 79 Notice: Do not let the LATCH attachments rub 2. If the child restraint manufacturer recommends that against the vehicle s safety belts. This may damage the top tether be attached, attach and tighten the these parts. If necessary, move buckled safety belts top tether to the top tether anchor, if equipped.
Page 80 If the position you are If the position you using does not have are using has a fixed a headrest or head headrest or head restraint restraint and you are and you are using a dual using a dual tether, tether, route the tether route the tether over around the headrest or...
Page 81: Seat Position
Securing a Child Restraint in a Rear If more than one child restraint needs to be installed in the rear seat, be sure to read Where to Put the Seat Position Restraint on page 2 41. When securing a child restraint in a rear seating 1.
Page 82 4. Pull the shoulder belt all the way out of the 5. To tighten the belt, push down on the child retractor to set the lock. When the retractor lock restraint, pull the shoulder portion of the belt to is set, the belt can be tightened but not pulled out tighten the lap portion of the belt, and feed the of the retractor.
Page 83: Securing A Child Restraint In The Center Front Seat Position
6. If the child restraint has a top tether, follow the Securing a Child Restraint in the child restraint manufacturer's instructions regarding Center Front Seat Position the use of the top tether. See Lower Anchors and Tethers for Children (LATCH) on page 2 42 for more information.
Page 84: Securing A Child Restraint In The Right Front Seat Position
Securing a Child Restraint in the WARNING: Right Front Seat Position This vehicle has airbags. A rear seat is a safer place to A child in a rear-facing child restraint can be secure a forward-facing child restraint. See Where to seriously injured or killed if the right front Put the Restraint on page 2 41.
Page 85 If the child restraint has the LATCH system, see 2. Put the child restraint on the seat. Lower Anchors and Tethers for Children (LATCH) on 3. Pick up the latch plate, and run the lap and page 2 42 for how and where to install the child shoulder portions of the vehicle's safety belt restraint using LATCH.
Page 86 5. Pull the shoulder belt all the way out of the 6. To tighten the belt, push down on the child retractor to set the lock. When the retractor lock is restraint, pull the shoulder portion of the belt to set, the belt can be tightened but not pulled out of tighten the lap portion of the belt, and feed the the retractor.
Page 87: Airbag System
A roof-rail airbag for the driver and the passenger 7. Before placing a child in the child restraint, make seated directly behind the driver. sure it is securely held in place. To check, grasp the child restraint at the safety belt path and A roof-rail airbag for the right front passenger and attempt to move it side to side and back and forth.
Page 88 Here are the most important things to know about the airbag system: WARNING: WARNING: Airbags inflate with great force, faster than the blink of an eye. Anyone who is up against, or very close to, any airbag when it inflates can be You can be severely injured or killed in a crash if seriously injured or killed.
Page 89: Where Are The Airbags
The system checks the airbag electrical system for WARNING: malfunctions. The light tells you if there is an electrical problem. See Airbag Readiness Light on page 4 30 for more information. Children who are up against, or very close to, Where Are the Airbags? any airbag when it inflates can be seriously injured or killed.
Page 90 Driver Side shown, Passenger Side similar The right front passenger frontal airbag is in the The seat-mounted side impact airbags for the driver and instrument panel on the passenger side. right front passenger are in the side of the seatbacks closest to the door.
Page 91 WARNING: If something is between an occupant and an airbag, the airbag might not inflate properly or it might force the object into that person causing severe injury or even death. The path of an inflating airbag must be kept clear. Do not put anything between an occupant and an airbag, and do not attach or put anything on the steering wheel hub or on or near any other airbag...
Page 92: When Should An Airbag Inflate
If the vehicle hits a narrow object (like a pole), the When Should an Airbag Inflate? airbags could inflate at a different crash speed than if the vehicle hits a wide object (like a wall). Frontal airbags are designed to inflate in moderate to severe frontal or near-frontal crashes to help reduce If the vehicle goes into an object at an angle, the the potential for severe injuries mainly to the driver's or...
Page 93: What Makes An Airbag Inflate
Your vehicle also has a dual-depth passenger airbag In any particular crash, no one can say whether an that adjusts the restraint according to crash severity, airbag should have inflated simply because of the seat location, and safety belt status using electronic damage to a vehicle or because of what the repair frontal sensor(s) and other special sensors which costs were.
Page 94: How Does An Airbag Restrain
How Does an Airbag Restrain? Roof-rail airbags may still be at least partially inflated for some time after they deploy. Some components of In moderate to severe frontal or near frontal collisions, the airbag module may be hot for several minutes. For even belted occupants can contact the steering wheel location of the airbag modules, see What Makes an or the instrument panel.
Page 95 The vehicle has a feature that may automatically In many crashes severe enough to inflate the airbag, unlock the doors, turn on the interior lamps and hazard windshields are broken by vehicle deformation. warning flashers, and shut off the fuel system after Additional windshield breakage may also occur from the airbags inflate.
Page 96: Passenger Sensing System
Passenger Sensing System The passenger sensing system turns off the right front passenger frontal airbag and seat-mounted side impact The vehicle has a passenger sensing system for the airbag under certain conditions. The driver airbags and right front passenger position. The passenger airbag the roof-rail airbags are not affected by the passenger status indicator will be visible on the overhead console sensing system.
Page 97 The passenger sensing system is designed to turn off WARNING: the right front passenger airbag and seat mounted side impact airbag if: The right front passenger seat is unoccupied. A child in a rear-facing child restraint can be The system determines that an infant is present in seriously injured or killed if the right front a rear-facing infant seat.
Page 98 When the passenger sensing system has allowed the If the On Indicator is Lit for a Child airbags to be enabled, the on indicator will light and Restraint stay lit to remind you that the airbags are active. If a child restraint has been installed and the on For some children who have outgrown child restraints indicator is lit: and for very small adults, the passenger sensing...
Page 99 6. Restart the vehicle. If this happens, use the following steps to allow the system to detect that person and enable the right front If the on indicator is still lit, secure the child in the passenger frontal airbag and seat-mounted side impact child restraint in a rear seat position in the vehicle, airbag: and check with your dealer.
Page 100: Servicing Your Airbag-Equipped Vehicle
A thick layer of additional material, such as a blanket Servicing Your Airbag-Equipped or cushion, or aftermarket equipment such as seat Vehicle covers, seat heaters, and seat massagers can affect how well the passenger sensing system operates. Airbags affect how the vehicle should be serviced. We recommend that you not use seat covers or other There are parts of the airbag system in several places aftermarket equipment except when approved by...
Page 101: Instrument Panel
Adding Equipment to Your installed under or on top of the seat fabric, could also interfere with the operation of the passenger Airbag-Equipped Vehicle sensing system. This could either prevent proper deployment of the passenger airbag(s) or prevent Q: Is there anything I might add to or change about the passenger sensing system from properly turning the vehicle that could keep the airbags from off the passenger airbag(s).
Page 102: Restraint System Check
Restraint System Check Airbags The airbag system does not need regularly scheduled Checking the Restraint Systems maintenance or replacement. Make sure the airbag readiness light is working. See Airbag Readiness Light Safety Belts on page 4 30 for more information. Notice: If an airbag covering is damaged, opened, Now and then, check that the safety belt reminder light, or broken, the airbag may not work properly.
Page 103: Replacing Restraint System Parts After A
Replacing Restraint System Parts If the vehicle has the LATCH system and it was being used during a crash, you may need new LATCH system After a Crash parts. New parts and repairs may be necessary even if the WARNING: safety belt or LATCH system (if equipped), was not being used at the time of the crash.
Page 104 NOTES 2-72...
Page 105: Features And Controls
Section 3 Features and Controls Keys ..........3-3 Starting and Operating Your Vehicle .
Page 106 Section 3 Features and Controls Object Detection Systems ..... . . 3-35 Storage Areas ........3-49 Ultrasonic Rear Parking Assist (URPA) .
Page 107: Keys
Keys WARNING: Leaving children in a vehicle with the ignition key is dangerous for many reasons. Children or others could be badly injured or even killed. They could operate the power windows or other controls or even make the vehicle move. The windows will function with the keys in the ignition and children could be seriously injured or killed if caught in the path of a closing window.
Page 108: Remote Keyless Entry (Rke) System
See your dealer if a replacement key or additional key Remote Keyless Entry (RKE) System is needed. Operation Notice: If the keys get locked in the vehicle, it may The Remote Keyless Entry (RKE) transmitter functions have to be damaged to get them out. Always carry a work up to 60 m (195 feet) away from the vehicle.
Page 109 (Lock): Press to lock all the doors. If enabled (Vehicle Locator/Panic Alarm): Press and release through the Driver Information Center (DIC), the parking to locate the vehicle. The turn signal lamps flash and lamps flash once to indicate locking has occurred. the horn sounds three times.
Page 110: Battery Replacement
Programming Transmitters to the Vehicle Only RKE transmitters programmed to the vehicle will work. If a transmitter is lost or stolen, a replacement can be purchased and programmed through your dealer. When the replacement transmitter is programmed to the vehicle, all remaining transmitters must also be programmed.
Page 111: Remote Vehicle Start
Remote Vehicle Start There are other conditions which can affect the performance of the transmitter, see Remote Keyless Your vehicle may have a remote starting feature. Entry (RKE) System on page 3 4 for additional This feature allows you to start the engine from outside information.
Page 112: Remote Start Ready
To manually shut off a remote start: Once two remote starts, or a single remote start with one time extension have been done, the vehicle must Aim the RKE transmitter at the vehicle and press be started with the key. the remote start button until the parking lamps turn off.
Page 113: Doors And Locks
Doors and Locks WARNING: (Continued) Door Locks Outsiders can easily enter through an unlocked door when you slow down or stop WARNING: the vehicle. Locking the doors can help prevent this from happening. Unlocked doors can be dangerous. There are several ways to lock and unlock your vehicle. Passengers, especially children, can easily open the doors and fall out of a moving From the outside, use either the key or the Remote...
Page 114: Delayed Locking
Delayed Locking Programmable Automatic Door Locks This feature allows the driver to delay the actual locking of the doors. When the driver power door lock switch Your vehicle is programmed so that, when the doors are is pressed with the key removed from the ignition, and closed, the ignition is on, and the shift lever is moved the driver door open, a chime will sound three times out of P (Park), all the doors will lock.
Page 115: Rear Door Security Locks
Rear Door Security Locks To open a rear door when the security lock is on, do the following: Rear door security locks prevent passengers from 1. Unlock the door using the Remote Keyless Entry opening the rear doors from the inside. (RKE) transmitter, if the vehicle has one, the The rear door security power door lock switch, or by lifting the rear door...
Page 116: Trunk
Trunk Remote Trunk Release WARNING: Exhaust gases can enter the vehicle if it is driven with the liftgate, trunk/hatch open, or with any objects that pass through the seal between the body and the trunk/hatch or liftgate. Engine exhaust contains Carbon Monoxide (CO) which cannot be seen or smelled.
Page 117: Emergency Trunk Release Handle
Emergency Trunk Release Handle There is a glow-in-the-dark emergency trunk release handle located inside the trunk near the latch. This handle will glow following exposure to light. Pull the release handle to open the trunk from the inside. Rear Seat Pass Through Your vehicle has a small door in the rear seat.
Page 118: Windows
Windows WARNING: Leaving children, helpless adults, or pets in a vehicle with the windows closed is dangerous. They can be overcome by the extreme heat and suffer permanent injuries or even death from heat stroke. Never leave a child, a helpless adult, or a pet alone in a vehicle, especially with the windows closed in warm or hot weather.
Page 119: Power Windows
Power Windows The power window switches are located on the driver's door armrest. WARNING: In addition, each door has a switch for its own window. Leaving children in a vehicle with the keys is dangerous for many reasons. Children or others could be badly injured or even killed.
Page 120: Sun Visors
Express-Down Window Theft-Deterrent Systems This feature is on the front windows. Press the switch This vehicle has theft-deterrent features, however, they to the second position to activate the express-down do not make it impossible to steal. feature. To stop the window as it is lowering, press down briefly on the switch again.
Page 121: Pass-Key Iii+ Electronic Immobilizer
® Arming with the Power Lock Switch PASS-Key III+ Electronic Immobilizer The alarm system will arm when you use either power lock switch to lock the doors while any door is open and See Radio Frequency Statement on page 8 18 the key is removed from the ignition.
Page 122 When trying to start the vehicle if the engine does not To program the new key: start and the security light on the instrument panel 1. Verify that the new key has a stamped on it. cluster comes on, there may be a problem with your theft-deterrent system.
Page 123: Starting And Operating Your Vehicle
Starting and Operating Your Ignition Positions Vehicle The ignition has four different positions: New Vehicle Break-In Notice: The vehicle does not need an elaborate break-in. But it will perform better in the long run if you follow these guidelines: Do not drive at any one constant speed, fast or slow, for the first 500 miles (805 km).
Page 124 This position locks the ignition. It also locks the The steering can bind with the wheels turned off center. transmission and steering column. This is the only If this happens, move the steering wheel from right to position in which the ignition key can be inserted or left while turning the key to ACC/ACCESSORY.
Page 125: Starting Procedure
Retained Accessory Power (RAP) Notice: Do not try to shift to P (Park) if the vehicle is moving. If you do, you could damage the The following accessories can be used for up to transmission. Shift to P (Park) only when the vehicle 10 minutes after the engine is turned off.
Page 126 Engine cranking can be stopped by turning the When the engine starts, let go of the key and ignition switch to the ACC/ACCESSORY or accelerator. If the vehicle starts briefly but then LOCK/OFF position. stops again, repeat these steps. This clears the extra gasoline from the engine.
Page 127: Engine Coolant Heater
Engine Coolant Heater WARNING: The engine coolant heater can provide easier starting and better fuel economy during engine warm up in cold weather conditions at or below 0°F ( 18°C). Vehicles Plugging the cord into an ungrounded outlet could with an engine coolant heater should be plugged in at cause an electrical shock.
Page 128: Automatic Transmission Operation
Automatic Transmission Operation WARNING: It is dangerous to get out of the vehicle if the shift lever is not fully in P (Park) with the parking brake firmly set. The vehicle can roll. Do not leave the vehicle when the engine is running unless you have to.
Page 129 Notice: Shifting to R (Reverse) while the vehicle is Notice: Shifting out of P (Park) or N (Neutral) with moving forward could damage the transmission. the engine running at high speed may damage the The repairs would not be covered by the vehicle transmission.
Page 130: Parking Brake
2 (Second): This position reduces vehicle speed even Parking Brake more than 3 (Third) without using the brakes. You can The parking brake pedal use 2 (Second) on hills. It can help control vehicle is located to the left of the speed as you go down steep mountain roads, but then regular brake pedal, near you would also want to use the brakes off and on.
Page 131: Shifting Into Park
To release the parking brake, hold the regular brake Steering Column Shift Lever pedal down, then push the parking brake pedal down. If the vehicle has a steering column shift lever, use this When you lift your foot off the parking brake pedal, the procedure to shift the vehicle into P (Park): pedal will follow your foot to the released position.
Page 132: Shifting Out Of Park
4. Turn the ignition key to LOCK/OFF. Torque Lock 5. Remove the key and take it with you. If you can Torque lock is when the weight of the vehicle puts too leave the vehicle with the ignition key in your hand, much force on the parking pawl in the transmission.
Page 133: Parking Over Things That Burn
The shift lock is always functional except in the case of 3. Shift out of the P (Park) position to the N (Neutral) a an uncharged or low voltage (less than 9 volt) battery. position. 4. Then, move the shift into the desired gear. If the vehicle has an uncharged battery or a battery with low voltage, try charging or jump starting the battery.
Page 134: Engine Exhaust
Engine Exhaust WARNING: (Continued) WARNING: If unusual fumes are detected or if it is suspected that exhaust is coming into the vehicle: Engine exhaust contains Carbon Monoxide (CO) Drive it only with the windows which cannot be seen or smelled. Exposure to completely down.
Page 135: Mirrors
Mirrors WARNING: (Continued) Automatic Dimming Rearview Mirror death. Never run the engine in an enclosed The vehicle may have an automatic dimming inside area that has no fresh air ventilation. For more ® rearview mirror with OnStar and/or a compass information, see Engine Exhaust on page 3 30.
Page 136: Compass
Compass To adjust for compass variance: 1. Find your current location and variance zone Compass Operation number on the following zone map. There is a compass display in the upper right corner of the mirror. Compass Calibration Press and hold to activate the compass calibration mode.
Page 137: Outside Power Mirrors
3. Once the zone number displays, 2. Press one of the four arrows located on the control pad to move the mirror in the desired direction. press repeatedly until the correct zone number displays. Stop pressing the button and 3. Adjust each outside mirror so that a little of the the mirror returns to normal operation.
Page 138: Park Tilt Mirrors
Side Blind Zone Alert (SBZA) Outside Convex Mirror If the vehicle has the Side Blind Zone Alert (SBZA) system, see Side Blind Zone Alert (SBZA) on WARNING: page 3 36. Park Tilt Mirrors A convex mirror can make things, like other vehicles, look farther away than they really are.
Page 139: Object Detection Systems
Object Detection Systems WARNING: (Continued) Ultrasonic Rear Parking Assist (URPA) If you do not use proper care before and while backing, vehicle damage, injury, or death could For vehicles with the Ultrasonic Rear Parking Assist occur. Even with URPA, always check behind the (URPA) system, it operates at speeds less than 8 km/h vehicle before backing up.
Page 140: Side Blind Zone Alert (Sbza)
A tow bar is attached to the vehicle. The system can be disabled through the Driver Information Center (DIC). See Park Assist under The vehicle's bumper is damaged. Take the vehicle DIC Operation and Displays on page 4 42 for more to your dealer to repair the system.
Page 141 WARNING: (Continued) Failure to use proper care when changing lanes may result in damage to the vehicle, injury, or death. Always check the outside and rearview mirrors, glance over your shoulder, and use the turn signal before changing lanes. When the system detects a vehicle in the side blind zone, amber SBZA displays will light up in the side mirrors.
Page 142 How the System Works SBZA can be disabled through the Driver Information Center (DIC). See Driver Information Center (DIC) on page 4 42 for more information. If the SBZA is disabled by the driver, the SBZA mirror displays will not light up during normal driving.
Page 143 The SBZA displays may remain on if a trailer is SERVICE SIDE BLIND ZONE ALERT SYSTEM: If this attached to the vehicle, or a bicycle or object is message appears, both SBZA displays will remain on extending out to either side of the vehicle. indicating there is a problem with the SBZA system.
Page 144: Lane Departure Warning (Ldw)
Lane Departure Warning (LDW) WARNING: (Continued) The vehicle may have a Lane Departure Warning (LDW) system. Read this entire section before using the system. LDW will indicate the system is working whenever it detects either the left or right lane marking. So if you depart on the side of the lane that LDW is not WARNING: detecting, LDW will not warn you.
Page 145: How The System Works
How the System Works LDW only operates at speeds of 35 mph (56 km) or greater. If LDW is turned on when traveling at these LDW uses a camera located between the inside speeds, the LDW symbol will appear green if the rearview mirror and the windshield to detect the lane system detects a left or right lane marking.
Page 146: Universal Home Remote System
LDW Error Message Universal Home Remote System Operation (With Three Round LED) SERVICE LANE DEPARTURE SYSTEM: This message may appear in the DIC to indicate that LDW is not working properly. If this message remains on after continued driving, the system needs service. Take your vehicle to your dealer.
Page 147 Be sure to keep the original remote control transmitter Programming a garage door opener involves for use in other vehicles, as well as, for future time-sensitive actions, so read the entire procedure programming. Only the original remote control before starting. Otherwise, the device will time out transmitter is needed for Fixed Code programming.
Page 148 3. Immediately return to the vehicle. Press and hold the Universal Home Remote button that will be used to control the garage door until the garage door moves. The indicator light, above the selected button, should slowly blink. This button may need to be held for up to 20 seconds.
Page 149 Most garage door openers sold before 1996 are Fixed the garage door opener motor. If there are a row Code units. of dip switches similar to the graphic above, the garage door opener is a Fixed Code unit. If you Programming a garage door opener involves do not see a row of dip switches, return to the time-sensitive actions, so read the entire procedure...
Page 150 Example of Eight Dip Switches with Two Positions Example of Eight Dip Switches with Three Positions The panel of switches might not appear exactly as they do in the examples above, but they should be similar. The switch positions on the hand-held transmitter could be labeled, as follows: A switch in the up position could be labeled as Up, +, or On.
Page 151 2. Write down the eight to 12 switch settings from left to right as follows: When a switch is in the up position, write Left. When a switch is in the down position, write Right. If a switch is set between the up and down position, write Middle.
Page 152: Reprogramming Universal Home Remote Buttons
5. After entering all of the switch positions, again, Reprogramming Universal Home firmly press and release all three buttons at the Remote Buttons same time. The indicator lights will turn on. Any of the three buttons can be reprogrammed by 6.
Page 153: Storage Areas
Storage Areas Center Console Storage If the vehicle has a full floor console it has two storage Glove Box areas. Lift the left lever located in the front of the armrest lid to access the upper storage tray. Lift the Lift up the glove box handle to open it.
Page 154: Floor Mats
Use only a single floor mat on the driver side. Floor Mats Do not place one floor mat on top of another. The driver side floor mat is held in place by two hooks. WARNING: If a floor mat is the wrong size or is not properly installed, it can interfere with the accelerator pedal and/or brake pedal.
Page 155: Rear Seat Armrest
3. Make sure the floor mat is properly secured and Sunroof verify that it does not interfere with the accelerator or brake pedals. If your vehicle has a power sunroof, the Rear Seat Armrest switches are located on the headliner. This vehicle has a rear seat armrest with cupholders.
Page 156 To close the sunroof, press the front of the driver side switch to the second detent position, and release. To vent the sunroof press and hold the back of the passenger side switch until the vent reaches the desired position. Press the front of the passenger side switch to close the sunroof.
Page 157: Instrument Panel Overview
Section 4 Instrument Panel Instrument Panel Overview ......4-3 Delayed Exit Lighting ......4-13 Hazard Warning Flashers .
Page 158: Audio System(S)
Section 4 Instrument Panel ® StabiliTrak Indicator Light ..... 4-34 Audio System(s) ........4-67 Lane Departure Warning (LDW) Light .
Page 159: Instrument Panel Overview
Instrument Panel Overview Tilt Wheel The tilt lever is located Hazard Warning Flashers on the left side of the steering column. The hazard warning flashers let you warn others that you have a problem. The hazard warning flasher button is located in the center of the instrument panel above the radio.
Page 160: Power Tilt Wheel And Telescopic Steering
Power Tilt Wheel and Telescopic Turn Signal/Multifunction Lever Steering Column For vehicles with a power tilt control, it is located on the left hand side of the steering column. The lever on the left side of the steering column includes the following: To adjust the steering wheel, push the control up, down, : Turn and Lane-Change Signals forward or backward.
Page 161: Turn And Lane-Change Signals
Turn and Lane-Change Signals Turn Signal On Chime If the turn signal is left on, a warning chime sounds and An arrow on the the Driver Information Center (DIC) will display TURN instrument panel cluster SIGNAL ON after driving about a mile as a reminder to flashes in the direction of turn it off.
Page 162: Windshield Wipers
If the headlamps are off or on low beam, the high-beam (Delay): Use to set the delay time between wipe headlamps will turn on. They will stay on as long as you cycles. The wiper speed can be set for a long or short hold the lever toward you and the high-beam indicator delay between wipes.
Page 163: Windshield Washer
Windshield Washer WARNING: WARNING: Cruise control can be dangerous where you cannot drive safely at a steady speed. So, do not In freezing weather, do not use the washer until use the cruise control on winding roads or in the windshield is warmed. Otherwise the washer heavy traffic.
Page 164 Setting Cruise Control The cruise control buttons are located on left side of If the cruise button is on when not in use, it could get the steering wheel. bumped and go into cruise when not desired. Keep the cruise control switch off when cruise is not being used. The cruise control light on the instrument panel cluster comes on after the cruise control has been set to the desired speed.
Page 165 Increasing Speed While Using Cruise Using Cruise Control on Hills Control How well the cruise control will work on hills depends upon the vehicle speed, load and the steepness of the If the cruise control system is already activated, hills. When going up steep hills, you might have to step Press and hold the +RES button on the steering on the accelerator pedal to maintain your speed.
Page 166: Exterior Lamps
Exterior Lamps The exterior lamps control has four positions: (Off): Turn the control to this position to turn off the The exterior lamps exterior lamps. control is located on the AUTO (Automatic): Turn the control to this position to instrument panel to the automatically turn on the headlamps at normal left of the steering wheel.
Page 167: Wiper Activated Headlamps
Wiper Activated Headlamps The DRL system makes the low-beam headlamps turn on at reduced brightness in daylight when the following This feature activates the headlamps and parking lamps conditions are met: after the windshield wipers are turned on and have The engine is running.
Page 168: Fog Lamps
Fog Lamps Exterior Lighting Battery Saver The fog lamps button is on the exterior lamps control to If the exterior lamp button has been left on, the exterior the left of the steering column. lamps will turn off about 10 minutes after the ignition is turned to LOCK/OFF and a door has been opened.
Page 169: Courtesy Lamps
Courtesy Lamps Theater Dimming When any door is opened, several lamps turn on This feature allows for a three to five second fade out of making it easier for you to enter and exit the vehicle. the courtesy lamps instead of immediate turn off. Turn the instrument panel brightness control completely Delayed Exit Lighting clockwise to manually turn on these lamps.
Page 170: Electric Power Management
Electric Power Management EPM works to prevent excessive discharge of the battery. It does this by balancing the generator's output The vehicle has Electric Power Management (EPM) that and the vehicle's electrical needs. It can increase estimates the battery's temperature and state of charge. engine idle speed to generate more power, whenever It then adjusts the voltage for best performance and needed.
Page 171: Battery Run-Down Protection
Battery Run-Down Protection Remove the cover to access and replace when not in use. This feature helps prevent the battery from being drained, if the interior courtesy lamps, WARNING: reading/map lamps, visor vanity lamps or trunk lamp are accidentally left on. If any of these lamps are left on, they automatically turn off after 10 minutes, Power is always supplied to the outlets.
Page 172: Ashtray(S)
When adding electrical equipment, be sure to follow Climate Controls the proper installation instructions included with the equipment. See Add-On Electrical Equipment on Climate Control System page 6 107. The heating, cooling, and ventilation for the vehicle can Notice: Hanging heavy equipment from the power be controlled with this system.
Page 173 (Fan Control): Turn clockwise or counterclockwise to increase or decrease the fan speed. The fan speed is temporarily reduced between the transition to a new mode. The fan will resume when the new mode is complete. If the airflow seems low when the fan speed is at the highest setting, the passenger compartment air filter may need to be replaced.
Page 174 For quicker cool down on hot days, do the following: (Floor/Defog): This clears the windows of fog or moisture. Air is directed to the windshield and side 1. Select window outlets and to the floor outlets. The system runs the air conditioning compressor unless the outside 2.
Page 175: Rear Window Defogger
Rear Window Defogger If the vehicle has heated outside rearview mirrors, the mirrors heat to help clear fog or frost from the surface The rear window defogger uses a warming grid to of the mirror when the rear window defogger is on. remove fog from the rear window.
Page 176: Dual Automatic Climate Control System
Dual Automatic Climate Control System The heating, cooling, and ventilation for the vehicle can be controlled with this system. For vehicles with the remote start feature and it is activated, the climate control system heats or cools the inside of the vehicle, with the settings used before the vehicle was turned off.
Page 177 AUTO (Automatic Mode) When the ENG/MET (English/metric) button on the Driver Information Center (DIC) is pressed, the display 1. Turn the fan control to AUTO. shows readings in Fahrenheit or Celsius. Use the 2. Turn the mode control to AUTO. ENG/MET button to toggle between the readings.
Page 178: Manual Operation
Manual Operation To change the current mode, select one of the following: (Vent): Air is directed to the instrument panel outlets. (Off): Turns the climate control system off. Outside air still enters the vehicle and is directed to the floor. (Bi-Level): Air is divided between the instrument The airflow direction and temperature can be adjusted.
Page 179 When the passenger climate control system is on, the (Air Conditioning): Press to turn the air passenger temperature setting is displayed. conditioning system on or off and override the automatic system. An indicator light below the If the PASS button is pressed to turn the passenger button comes on to show that this mode is on.
Page 180 There is also an interior temperature sensor located Rear Window Defogger next to the steering wheel that measures the The rear window defogger uses a warming grid to temperature of the air inside the vehicle. remove fog or frost from the rear window. There is also an exterior temperature sensor located <...
Page 181: Outlet Adjustment
Outlet Adjustment The access panel for the passenger compartment air filter is located under the hood near the windshield, on Use the levers, located in the middle of the front the passenger's side of the vehicle. outlets, to change the direction of the airflow. Use the To access the passenger compartment air filter, do the thumbwheel located between the outlets to turn them on following:...
Page 182 3. To remove the air filter, insert a tool between the 4. Insert the new air filter by pushing until you hear a air filter and the compartment wall on the outboard click. Reinstall the push pin and snap the cover side of the vehicle.
Page 183: Warning Lights, Gauges, And Indicators
Warning Lights, Gauges, and Gauges can indicate when there might be or there is a problem with one of the vehicle's functions. Often Indicators gauges and warning lights work together to indicate a problem with the vehicle. Warning lights and gauges can signal that something is When one of the warning lights comes on and stays on wrong before it becomes serious enough to cause an while driving, or when one of the gauges shows there...
Page 184: Instrument Panel Cluster
Instrument Panel Cluster English Super Model Shown, Metric and Base Similar 4-28...
Page 185: Speedometer And Odometer
Speedometer and Odometer Safety Belt Reminders The speedometer shows the vehicle speed in both Driver Safety Belt Reminder Light miles per hour (mph) and kilometers per hour (km/h). When the engine is started, a chime sounds for several The odometer shows how far the vehicle has been seconds to remind a driver to fasten the safety belt, driven, in either miles or kilometers.
Page 186: Airbag Readiness Light
Passenger Safety Belt Reminder Light Airbag Readiness Light For vehicles equipped with the passenger safety belt The system checks the airbag's electrical system for reminder light, several seconds after the engine is possible malfunctions. If the light stays on it indicates started, a chime sounds for several seconds to remind there is an electrical problem.
Page 187: Passenger Airbag Status Indicator
If there is a problem with the airbag system, an airbag If you are using remote start to start the vehicle from Driver Information Center (DIC) message can also a distance, if equipped, you may not see the system come on. See DIC Warnings and Messages on check.
Page 188: Charging System Light
If, after several seconds, both status indicator lights If it does not, have the vehicle serviced by your dealer. remain on, or if there are no lights at all, there may be a The light should go out once the engine starts. If it stays problem with the lights or the passenger sensing on, or comes on while driving, there could be a problem system.
Page 189: Antilock Brake System (Abs) Warning Light
If the light comes on while driving, pull off the road and stop carefully. The pedal can be harder to push, or the pedal could go closer to the floor. It could take longer to stop. Try turning off and restarting the vehicle one or two times, if the light is still on, have the vehicle towed for service.
Page 190: Traction Control System (Tcs) Warning
If the regular brake system warning light is also on, the If it stays on or comes on while driving a SERVICE vehicle does not have antilock brakes and there is a TRACTION CONTROL message appears in the Driver problem with the regular brakes. See Brake System Information Center (DIC).
Page 191: Lane Departure Warning (Ldw) Light
This light may come on while the vehicle is first driven Lane Departure Warning (LDW) Light and the STABILITRAK NOT READY message will For vehicles with the appear in the Driver Information Center (DIC). See ® lane departure warning StabiliTrak System on page 5 5 for more system, this light briefly information.
Page 192: Engine Coolant Temperature Warning Light
Engine Coolant Temperature Engine Coolant Temperature Gauge Warning Light This light comes on briefly while starting the vehicle. If it does not, have the vehicle serviced by the dealer. If the system is working normally the indicator light English Metric goes off.
Page 193: Tire Pressure Light
Tire Pressure Light When the Light Flashes First and Then is On Steady For vehicles with a Tire This indicates that there may be a problem with the Tire Pressure Monitoring Pressure Monitor System. The light flashes for about a System, this light comes minute and stays on steady for the remainder of the on briefly when the engine...
Page 194 Malfunctions often are indicated by the system before To prevent more serious damage to the vehicle: any problem is apparent. Being aware of the light can Reduce vehicle speed. prevent more serious damage to the vehicle. This Avoid hard accelerations. system assists the service technician in correctly diagnosing any malfunction.
Page 195: Emissions Inspection And Maintenance Programs
Make sure the electrical system is not wet. The system could be wet if the vehicle was driven through a deep puddle of water. Make sure to fuel the vehicle with quality fuel. Poor fuel quality causes the engine not to run as efficiently as designed and can cause: stalling after start-up, stalling when the vehicle is changed into gear, misfiring, hesitation on acceleration,...
Page 196: Maintenance Schedule
Oil Pressure Light If the light comes on and stays on, it means that oil is not flowing through the engine properly. The vehicle could be low on oil and it might have some other system problem. Security Light For information regarding this light and the vehicle's security system, see Content Theft-Deterrent...
Page 197: Cruise Control Light
Cruise Control Light Fuel Gauge The cruise control light comes on whenever the cruise control is set. English Metric The light goes out when the cruise control is turned off. See Cruise Control on page 4 7 for more information. The fuel gauge shows about how much fuel is in the tank.
Page 198: Driver Information Center (Dic)
Here are some things that some owners ask about. The DIC displays trip, fuel, and vehicle system None of these show a problem with the fuel gauge: information, and warning messages if a system problem is detected. The bottom line of the DIC At the service station, the gas pump shuts off shows the shift lever position indicator.
Page 199 DIC Buttons Trip/Fuel Menu Items The buttons are the trip/fuel, vehicle information, (Trip/Fuel): Press this button to scroll through the customization, and set/reset buttons. The button following menu items: functions are detailed in the following pages. Odometer Press the trip/fuel button until ODOMETER displays. This display shows the distance the vehicle has been driven in either kilometers (km) or miles (mi).
Page 200 To use the retro-active reset feature, press and hold This is because different driving conditions produce the set/reset button for at least four seconds. The trip different fuel economies. Generally, freeway driving odometer will display the number of kilometers (km) or produces better fuel economy than city driving.
Page 201: Maintenance Schedule
Average Speed When the remaining oil life is low, the CHANGE ENGINE OIL SOON message will appear on the Press the trip/fuel button until AVERAGE SPEED display. See CHANGE ENGINE OIL SOON under DIC displays. This display shows the average speed of Warnings and Messages on page 4 49.
Page 202: Park Assist
Park Assist Tire Pressure If your vehicle has the Ultrasonic Rear Parking Assist On vehicles with the Tire Pressure Monitor System (URPA) system, this display allows the system to be (TPMS), the pressure for each tire can be viewed in the turned on or off.
Page 203: Dic Compass
Calibrate Compass Compass Zone Your vehicle may have this feature. The compass can Your dealer will set the correct zone for your location. be manually calibrated. To calibrate the compass If the zone is not set to your location or you drive out through the DIC, see DIC Compass on page 4 47.
Page 204 Compass Calibration The compass can be manually calibrated. Only calibrate the compass in a magnetically clean and safe location, such as an open parking lot, where driving the vehicle in circles is not a danger. It is suggested to calibrate away from tall buildings, utility wires, manhole covers, or other industrial structures, if possible.
Page 205: Dic Warnings And Messages
2. Press the vehicle information button until the messages disappear, not correct the problem. The following are the possible messages that can be PRESS TO CALIBRATE COMPASS displays. displayed and some information about them. 3. Press the set/reset button to start the compass AUTOMATIC LIGHT CONTROL OFF calibration.
Page 206: Engine Overheated Stop Engine
CHANGE ENGINE OIL SOON ENGINE OVERHEATED IDLE ENGINE This message displays when service is required for the Notice: If you drive your vehicle while the engine is vehicle. See your dealer. See Engine Oil on page 6 18 overheating, severe engine damage may occur. If an and Scheduled Maintenance on page 7 3 for more overheat warning appears on the instrument panel information.
Page 207: Fuel Level Low
ENGINE POWER IS REDUCED ICE POSSIBLE DRIVE WITH CARE This message displays when the vehicle's engine This message displays when the outside air power is reduced. Reduced engine power can affect the temperature is cold enough to create icy road vehicle's ability to accelerate.
Page 208: Oil Pressure Low Stop Engine
OIL PRESSURE LOW STOP ENGINE PASSENGER DOOR OPEN Notice: If you drive your vehicle while the engine This message displays when the front passenger door oil pressure is low, severe engine damage may is not closed properly. Make sure that the door is closed occur.
Page 209: Service Air Bag
SERVICE A/C (Air Conditioning) SERVICE BRAKE ASSIST SYSTEM This message displays if there is a problem with the brake system. The brake system warning light and This message displays when the electronic sensors the antilock brake system warning light may also be that control the air conditioning and heating systems displayed on the instrument panel cluster.
Page 210 SERVICE LANE DEPARTURE SYSTEM SERVICE SIDE BLIND ZONE ALERT SYSTEM If your vehicle has the Lane Departure Warning (LDW) system, this message may display to indicate that the If your vehicle has the Side Blind Zone Alert (SBZA) LDW system is not working properly. If this message system and this message displays, both SBZA displays remains on after continued driving, the system needs will remain on indicating there is a problem with the...
Page 211: Service Suspension System
SERVICE SUSPENSION SYSTEM SERVICE TRACTION CONTROL This message displays to indicate that the suspension This message displays when the Traction Control system is not operating properly. See your dealer for System (TCS) is not functioning properly. A warning service. light also appears on the instrument panel cluster. See Traction Control System (TCS) Warning Light on SERVICE THEFT SYSTEM page 4 34.
Page 212: Theft Attempted
SIDE BLIND ZONE SYS. UNAVAILABLE STARTING DISABLED SERVICE THROTTLE If your vehicle has the Side Blind Zone Alert (SBZA) system, this message displays when the SBZA system This message displays if the starting of the engine is is disabled because the sensor is blocked and cannot disabled due to the electronic throttle control system.
Page 213 TIRE LEARNING ACTIVE TRACTION CONTROL OFF On vehicles with the Tire Pressure Monitor System This message displays when the Traction Control (TPMS), this message displays when the TPMS is System (TCS) is turned off. Adjust your driving re-learning the tire positions on your vehicle. The tire accordingly.
Page 214: Trunk Open
TRUNK OPEN DIC Vehicle Customization This message displays when the trunk is not closed Your vehicle has customization capabilities that allow completely. Make sure that the trunk is closed you to program certain features to one preferred setting. completely. See Trunk on page 3 12. Customization features can only be programmed to one setting on the vehicle and cannot be programmed TURN SIGNAL ON...
Page 215 Entering the Feature Settings Menu DISPLAY LANGUAGE 1. Turn the ignition on and place the vehicle in This feature allows you to select the language in which the DIC messages will appear. P (Park). To avoid excessive drain on the battery, it is Press the customization button until the DISPLAY recommended that the headlamps are turned off.
Page 216: Auto Door Unlock
Press the customization button until AUTO DOOR Press the customization button until AUTO DOOR LOCK appears on the DIC display. Press the set/reset UNLOCK appears on the DIC display. Press the button once to access the settings for this feature. Then set/reset button once to access the settings for this press the customization button to scroll through the feature.
Page 217: Remote Door Lock
REMOTE DOOR LOCK NO CHANGE: No change will be made to this feature. The current setting will remain. This feature allows you to select the type of feedback To select a setting, press the set/reset button while the you will receive when locking the vehicle with the desired setting is displayed on the DIC.
Page 218: Exit Lighting
DELAY DOOR LOCK EXIT LIGHTING This feature allows you to select whether or not the This feature allows you to select the amount of time you locking of the vehicle's doors will be delayed. When want the exterior lamps to remain on when it is dark locking the doors with the power door lock switch and a enough outside.
Page 219: Approach Lighting
APPROACH LIGHTING CHIME VOLUME This feature allows you to select whether or not to have This feature allows you to select the volume level of the the exterior lights turn on briefly during low light periods chime. after unlocking the vehicle using the Remote Keyless Press the customization button until CHIME VOLUME Entry (RKE) transmitter.
Page 220 Press the customization button until PARK TILT Press the customization button until EASY EXIT MIRRORS appears on the DIC display. Press the RECALL appears on the DIC display. Press the set/reset button once to access the settings for this set/reset button once to access the settings for this feature.
Page 221 EASY EXIT SETUP NO CHANGE: No change will be made to this feature. The current setting will remain. If your vehicle has this feature, it allows you to select To select a setting, press the set/reset button while the which areas will recall with the automatic easy exit desired setting is displayed on the DIC.
Page 222: Factory Settings
NO CHANGE: No change will be made to this feature. FACTORY SETTINGS The current setting will remain. This feature allows you to set all of the customization To select a setting, press the set/reset button while the features back to their factory default settings. desired setting is displayed on the DIC.
Page 223: Audio System(S)
Exiting the Feature Settings Menu This system provides access to many audio and non audio listings. The feature settings menu will be exited when any of To minimize taking your eyes off the road while driving, the following occurs: do the following while the vehicle is parked: The vehicle is shifted out of P (Park).
Page 224: Setting The Clock
Setting the Clock The date does not automatically display. To see the date press while the radio is on. The date with To set the time and date: display times out after a few seconds and goes back to 1. Turn the ignition key to ACC/ACCESSORY or the normal radio and time display.
Page 225: Radio(S)
Radio(s) incorrect information that causes the radio features to work improperly. If this happens, contact the radio station. Playing the Radio (Power/Volume): Press to turn the system on and off. Turn to increase or decrease the volume. Speed Compensated Volume (SCV): Radios with the Speed Compensated Volume (SCV) feature automatically adjust the radio volume to compensate for road and wind noise as the vehicle speeds up or...
Page 226: Finding A Station
Finding a Station (Information): For vehicles with XM, MP3, WMA, or RDS features, press to display additional text BAND: Press to choose between FM, AM, or XM information related to the current FM-RDS or XM (if equipped). station; or CD, MP3, WMA song. Song title information (Tune): Turn to select radio stations.
Page 227: Storing A Radio Station
¨ FAV (Favorites): A maximum of 36 stations can be SEEK: Press to seek or scan stations with a strong stored as favorites using the six softkeys located below signal in the selected band. the radio station frequency tabs and by using the radio ¨...
Page 228: Adjusting The Speakers (Balance/Fade)
To store a station as a favorite: The radio may also be capable of adjusting all tone and speaker controls to the middle position by pressing 1. Tune to the desired radio station. knob for more than two seconds until the radio 2.
Page 229 The radio may be capable of adjusting balance or fade 4. To go to the previous or to the next XM station to the middle position by pressing the softkey below the within the selected category, do one of the BAL or FADE tab for more than two seconds.
Page 230: Loading A Cd
Removed categories can be restored by pressing the For more information, contact XM at www.xmradio.com softkey under the Add tab when a removed category or call 1-800-929-2100 in the U.S. and www.xmradio.ca displays or by pressing the softkey below the Restore or call 1-877-438-9677 in Canada.
Page 231: Playing A Cd
Playing a CD To use random: 1. Press the softkey below RDM tab until Random If the ignition or radio is turned off with a CD in the Current Disc displays. player, the CD stays in the player. When the ignition or radio is turned on, the CD starts to play where it 2.
Page 232: Care Of Cds
CD Messages Care of CDs CHECK DISC: If an error message displays and/or the Store CD(s) in their original cases or other protective CD comes out, it could be for one of the following cases and away from direct sunlight and dust. The CD reasons: player scans the bottom of the disc.
Page 233: Using The Auxiliary Input Jack
Notice: If a label is added to a CD, more than one To use a portable audio player, connect a 3.5 mm CD is inserted into the slot at a time, or an attempt (1/8 in) cable to the radio's front auxiliary input jack. is made to play scratched or damaged CDs, the When a device is connected, press the radio CD/AUX CD player could be damaged.
Page 234: Using An Mp3
USB Support Using an MP3 The USB connector is located on the front of the radio Format and uses the USB 2.0 standard. Radios that have the capability of playing MP3's can USB Supported Devices play .mp3 files that were recorded onto a CD-R or CD-RW disc.
Page 235 USB Supported File and Folder Structure Order of Play The radio supports: Tracks are played in the following order: Up to 700 folders. Play begins from the first track in the first playlist and continues sequentially through all tracks in Up to 8 folders in depth.
Page 236 Preprogrammed Playlists FWD (Fast Forward): Press and hold to advance playback quickly. Sound is heard at a CDs that have preprogrammed playlists that were reduced volume and the elapsed time of the file created using WinAmp , MusicMatch , or Real displays.
Page 237: Connecting A Usb Storage Device ® Or Ipod
When the scan is finished, the disc begins playing files Connecting a USB Storage Device in order by artist. The current artist playing is shown on ® or iPod the second line of the display. Once all songs by that artist are played, the player moves to the next artist in The USB Port can be used to control an iPod or a USB alphabetical order and begins playing files by that artist.
Page 238: Using Softkeys To Control A Usb Storage Device Or Ipod
Using the Radio to Control a USB Using Softkeys to Control a USB Storage Device or iPod Storage Device or iPod The radio can control a USB storage device or an iPod The five softkeys below the radio display are used to using the radio buttons and knobs and display song control the functions listed below.
Page 239 Genres 3. Press to select the desired folder. If there is Songs more then one folder, repeat Steps 1 and 2 until the desired folder is reached. Composers 4. Turn to scroll through the files in the selected To select files: folder.
Page 240: Xm Radio Messages
Repeat Functionality (Shuffle Album): Press the softkey below shuffle all songs in the current album on an iPod. To use Repeat: (Shuffle Folder): Press the softkey below Press the softkey below to select between shuffle all songs in the current folder on a USB storage Repeat All and Repeat Track.
Page 241: Navigation/Radio System
Channel Unavail: This previously assigned channel XM Radio ID: If tuned to channel 0, this message is no longer assigned. Tune to another station. If this alternates with the XM Radio 8 digit radio ID label. station was one of the presets, choose another station This label is needed to activate the service.
Page 242: Bluetooth
® Bluetooth WARNING: For vehicles equipped with Bluetooth capability, the system can interact with many cell phones, allowing: When using a cell phone, it can be distracting to Placement and receipt of calls in a look too long or too often at the screen of the hands-free mode.
Page 243: Voice Recognition
Voice Recognition Bluetooth Controls The Bluetooth system uses voice recognition to Use the buttons located on the steering wheel to interpret voice commands to dial phone numbers and operate the in vehicle Bluetooth system. See Audio name tags. Steering Wheel Controls on page 4 94 for more information.
Page 244: Pairing A Phone
Pairing Information 4. Start the pairing process on the cell phone that you want to pair. For help with this process, see your Up to five cell phones can be paired to the cell phone manufacturers user guide. Bluetooth system. 5.
Page 245: Storing And Deleting Phone Numbers
Deleting a Paired Phone Storing and Deleting Phone Numbers If the phone name you want to delete is unknown, see The system can store up to 30 phone numbers as name Listing All Paired and Connected Phones. tags in the Hands Free Directory that is shared between the Bluetooth and OnStar systems.
Page 246 Using the Digit Store Command Using the Delete All Name Tags Command If an unwanted number is recognized by the system, say Clear at any time to clear the last number. This command deletes all stored name tags in the Hands Free Calling Directory and the OnStarTurn by To hear all of the numbers recognized by the system, Turn Destinations Directory.
Page 247: Making A Call
Making a Call To hear all of the numbers recognized by the system, say Verify at any time. Calls can be made using the following commands. 1. Press and hold for two seconds. Dial or Call: The dial or call command can be used 2.
Page 248: Call Waiting
Call Waiting Muting a Call Call waiting must be supported on the cell phone and During a call, all sounds from inside the vehicle can be enabled by the wireless service carrier. muted so that the person on the other end of the call cannot hear them.
Page 249 To Transfer Audio to the Bluetooth System Dual Tone Multi-Frequency (DTMF) From a Cell Phone Tones During a call with the audio on the cell phone, The Bluetooth system can send numbers and the press . The audio transfers to the vehicle. If the numbers stored as name tags during a call.
Page 250: Other Information
Other Information Audio Steering Wheel Controls ® The Bluetooth word mark and logos are owned by the Vehicles with audio ® Bluetooth SIG, Inc. and any use of such marks by steering wheel controls General Motors is under license. Other trademarks and could differ depending trade names are those of their respective owners.
Page 251 CD/DVD 3. Press and release to scroll up or down the list. To select tracks on a CD/DVD: To select a folder, press and hold , or Press and release to go to the next or ¨ press when the folder is highlighted. previous track.
Page 252 Navigating an iPod or USB Device on the ¨ (Seek): Press to go to the next radio station while in Music Navigator Screen (Vehicles with a AM, FM, or XM . Navigation System) For vehicles with or without a navigation system: ¨...
Page 253: Radio Reception
Radio Reception Satellite Radio Service XM Satellite Radio Service gives digital radio reception Frequency interference and static can occur during from coast-to-coast in the 48 contiguous United States, normal radio reception if items such as cell phone and in Canada. Just as with FM, tall buildings or hills chargers, vehicle convenience accessories, and can interfere with satellite radio signals, causing the external electronic devices are plugged into the...
Page 254: Xm Satellite Radio Antenna System
If a cellular telephone antenna needs to be attached to Satellite Radio Antenna the glass, make sure that the grid lines for the AM-FM System antenna are not damaged. There is enough space between the grid lines to attach a cellular telephone The XM Satellite Radio antenna is located on the roof of antenna without interfering with radio reception.
Page 255: Driving Your Vehicle
Section 5 Driving Your Vehicle Your Driving, the Road, and the Vehicle ..5-2 Driving in Rain and on Wet Roads ... . . 5-12 Defensive Driving .
Page 256: Your Driving, The Road, And The Vehicle
Your Driving, the Road, and the Drunk Driving Vehicle WARNING: Defensive Driving Drinking and then driving is very dangerous. Defensive driving means always expect the Your reflexes, perceptions, attentiveness, and unexpected. The first step in driving defensively judgment can be affected by even a small amount is to wear the safety belt.
Page 257: Control Of A Vehicle
For persons under 21, it is against the law in every Braking U.S. state to drink alcohol. There are good medical, See Brake System Warning Light on page 4 32. psychological, and developmental reasons for these laws. Braking action involves perception time and reaction time.
Page 258: Antilock Brake System (Abs)
Avoid needless heavy braking. Some people drive in Antilock Brake System (ABS) spurts, heavy acceleration followed by heavy braking, This vehicle has the Antilock Brake System (ABS), an rather than keeping pace with traffic. This is a mistake. advanced electronic braking system that helps prevent The brakes might not have time to cool between hard a braking skid.
Page 259: Brake Assist
ABS can change the brake pressure to each wheel, as Brake Assist required, faster than any driver could. This can help the This vehicle has a Brake Assist feature designed to driver steer around the obstacle while braking hard. assist the driver in stopping or decreasing vehicle As the brakes are applied, the computer keeps speed in emergency driving conditions.
Page 260: Traction Control System (Tcs)
Traction Control System (TCS) This light will flash when the system is operating. The vehicle has a Traction Control System (TCS) that limits wheel spin. This is especially useful in slippery road conditions. The system operates only if it senses that the front wheels are spinning too much or beginning to lose traction.
Page 261: Magnetic Ride Control
The SERVICE TRACTION CONTROL message in the a result of the brake-traction control working. If the DIC and the TCS/StabiliTrak warning light comes on if controller detects excessive wheel spin in this mode, there is a problem with the traction control system. See the TCS/StabiliTrak light may blink.
Page 262: Steering
Steering Steering in Emergencies There are times when steering can be more effective Power Steering than braking. For example, you come over a hill and If power steering assist is lost because the engine stops find a truck stopped in your lane, or a car suddenly pulls or the system is not functioning, the vehicle can be out from nowhere, or a child darts out from between steered but it will take more effort.
Page 263: Off-Road Recovery
Off-Road Recovery The vehicle's right wheels can drop off the edge of a road onto the shoulder while driving. An emergency like this requires close attention and a quick decision. If holding the steering wheel at the recommended 9 and 3 o'clock positions, it can be turned a full 180 degrees very quickly without removing either hand.
Page 264: Passing
Passing Skidding In a skid, a driver can lose control of the vehicle. Passing another vehicle on a two-lane road can be Defensive drivers avoid most skids by taking dangerous. To reduce the risk of danger while passing: reasonable care suited to existing conditions, and by Look down the road, to the sides, and to not overdriving those conditions.
Page 265: Driving At Night
Slow down and keep more space between you and While driving on a surface with reduced traction, try other vehicles because headlamps can only light your best to avoid sudden steering, acceleration, up so much road ahead. or braking, including reducing vehicle speed by shifting to a lower gear.
Page 266: Driving In Rain And On Wet Roads
Driving in Rain and on Wet Roads Hydroplaning Hydroplaning is dangerous. Water can build up under Rain and wet roads can reduce vehicle traction and your vehicle's tires so they actually ride on the water. affect your ability to stop and accelerate. Always drive This can happen if the road is wet enough and you are slower in these types of driving conditions and avoid going fast enough.
Page 267: Before Leaving On A Long Trip
Before Leaving on a Long Trip Highway Hypnosis To prepare your vehicle for a long trip, consider having Always be alert and pay attention to your surroundings it serviced by your dealer before departing. while driving. If you become tired or sleepy, find a safe place to park your vehicle and rest.
Page 268: Hill And Mountain Roads
Hill and Mountain Roads WARNING: Driving on steep hills or through mountains is different than driving on flat or rolling terrain. Tips for driving in these conditions include: Coasting downhill in N (Neutral) or with the ignition off is dangerous. The brakes will have to Keep the vehicle serviced and in good shape.
Page 269: Winter Driving
Winter Driving The Traction Control System (TCS) on page 5 6 improves the ability to accelerate on slippery roads, Driving on Snow or Ice but slow down and adjust your driving to the road conditions. When driving through deep snow, turn off Drive carefully when there is snow or ice between the the traction control system to help maintain vehicle tires and the road, creating less traction or grip.
Page 270 Blizzard Conditions WARNING: (Continued) Being stuck in snow can be a serious situation. Stay with the vehicle unless there is help nearby. If possible, use the Roadside Assistance Program on page 8 7. Open a window about 5 cm (2 in) on the side To get help and keep everyone in the vehicle safe: of the vehicle that is away from the wind to bring in fresh air.
Page 271: Rocking Your Vehicle To Get It Out
To save fuel, run the engine for only short periods as needed to warm the vehicle and then shut the engine WARNING: off and close the window most of the way to save heat. Repeat this until help arrives but only when you feel If the vehicle's tires spin at high speed, they can really uncomfortable from the cold.
Page 272: Loading The Vehicle
Loading the Vehicle Tire and Loading Information Label It is very important to know how much weight your vehicle can carry. Two labels on your vehicle show how much weight it may properly carry, the Tire and Loading Information label and the Vehicle Certification label.
Page 273 The Tire and Loading Information label also lists The resulting figure equals the available the tire size of the original equipment tires (C) and amount of cargo and luggage load capacity. the recommended cold tire inflation pressures (D). For example, if the XXX amount equals For more information on tires and inflation, see 1400 lbs and there will be five 150 lb Tires on page 6 57 and Inflation - Tire Pressure on...
Page 274 Example 1 Example 2 Item Description Total Item Description Total Maximum Vehicle Maximum Vehicle 1,000 lbs 1,000 lbs Capacity Weight for Capacity Weight for (453 kg) (453 kg) Example 1 = Example 2 = Subtract Occupant Subtract Occupant Weight @ 150 lbs 300 lbs (136 kg) Weight @ 150 lbs 750 lbs (340 kg)
Page 275 and seating positions. The combined weight of the driver, passengers, and cargo should never exceed your vehicle's maximum vehicle capacity weight. Certification Label Example 3 Item Description Total Maximum Vehicle 1,000 lbs Capacity Weight for (453 kg) Example 3 = Subtract Occupant 1,000 lbs Weight @ 200 lbs...
Page 276 Never exceed the GVWR for your vehicle or the WARNING: Gross Axle Weight Rating (GAWR) for either the front or rear axle. If there is a heavy load, it should be spread out. Things inside the vehicle can strike and injure people in a sudden stop or turn, or in a crash.
Page 277: Towing
Towing Here are some important things to consider before recreational vehicle towing: What's the towing capacity of the towing vehicle? Towing Your Vehicle Be sure to read the tow vehicle manufacturer's To avoid damage, the disabled vehicle should be towed recommendations.
Page 278: Dinghy Towing
Dinghy Towing Dolly Towing The vehicle can be towed using a dolly. To tow the If the vehicle is towed with all four wheels vehicle using a dolly, follow these steps: on the ground, the drivetrain components could be damaged. The repairs would not be covered by the 1.
Page 279: Towing A Trailer
5. Remove the key from the ignition. The vehicle can tow a trailer if it is equipped with the proper trailer towing equipment. To identify the 6. Secure the vehicle to the dolly. trailering capacity of the vehicle, read the information 7.
Page 280: Pulling A Trailer
Pulling A Trailer Three important considerations have to do with weight: the weight of the trailer, Here are some important points: the weight of the trailer tongue There are many different laws, including speed limit restrictions, having to do with trailering. Make and the total weight on the vehicle's tires.
Page 281: Weight Of The Trailer Tongue
Weight of the Trailer Tongue The tongue load (A) of any trailer is an important weight to measure because it affects the total gross weight of the vehicle. The Gross Vehicle Weight (GVW) includes the curb weight of the vehicle, any cargo carried in it, and the people who will be riding in the vehicle.
Page 282: Safety Chains
Hitches Safety Chains It is important to have the correct hitch equipment. Always attach chains between the vehicle and the Crosswinds, large trucks going by and rough roads are trailer. Cross the safety chains under the tongue of the a few reasons why the right hitch is needed. Here are trailer to help prevent the tongue from contacting the some rules to follow: road if it becomes separated from the hitch.
Page 283: Driving With A Trailer
Driving with a Trailer Passing Towing a trailer requires a certain amount of More passing distance is needed when towing a trailer. experience. Get to know the rig before setting out for Because the rig is longer, it is necessary to go much the open road.
Page 284: Turn Signals When Towing A Trailer
Turn Signals When Towing a Trailer Parking on Hills The arrows on the instrument panel flash whenever signaling a turn or lane change. Properly hooked up, WARNING: the trailer lamps also flash, telling other drivers the vehicle is turning, changing lanes or stopping. Parking the vehicle on a hill with the trailer When towing a trailer, the arrows on the instrument attached can be dangerous.
Page 285: Engine Cooling When Trailer Towing
Leaving After Parking on a Hill Engine Cooling When Trailer Towing 1. Apply and hold the brake pedal while you: The cooling system may temporarily overheat during severe operating conditions. See Engine Overheating start the engine, on page 6 35. shift into a gear, and Changing a Tire When Trailer Towing release the parking brake.
Page 286 NOTES 5-32...
Page 287: Service And Appearance Care
Section 6 Service and Appearance Care Service ..........6-3 Engine Coolant (4.6L Engine) .
Page 288 Section 6 Service and Appearance Care Tire Inspection and Rotation ....6-70 Weatherstrips ....... . 6-101 When It Is Time for New Tires .
Page 289: Service
Service Accessories and Modifications When non dealer accessories are added to the For service and parts needs, visit your dealer. You vehicle, they can affect vehicle performance and safety, will receive genuine GM parts and GM-trained and including such things as airbags, braking, stability, supported service people.
Page 290: California Proposition 65 Warning
California Proposition 65 Warning Doing Your Own Service Work Most motor vehicles, including this one, contain and/or emit chemicals known to the State of California to WARNING: cause cancer and birth defects or other reproductive harm. Engine exhaust, many parts and systems, many fluids, and some component wear by-products contain You can be injured and the vehicle could be and/or emit these chemicals.
Page 291: Adding Equipment To The Outside Of The
Keep a record with all parts receipts and list the mileage and the date of any service work performed. See Maintenance Record on page 7 12. Adding Equipment to the Outside of the Vehicle Things added to the outside of the vehicle can affect the airflow around it.
Page 292: Gasoline Octane
Gasoline Octane Gasoline Specifications (U.S. and Canada Only) If the vehicle has the 3.9L V6 engine (VIN Code M), use regular unleaded gasoline with a posted octane rating At a minimum, gasoline should meet ASTM of 87 or higher. If the octane rating is less than 87, an specification D 4814 in the United States or audible knocking noise, commonly referred to as spark CAN/CGSB 3.5 or 3.511 in Canada.
Page 293: Additives
Additives Notice: This vehicle was not designed for fuel that contains methanol. Do not use fuel containing To provide cleaner air, all gasolines in the United States methanol. It can corrode metal parts in the fuel are now required to contain additives that help prevent system and also damage plastic and rubber parts.
Page 294 Many service stations will not have an 85% ethanol If you do switch fuels, it is recommended that you add fuel (E85) pump available. The U.S. Department as much fuel as possible do not add less than 11 L of Energy has an alternative fuels website (3 gal) when refueling.
Page 295: Fuels In Foreign Countries
Fuels in Foreign Countries Never use leaded gasoline or any other fuel not recommended in the previous text on fuel. Costly repairs caused by use of improper fuel would not be covered by the vehicle warranty. To check the fuel availability, ask an auto club, or contact a major oil company that does business in the country where you will be driving.
Page 296 While refueling, hang the tethered fuel cap from the The TIGHTEN GAS CAP message displays on the hook on the fuel door. Driver Information Center (DIC) if the fuel cap is not properly installed. WARNING: WARNING: Fuel can spray out on you if you open the fuel cap If a fire starts while you are refueling, do not too quickly.
Page 297: Filling A Portable Fuel Container
Filling a Portable Fuel Container WARNING: (Continued) WARNING: Bring the fill nozzle in contact with the inside of the fill opening before operating the nozzle. Never fill a portable fuel container while it is in Contact should be maintained until the filling is the vehicle.
Page 298: Checking Things Under The Hood
Checking Things Under WARNING: the Hood Things that burn can get on hot engine parts and WARNING: start a fire. These include liquids like fuel, oil, coolant, brake fluid, windshield washer and other fluids, and plastic or rubber. You or others could An electric fan under the hood can start up and be burned.
Page 299: Hood Release
Hood Release To open the hood: 1. Pull the hood release handle inside the vehicle. It is located next to the parking brake pedal near the floor. 2. Then go to the front of the vehicle and pull the secondary hood release to the right. The hood latch is located under the hood, near the center, at the front edge of the grille.
Page 300: Engine Compartment Overview
Engine Compartment Overview When you open the hood on the 3.9L V6 engine, here is what you will see: 6-14...
Page 301 A. Underhood Fuse Block on page 6 108. G. Engine Oil Fill Cap. See When to Add Engine Oil under Engine Oil on page 6 18. B. Remote Positive (+) Battery Terminal. See Jump Starting on page 6 44. H. Engine Oil Dipstick. See Checking Engine Oil under Engine Oil on page 6 18.
Page 302 When you open the hood on the 4.6L V8 engine, here is what you will see: 6-16...
Page 303 A. Underhood Fuse Block on page 6 108. G. Engine Oil Fill Cap. See When to Add Engine Oil under Engine Oil on page 6 18. B. Remote Positive (+) Terminal. See Jump Starting on page 6 44. H. Engine Oil Dipstick. See Checking Engine Oil under Engine Oil on page 6 18.
Page 304: Engine Oil
Engine Oil Checking Engine Oil It is a good idea to check the engine oil level at each To ensure proper engine performance and long life, fuel fill. In order to get an accurate reading, the vehicle careful attention must be paid to engine oil. Following must be on level ground.
Page 305: When To Add Engine Oil
When to Add Engine Oil Notice: Do not add too much oil. Oil levels above or below the acceptable operating range shown on the dipstick are harmful to the engine. If you find that you have an oil level above the operating range, i.e., the engine has so much oil that the oil level gets above the cross-hatched area that shows the proper operating range, the engine could be damaged.
Page 306 Selecting the Right Engine Oil Notice: Use only engine oil that is approved to the dexos specification or an equivalent engine Selecting the right engine oil depends on both the oil of the appropriate viscosity grade. Engine oils proper oil specification and viscosity grade: approved to the dexos specification will show the dexos symbol on the container.
Page 307: What To Do With Used Oil
Viscosity Grade sure to always select an oil that meets the required specification, dexos. See Specification earlier in this SAE 5W-30 is the best viscosity grade for the vehicle. section for more information. Do not use other viscosity oils such as SAE 10W 30, Engine Oil Additives/Engine Oil Flushes 10W 40, or 20W-50.
Page 308: Engine Oil Life System
Engine Oil Life System If the system is ever reset accidentally, the oil must be changed at 3,000 miles (5 000 km) since the last oil When to Change Engine Oil change. Remember to reset the oil life system whenever the oil is changed. This vehicle has a computer system that indicates when How to Reset the Engine Oil Life to change the engine oil and filter.
Page 309: Engine Air Cleaner/Filter
Engine Air Cleaner/Filter To inspect or replace the filter: See Engine Compartment Overview on page 6 14 for the location of the engine air cleaner/filter. When to Inspect the Engine Air Cleaner/Filter Inspect the air cleaner/filter at the scheduled maintenance intervals and replace it at the first oil change after each 50,000 mile (80 000 km) interval.
Page 310: Automatic Transmission Fluid
To reinstall the cover: Automatic Transmission Fluid 1. Align the two hinges located on the inboard side of When to Check and Change Automatic the cover. Transmission Fluid 2. Push the cover slightly down and towards the engine to engage the tabs in the hinges and align A good time to check the automatic transmission fluid the two screws.
Page 311: Checking The Fluid Level
Wait at least 30 minutes before checking the 3. With your foot on the brake pedal, move the shift transmission fluid level if you have been driving: lever through each gear range, pausing for about three seconds in each range. Then, position the When outside temperatures are above shift lever in P (Park).
Page 312: How To Add Automatic Transmission Fluid
How to Add Automatic Transmission Fluid Refer to the Maintenance Schedule to determine what kind of transmission fluid to use. See Recommended Fluids and Lubricants on page 7 8. If the fluid level is low, add only enough of the proper fluid to bring the level into the cross-hatched area on the dipstick.
Page 313: Cooling System
3. After adding fluid, recheck the fluid level as Cooling System described under How to Check Automatic The cooling system allows the engine to maintain the Transmission Fluid earlier in this section. correct working temperature. 4. When the correct fluid level is obtained, push the dipstick back in all the way.
Page 314: Engine Coolant (4.6L Engine)
WARNING: Heater and radiator hoses, and other engine parts, can be very hot. Do not touch them. If you do, you can be burned. Do not run the engine if there is a leak. If you run the engine, it could lose all coolant. That could cause an engine fire, and you could be burned.
Page 315: What To Use
Protects against rust and corrosion. The following explains the cooling system and how to check and add coolant when it is low. If there is a Will not damage aluminum parts. problem with engine overheating, see Engine Helps keep the proper engine temperature. Overheating on page 6 35.
Page 316: Checking Coolant
Checking Coolant Notice: This vehicle has a specific coolant fill procedure. Failure to follow this procedure could The vehicle must be on a level surface when checking cause the engine to overheat and be severely the coolant level. damaged. Check to see if coolant is visible in the coolant recovery tank.
Page 317: Engine Coolant (3.9L Engine)
4. With the coolant surge tank cap off, start the You can remove the engine and let it run until you can feel the upper coolant surge tank radiator hose getting hot. Watch out for the engine pressure cap when the cooling fans.
Page 318 Protects against rust and corrosion. What to Use Will not damage aluminum parts. Helps keep the proper engine temperature. WARNING: Notice: If an improper coolant mixture is used, the engine could overheat and be badly damaged. The Adding only plain water or some other liquid to the repair cost would not be covered by the vehicle cooling system can be dangerous.
Page 319: Recovery Tank
Checking Coolant How to Add Coolant to the Recovery Tank The vehicle must be on a level surface when checking the coolant level. WARNING: The coolant level should be at or above the FULL COLD mark when the engine is cold. The coolant level should be above the FULL COLD mark under normal You can be burned if you spill coolant on hot operating conditions.
Page 320: How To Add Coolant To The Radiator
How to Add Coolant to the Radiator If coolant is needed, add the proper mixture directly to the radiator, but be sure the cooling system is cool before this is done. WARNING: 1. You can remove the pressure cap when the cooling An electric engine cooling fan under the hood can system, including the start up even when the engine is not running and...
Page 321: Engine Overheating
5. Install the coolant recovery tank cap and the You may decide not to lift the hood when this warning pressure cap. After a day or two of driving, when appears, but instead get service help right away. See the engine is cold, check the coolant level in the Roadside Assistance Program on page 8 7.
Page 322: Engine Compartment
If Steam Is Coming From The Engine If No Steam Is Coming From The Compartment Engine Compartment If an engine overheat warning is displayed but no steam can be seen or heard, the problem may not be too WARNING: serious. Sometimes the engine can get a little too hot when the vehicle: Steam from an overheated engine can burn you Climbs a long hill on a hot day.
Page 323: Overheated Engine Protection
If the temperature overheat gauge is no longer in Notice: After driving in the overheated engine the overheat zone or an overheat warning no longer protection operating mode, to avoid engine damage, displays, the vehicle can be driven. Continue to drive allow the engine to cool before attempting any the vehicle slow for about 10 minutes.
Page 324: Windshield Washer Fluid
How to Check Power Steering Fluid Windshield Washer Fluid To check the power steering fluid: What to Use 1. Turn the key off and let the engine compartment When the vehicle needs windshield washer fluid, be cool down. sure to read the manufacturer's instructions before use. 2.
Page 325: Brakes
Notice: Brakes When using concentrated washer fluid, Brake Fluid follow the manufacturer's instructions for adding water. The brake master cylinder reservoir is filled with Do not mix water with ready-to-use washer DOT 3 brake fluid. See fluid. Water can cause the solution to freeze Engine Compartment and damage the washer fluid tank and other Overview on page 6 14...
Page 326 Do not top off the brake fluid. Adding fluid does not Always clean the brake fluid reservoir cap and the area correct a leak. If fluid is added when the linings are around the cap before removing it. This helps keep dirt worn, there will be too much fluid when new brake from entering the reservoir.
Page 327: Brake Wear
Brake Wear Notice: Continuing to drive with worn-out brake pads could result in costly brake repair. This vehicle has disc brakes. Disc brake pads have Some driving conditions or climates can cause a brake built-in wear indicators that make a high-pitched squeal when the brakes are first applied or lightly warning sound when the brake pads are worn and new applied.
Page 328: Battery
Brake Adjustment Battery Every time the brakes are applied, with or without the Refer to the replacement number on the original battery vehicle moving, the brakes adjust for wear. label when a new battery is needed. Replacing Brake System Parts DANGER: The braking system on a vehicle is complex.
Page 329 WARNING: A battery that is not properly vented can let sulfuric acid fumes into the area under the rear seat cushion. These fumes can damage the rear seat safety belt systems. You might not be able to see this damage and the safety belts might not provide the protection needed in a crash.
Page 330: Jump Starting
Vehicle Storage Jump Starting For more information about the vehicle battery, see WARNING: Battery on page 6 42. If the vehicle's battery has run down, you may want to use another vehicle and some jumper cables to start Batteries have acid that can burn you and gas your vehicle.
Page 331 Notice: Ignoring these steps could result in costly Notice: If the radio or other accessories are left on damage to the vehicle that would not be covered by during the jump starting procedure, they could be the warranty. damaged. The repairs would not be covered by the warranty.
Page 332 WARNING: Using an open flame near a battery can cause battery gas to explode. People have been hurt doing this, and some have been blinded. Use a flashlight if you need more light. Be sure the battery has enough water. You do not need to add water to the battery installed in your new vehicle.
Page 333 6. Connect the red positive (+) cable to the WARNING: positive (+) terminal of the dead battery. Use a remote positive (+) terminal if the vehicle has one. 7. Do not let the other end touch metal. Connect it to Fans or other moving engine parts can injure you the positive (+) terminal of the good battery.
Page 334 10. Now start the vehicle with the good battery and run the engine for a while. 11. Try to start the vehicle that had the dead battery. If it will not start after a few tries, it probably needs service. Notice: If the jumper cables are connected or removed in the wrong order, electrical shorting may occur and damage the vehicle.
Page 335: Headlamp Aiming
3. Disconnect the red positive (+) cable from the It is recommended that the vehicle is taken to your vehicle with the good battery. dealer for service if the headlamps need to be adjusted. It is possible however, to re-aim the headlamps as 4.
Page 336 Headlamp aiming is done with the vehicle's low-beam headlamps. The high-beam headlamps will be correctly aimed if the low-beam headlamps are aimed properly. To adjust the vertical aim: 1. Open the hood. See Hood Release on page 6 13 for more information. 4.
Page 337 9. Make sure that the light from the headlamp is positioned at the bottom edge of the horizontal tape line. The lamp on the left (A) shows the correct headlamp aim. The lamp on the right (B) 7. Locate the vertical headlamp aiming screws, which shows the incorrect headlamp aim.
Page 338: Bulb Replacement
Bulb Replacement Taillamps, Turn Signal, Stoplamps and Sidemarker Lamps For the proper type of replacement bulbs, see Replacement Bulbs on page 6 55. For any bulb changing procedure not listed in this section, contact your dealer. Halogen Bulbs WARNING: Halogen bulbs have pressurized gas inside and can burst if you drop or scratch the bulb.
Page 339 8. Pull the old bulb straight out of the socket. 9. Push the new bulb straight in until it clicks. 10. Push the bulb socket in and turn it clockwise to secure it in the taillamp assembly. 11. Push the taillamp assembly straight in to its original location.
Page 340: Taillamps And Back-Up Lamps
Taillamps and Back-Up Lamps To replace an auxiliary taillamp or back-up lamp bulb: 1. Open the trunk. See Trunk on page 3 12. A. Taillamp 2. Remove the three fasteners from the trunk trim. B. Back-up Lamp 3. Pull back the trunk trim to access the bulbs. 4.
Page 341: License Plate Lamp
7. Push the bulb socket in and turn it clockwise to Replacement Bulbs secure it. Exterior Lamps Bulb Number 8. Put the trunk trim and three fasteners back into Back-up Lamp 921LL place. Sidemarker, License Plate Lamp, 194LL License Plate Lamp and Auxiliary Taillamp Stoplamp, Taillamp, and Turn To replace one of these bulbs:...
Page 342 To replace the wiper blade assembly: 1. Turn the ignition to ACC/ACCESSORY with the engine off. 2. Pull the windshield wiper assembly away from the windshield. 4. Replace the blade assembly with a new one. Allowing the wiper blade arm to touch the windshield when no wiper blade is installed could damage the windshield.
Page 343: Tires
Tires WARNING: (Continued) Your new vehicle comes with high-quality tires made by a leading tire manufacturer. If you ever Over inflated tires are more likely to be have questions about your tire warranty and cut, punctured, or broken by a sudden where to obtain service, see your vehicle impact such as when you hit a pothole.
Page 344: Tire Sidewall Labeling
Tire Sidewall Labeling construction type, and service description. See the Tire Size illustration later in this section for Useful information about a tire is molded into its more detail. sidewall. The examples below show a typical (B) TPC Spec (Tire Performance Criteria passenger vehicle tire and a compact spare tire Specification) Original equipment tires designed...
Page 345 (E) Tire Ply Material The type of cord and number of plies in the sidewall and under the tread. (F) Uniform Tire Quality Grading (UTQG) Tire manufacturers are required to grade tires based on three performance factors: treadwear, traction, and temperature resistance. For more information see Uniform Tire Quality Grading on page 6 75.
Page 346: Tire Size
(B) Tire Ply Material The type of cord and (G) TPC Spec (Tire Performance Criteria number of plies in the sidewall and under the Specification) Original equipment tires designed tread. to GM's specific tire performance criteria have a TPC specification code molded onto the sidewall. (C) Tire Identification Number (TIN) The letters GM's TPC specifications meet or exceed all...
Page 347: Tire Terminology And Definitions
(C) Aspect Ratio A two digit number that Accessory Weight This means the combined indicates the tire height to width measurements. weight of optional accessories. Some examples of For example, if the tire size aspect ratio is 60, as optional accessories are, automatic transmission, shown in item C of the illustration, it would mean power steering, power brakes, power windows, that the tire's sidewall is 60 percent as high as it...
Page 348 DOT Markings A code molded into the sidewall Maximum Inflation Pressure The maximum of a tire signifying that the tire is in compliance air pressure to which a cold tire can be inflated. with the U.S. Department of Transportation (DOT) The maximum air pressure is molded onto the motor vehicle safety standards.
Page 349 Passenger (P-Metric) Tire A tire used on Treadwear Indicators Narrow bands, sometimes passenger cars and some light duty trucks and called wear bars, that show across the tread of multipurpose vehicles. a tire when only 1/16 inch (1.6 mm) of tread remains.
Page 350: Inflation - Tire Pressure
Inflation - Tire Pressure A vehicle specific Tire and Loading Information label is attached to your vehicle. This label shows Tires need the correct amount of air pressure to your vehicle's original equipment tires and the operate effectively. correct inflation pressures for your tires when they are cold.
Page 351: How To Check
How to Check Tire Pressure Monitor System Use a good quality pocket-type gauge to check The Tire Pressure Monitor System (TPMS) uses radio tire pressure. You cannot tell if your tires are and sensor technology to check tire pressure levels. The TPMS sensors monitor the air pressure in your properly inflated simply by looking at them.
Page 352: Tire Pressure Monitor Operation
Please note that the TPMS is not a substitute for proper Federal Communications Commission tire maintenance, and it is the driver's responsibility to (FCC) and Industry Canada maintain correct tire pressure, even if under inflation has not reached the level to trigger illumination of the See Radio Frequency Statement on page 8 18 TPMS low tire pressure telltale.
Page 353 A Tire and Loading Information label shows the size If the warning light comes on, stop as soon as possible of the original equipment tires and the correct inflation and inflate the tires to the recommended pressure pressure for the tires when they are cold. See Loading shown on the tire loading information label.
Page 354: Tpms Malfunction Light And Message
One or more TPMS sensors are missing or TPMS Malfunction Light and Message damaged. The malfunction light and the DIC The TPMS will not function properly if one or more of message should go off when the TPMS sensors the TPMS sensors are missing or inoperable. When are installed and the sensor matching process is the system detects a malfunction, the low tire pressure performed successfully.
Page 355: Tpms Sensor Matching Process
TPMS Sensor Matching Process 4. Start with the driver side front tire. 5. Place the relearn tool against the tire sidewall, Each TPMS sensor has a unique identification code. near the valve stem. Then press the button to The identification code needs to be matched to a new activate the TPMS sensor.
Page 356: Tire Inspection And Rotation
Tire Inspection and Rotation The purpose of a regular tire rotation is to achieve a uniform wear for all tires on the vehicle. This will We recommend that you regularly inspect your ensure that your vehicle continues to perform vehicle's tires, including the spare tire, for signs of most like it did when the tires were new.
Page 357: When It Is Time For New Tires
After the tires have been rotated, adjust the front Lightly coat the center of the wheel hub with and rear inflation pressures as shown on the Tire wheel bearing grease after a wheel change or tire and Loading Information label. See Inflation - Tire rotation to prevent corrosion or rust build-up.
Page 358: Buying New Tires
Buying New Tires The rubber in tires ages over time, even if they are not being used. This is also true for the spare tire, if your GM has developed and matched specific tires for vehicle has one. Multiple conditions affect how fast this your vehicle.
Page 359 GM recommends replacing tires in sets of four. WARNING: This is because uniform tread depth on all tires will help keep your vehicle performing most like it did when the tires were new. Replacing less Mixing tires could cause you to lose than a full set of tires can affect the braking control while driving.
Page 360: Different Size Tires And Wheels
Your vehicle's original equipment tires are listed WARNING: on the Tire and Loading Information Label. See Loading the Vehicle on page 5 18, for more information about the Tire and Loading Using bias-ply tires on the vehicle may Information Label and its location on your vehicle. cause the wheel rim flanges to develop cracks after many miles of driving.
Page 361: Uniform Tire Quality Grading
See Buying New Tires on page 6 72 and Accessories While the tires available on General Motors and Modifications on page 6 3 for additional passenger cars and light trucks may vary with information. respect to these grades, they must also conform to federal safety requirements and additional Uniform Tire Quality Grading General Motors Tire Performance Criteria (TPC)
Page 362: Wheel Alignment And Tire Balance
Traction AA, A, B, C the minimum required by law. Warning: The temperature grade for this tire is established for a The traction grades, from highest to lowest, tire that is properly inflated and not overloaded. are AA, A, B, and C. Those grades represent Excessive speed, underinflation, or excessive the tire's ability to stop on wet pavement as loading, either separately or in combination, can...
Page 363: Used Replacement Wheels
Your dealer will know the kind of wheel you need. Notice: The wrong wheel can also cause problems with bearing life, brake cooling, speedometer or Each new wheel should have the same load-carrying odometer calibration, headlamp aim, bumper height, capacity, diameter, width, offset, and be mounted the vehicle ground clearance, and tire or tire chain same way as the one it replaces.
Page 364: Tire Chains
Tire Chains Notice: If your vehicle has P225/60R16 size tires, use tire chains only where legal and only when you must. Use only SAE Class S type chains that are the WARNING: proper size for your tires. Install them on the front tires and tighten them as tightly as possible with the ends securely fastened.
Page 365 A rear blowout, particularly on a curve, acts much like a skid and may require the same correction you would WARNING: use in a skid. In any rear blowout remove your foot from the accelerator pedal. Get the vehicle under control by Lifting a vehicle and getting under it to do steering the way you want the vehicle to go.
Page 366: Tire Sealant And Compressor Kit
Tire Sealant and Compressor Kit WARNING: WARNING: Storing the tire sealant and compressor kit or other equipment in the passenger compartment of Idling a vehicle in an enclosed area with poor the vehicle could cause injury. In a sudden stop or ventilation is dangerous.
Page 367: Tire Sealant
Read and follow all of the tire sealant and compressor Tire Sealant kit instructions. Read and follow the safe handling instructions on the The kit includes: label adhered to the compressor. Check the tire sealant expiration date on the sealant canister.
Page 368: Punctured Tire
Using the Tire Sealant and Compressor See If a Tire Goes Flat on page 6 78 for other important safety warnings. Kit to Temporarily Seal and Inflate a Do not remove any objects that have penetrated Punctured Tire the tire. Follow the directions closely for correct sealant usage.
Page 369 If the vehicle only has a cigarette lighter, use the The pressure gauge (D) may read higher than cigarette lighter. the actual tire pressure while the compressor is on. Turn the compressor off to get an accurate Do not pinch the power plug cord in the door or pressure reading.
Page 370 15. Replace the sealant/air hose (F), and the power If the tire pressure has fallen more than 68 kPa plug (G) back in their original location. (10 psi) below the recommended inflation pressure, stop driving the vehicle. The tire is too 16.
Page 371 Using the Tire Sealant and Compressor Always do a safety check first. See If a Tire Goes Flat on page 6 78. Do not remove any objects that have Kit without Sealant to Inflate a Tire (Not penetrated the tire. Punctured) 1.
Page 372: Removal And Installation Of The Sealant Canister
7. Start the vehicle. The vehicle must be running 14. Replace the air only hose (E) and the power plug while using the air compressor. (G) and cord back in its original location. 8. Turn the selector switch (B) counterclockwise to 15.
Page 373: Tire Sealant And Compressor Kit Storage
4. Replace with a new canister which is available from your dealer. 5. Push the new canister into place. 6. Screw the connector (B) to the canister (A). 7. Slide the plastic cover back on. Tire Sealant and Compressor Kit Storage The tire sealant and compressor kit is located in the trunk.
Page 374: Changing A Flat Tire
Changing a Flat Tire When the vehicle has a flat tire (B), use the following example as a guide to assist you in the placement of If a tire goes flat, avoid further tire and wheel damage wheel blocks (A). by driving slowly to a level place, well off the road, if possible.
Page 375: Removing The Spare Tire And Tools
Removing the Spare Tire and Tools The equipment you will need is located in the trunk. 1. Open the trunk. See Trunk on page 3 12. 2. Turn the center retainer counterclockwise to remove it. 4. Turn the retainer that secures the jack and wheel wrench counterclockwise and remove the washer.
Page 376 Removing the Flat Tire and Installing the Spare Tire 1. Do a safety check before proceeding. See Changing a Flat Tire on page 6 88. The tools you will be using include the jack (A) and the wheel wrench (B). 2.
Page 377 WARNING: Raising the vehicle with the jack improperly positioned can damage the vehicle and even make the vehicle fall. To help avoid personal injury and vehicle damage, be sure to fit the jack lift head into the proper location before raising the vehicle.
Page 378 5. Position the jack and raise the jack head until it fits firmly on the ridge in the vehicle's frame nearest the flat tire. Do not raise the vehicle yet. 6. Put the compact spare tire near the flat tire. WARNING: Getting under a vehicle when it is jacked up is dangerous.
Page 379 8. Remove all wheel WARNING: nuts and remove the flat tire. Rust or dirt on a wheel, or on the parts to which it is fastened, can make wheel nuts become loose after time. The wheel could come off and cause an accident.
Page 380 10. Install the compact spare tire. WARNING: Never use oil or grease on bolts or nuts because the nuts might come loose. The vehicle's wheel could fall off, causing a crash. 11. Put the wheel nuts back on with the rounded end of the nuts toward the wheel.
Page 381 13. Tighten the wheel nuts WARNING: firmly in a crisscross sequence as shown. Wheel nuts that are improperly or incorrectly tightened can cause the wheels to become loose or come off. The wheel nuts should be tightened with a torque wrench to the proper torque specification after replacing.
Page 382: Storing A Flat Or Spare Tire And Tools
Storing a Flat or Spare Tire and To store the compact spare tire and tools: Tools WARNING: Storing a jack, a tire, or other equipment in the passenger compartment of the vehicle could cause injury. In a sudden stop or collision, loose equipment could strike someone.
Page 383: Compact Spare Tire
The compact spare tire is for temporary use only. A. Center Retainer F. Spare Tire Replace the compact spare tire with a full-size tire B. Compact Spare G. Wheel Wrench as soon as you can. See Compact Spare Tire on Tire Cover H.
Page 384: Appearance Care
After installing the compact spare on the vehicle, stop Appearance Care as soon as possible and make sure the spare tire is correctly inflated. The compact spare is made to Interior Cleaning perform well at speeds up to 65 mph (105 km/h) for distances up to 3,000 miles (5 000 km), so you can The interior will continue to look its best if it is cleaned finish your trip and have the full-size tire repaired or...
Page 385: Fabric/Carpet
Laundry detergents or dishwashing soaps with Notice: Using abrasive cleaners when cleaning degreasers can leave residue that streaks and glass surfaces on the vehicle, could scratch the attracts dirt. For liquid cleaners, about 20 drops per glass and/or cause damage to the rear window gallon (3.78 L) of water is a good guide.
Page 386: Leather
To clean: Leather 1. Saturate a lint-free, clean white cloth with water or Leather, and lighter colored leather in particular, will club soda. need more frequent cleaning to prevent the buildup of 2. Wring the cloth to remove excess moisture. dust, dirt, and colors transferred from other items so that these do not become permanent stains.
Page 387: Care Of Safety Belts
Instrument Panel, Vinyl, and Other Care of Safety Belts Plastic Surfaces Keep belts clean and dry. A soft cloth dampened with water may be used to remove dust. If a more thorough cleaning is necessary, WARNING: a clean soft cloth dampened with a mild soap solution can be used to gently remove dust and dirt.
Page 388: Washing Your Vehicle
Washing Your Vehicle High pressure car washes may cause water to enter the vehicle. Avoid using high pressure washes closer than The best way to preserve the vehicle's finish is to keep 12 inches (30 cm) to the surface of the vehicle. Use of it clean by washing it often.
Page 389: Windshield And Wiper Blades
Foreign materials such as calcium chloride and other Windshield and Wiper Blades salts, ice melting agents, road oil and tar, tree sap, bird Clean the outside of the windshield with glass cleaner. droppings, chemicals from industrial chimneys, etc., can damage the vehicle's finish if they remain on painted Clean the rubber blades using a lint free cloth or paper surfaces.
Page 390: Aluminum Or Chrome-Plated Wheels
Aluminum or Chrome-Plated Wheels The surface of these wheels is similar to the painted surface of the vehicle. Do not use strong soaps, and Trim chemicals, abrasive polishes, abrasive cleaners, cleaners with acid, or abrasive cleaning brushes on The vehicle may have either aluminum or them because they could damage the surface.
Page 391: Tires
Tires Finish Damage To clean the tires, use a stiff brush with tire cleaner. Any stone chips, fractures or deep scratches in the finish should be repaired right away. Bare metal will Notice: Using petroleum-based tire dressing corrode quickly and may develop into major repair products on the vehicle may damage the paint finish expense.
Page 392: Chemical Paint Spotting
Chemical Paint Spotting Vehicle Identification Some weather and atmospheric conditions can create a Vehicle Identification Number (VIN) chemical fallout. Airborne pollutants can fall upon and attack painted surfaces on the vehicle. This damage can take two forms: blotchy, ring-shaped discolorations, and small, irregular dark spots etched into the paint surface.
Page 393: Service Parts Identification Label
Service Parts Identification Label Add-on equipment can drain the vehicle battery, even if the vehicle is not operating. This label, on the spare tire cover, has the following The vehicle has an airbag system. Before attempting to information: add anything electrical to the vehicle, see Servicing Vehicle Identification Number (VIN).
Page 394: Fuses And Circuit Breakers
Fuses and Circuit Breakers The MaxiFuses are located in two fuse blocks, one located in the engine compartment on the passenger's The wiring circuits in your vehicle are protected from side and the other under the rear seat on the driver's short circuits by a combination of fuses and circuit side.
Page 395 Fuses Usage Fuses Usage Engine Control Module (ECM), Crank Air Injection Reactor (AIR) Solenoid Fuel Injectors Odd Oxygen Sensor Fuel Injectors Even Emission Device Air Conditioning Clutch Transmission, Ignition 1 6-109...
Page 396: Rear Underseat Fuse Block
Fuses Usage Fuses Usage Engine Control Module (ECM), Cooling Fan 2 (J-Case) Powertrain Control Module (PCM) Cooling Fan 1 (J-Case) Climate Control System, Instrument Panel Cluster Ignition 1 Relays Usage Airbag System Powertrain Horn Starter Windshield Wiper Cooling Fan 2 Fog Lamps Cooling Fan 3 Right High-Beam Headlamp...
Page 397 Removing the Rear Seat Cushion Notice: If you touch the exposed wires with the metal on the seat cushion, you could cause a short that could damage the battery and or wires. Avoid contact between the rear seat and the fuse center whenever you remove or reinstall the rear seat.
Page 398 To reinstall the rear seat cushion, do the following: WARNING: (Continued) will not be there to work for the next passenger. The person sitting in that position could be badly injured. After reinstalling the seat cushion, always check to be sure that the safety belts are properly routed and are not twisted.
Page 399 Fuses Usage Fuses Usage Fuel Pump Engine Control Module (ECM)/ Transmission Control Module (TCM) Left Park Lamp Memory Module Not Used Not Used Right Park Lamp 6-113...
Page 400 Fuses Usage Fuses Usage Steering Wheel Illumination Retained Accessory Power 1 (RAP) Front Heated/Cooled Seat Module Passenger Door Module Run 2 - Heated/Cooled Seats Sensing and Diagnostic Module Not Used Accessory Power Outlets RPA Module Body Control Module (BCM) (Inadvertent) ®...
Page 401 Fuses Usage Relays Usage Electronic Leveling Control Unlock Compressor (J-Case) Lock Blower (J-Case) Not Used Daytime Running Lamps Not Used Resistor Usage Trunk Release Terminating Resistor Not Used Not Used Relays Usage Retained Accessory Power (RAP) Not Used Rear Defogger Circuit Usage Electronic Leveling Control...
Page 402: Capacities And Specifications
Capacities and Specifications The following approximate capacities are given in English and metric conversions. See Recommended Fluids and Lubricants on page 7 8 for more information. Capacities Application English Metric For the air conditioning system refrigerant charge Air Conditioning Refrigerant R134a amount, see the refrigerant label located under the hood.
Page 403 Engine Specifications Engine VIN Code Transmissions Spark Plug Gap 3.9L V6 Engine Automatic 0.040 in (1.01 mm) 4.6L V8 Engine Automatic 0.050 in (1.27 mm) 6-117...
Page 404 NOTES 6-118...
Page 405 Section 7 Maintenance Schedule Maintenance Schedule ......7-2 Recommended Fluids and Lubricants ... 7-8 Introduction .
Page 406: Introduction
are driven on reasonable road surfaces within legal Maintenance Schedule driving limits. use the recommended fuel. See Gasoline Octane Introduction on page 6 6. Maintenance intervals, checks, inspections, recommended fluids, and lubricants are necessary WARNING: to keep this vehicle in good working condition. Damage caused by failure to follow scheduled maintenance might not be covered by the vehicle Performing maintenance work on a vehicle can be...
Page 407: Scheduled Maintenance
Rotation of New Tires Every Engine Oil Change To maintain ride, handling, and performance of the Change engine oil and filter. Reset oil life system. vehicle, it is important that the first rotation service for See Engine Oil on page 6 18 and Engine Oil Life new tires be performed.
Page 408: Additional Required Services
Fluids visual leak check (or every 12 months, Additional Required Services whichever occurs first). A leak in any system must be repaired and the fluid level checked. Every 12 000 km/7,500 Miles Engine air cleaner filter inspection. See Engine Air Rotate tires.
Page 409 Once a Year First Engine Oil Change After Every 40 000 km/25,000 Miles Starter switch check. See Owner Checks and Services on page 7 6. Passenger compartment air filter replacement (or every 24 months, whichever occurs first). Automatic transmission shiftlock control function More frequent replacement may be needed if check.
Page 410: Owner Checks And Services
Replace as needed. An Emission Control Service. Owner Checks and Services The U.S. Environmental Protection Agency or the Starter Switch Check California Air Resources Board has determined that the failure to perform this maintenance item will not nullify the emission warranty or limit WARNING: recall liability prior to the completion of the vehicle's useful life.
Page 411: Ignition Transmission Lock Check
Automatic Transmission Shift Lock 3. With the engine off, turn the ignition to ON/RUN, but do not start the engine. Without applying the Control Function Check regular brake, try to move the shift lever out of P (Park) with normal effort. If the shift lever moves out of P (Park), contact your dealer for service.
Page 412: Recommended Fluids And Lubricants
Parking Brake and Automatic Recommended Fluids and Transmission P (Park) Mechanism Lubricants Check Fluids and lubricants identified below by name, part number, or specification can be obtained from your dealer. WARNING: Usage Fluid/Lubricant The engine requires engine oil When you are doing this check, the vehicle could approved to the dexos specification.
Page 413 Usage Fluid/Lubricant Usage Fluid/Lubricant Windshield Hood Latch ® Optikleen Washer Solvent. Washer Assembly, Lubriplate Lubricant Aerosol Secondary (GM Part No. 12346293, in Chassis Lubricant Latch, Canada 992723) or lubricant (GM Part No. 12377985, in Parking Brake Pivots, Spring meeting requirements of NLGI #2, Canada 88901242) or lubricant Cable Guides Anchor, and...
Page 414: Maintenance Replacement Parts
Maintenance Replacement Parts Replacement parts identified below by name, part number, or specification can be obtained from your dealer. Maintenance Replacement Parts Part GM Part Number ACDelco Part Number Engine Air Cleaner/Filter 22676970 A1627C Engine Oil Filter 3.9L V6 Engine 89017342 PF61 4.6L V8 Engine...
Page 415: Engine Drive Belt Routing
Engine Drive Belt Routing 4.6L V8 Engine 3.9L V6 Engine 7-11...
Page 416: Maintenance Record
Maintenance Record After the scheduled services are performed, record the date, odometer reading, who performed the service, and the type of services performed in the boxes provided. Retain all maintenance receipts. Maintenance Record Odometer Date Serviced By Services Performed Reading 7-12...
Page 417 Maintenance Record (cont.) Odometer Date Serviced By Services Performed Reading 7-13...
Page 418 Maintenance Record (cont.) Odometer Date Serviced By Services Performed Reading 7-14...
Page 419: Customer Assistance Information
Section 8 Customer Assistance Information Customer Assistance and Information ... 8-2 Reporting Safety Defects ......8-13 Customer Satisfaction Procedure .
Page 420: Customer Assistance And Information
Your satisfaction and goodwill are important to your the top left of the instrument panel and visible dealer and to Buick. Normally, any concerns with the through the windshield. sales transaction or the operation of your vehicle will be Dealership name and location.
Page 421 The BBB Auto Line Program is an out of court program This program is available in all 50 states and the administered by the Council of Better Business Bureaus District of Columbia. Eligibility is limited by vehicle age, to settle automotive disputes regarding vehicle repairs mileage, and other factors.
Page 422: Online Owner Center
My Dealers: Save details such as address and Store online service and maintenance records phone number for each of your preferred GM Buick dealer locator for service nationwide dealers. Exclusive privileges and offers...
Page 423: Customer Assistance For Text Telephone (Tty)
Buick encourages customers to call the toll-free number vehicles you own to your driveway profile. for assistance. However, if a customer wishes to write or e-mail Buick, the letter should be addressed to: My Preferences: Manage your profile and use tools and forms with greater ease.
Page 424: Gm Mobility Reimbursement Program
Canada GM Mobility Reimbursement Program General Motors of Canada Limited Customer Communication Centre, Mail Code: CA1-163-005 1908 Colonel Sam Drive Oshawa, Ontario L1H 8P7 www.gm.ca 1-800-263-3777 (English) 1-800-263-7854 (French) 1-800-263-3830 (For Text Telephone devices (TTYs)) This program is available to qualified applicants for Roadside Assistance: 1-800-268-6800 cost reimbursement of eligible aftermarket adaptive equipment required for your vehicle, such as hand...
Page 425: Roadside Assistance Program
Calling for Assistance Roadside Assistance is not a part of the New Vehicle Limited Warranty. Buick and General Motors of Canada When calling Roadside Assistance, have the following Limited reserve the right to make any changes or...
Page 426: Services Not Included In Roadside Assistance
Emergency Tow From a Public Road or Services Specific to Highway: Tow to the nearest Buick dealer for Canadian Purchased Vehicles warranty service, or if the vehicle was in a crash and cannot be driven. Assistance is also given Fuel delivery: Reimbursement is approximately when the vehicle is stuck in sand, mud, or snow.
Page 427: Scheduling Service Appointments
Alternative Service: If assistance cannot be Courtesy Transportation Program provided right away, the Roadside Assistance advisor may give permission to get local To enhance your ownership experience, we and our emergency road service. You will receive payment, participating dealers are proud to offer Courtesy up to $100, after sending the original receipt to Transportation, a customer support program for vehicles Roadside Assistance.
Page 428: Transportation Options
Transportation Options Courtesy Rental Vehicle The dealer may arrange to provide you with a courtesy Warranty service can generally be completed rental vehicle or reimburse you for a rental vehicle while you wait. However, if you are unable to wait, that you obtain if the vehicle is kept for an overnight GM helps to minimize inconvenience by providing warranty repair.
Page 429: Collision Damage Repair
Collision Damage Repair originally designed appearance and safety performance; however, the history of these parts is not known. Such If your vehicle is involved in a collision and it is parts are not covered by your GM New Vehicle Limited damaged, have the damage repaired by a qualified Warranty, and any related failures are not covered by technician using the proper equipment and quality...
Page 430: Insuring Your Vehicle
Insuring Your Vehicle Give only the necessary information to police and other parties involved in the crash. Protect your investment in your GM vehicle with For emergency towing see Roadside Assistance comprehensive and collision insurance coverage. There Program on page 8 7. are significant differences in the quality of coverage afforded by various insurance policy terms.
Page 431: Reporting Safety Defects
Managing the Vehicle Damage Repair Reporting Safety Defects Process Reporting Safety Defects to the In the event that your vehicle requires damage repairs, United States Government GM recommends that you take an active role in its repair. If you have a pre-determined repair facility of If you believe that your vehicle has a defect which choice, take your vehicle there, or have it towed there.
Page 432: Detroit, Mi
General Motors. Service Bulletins Call 1-800-521-7300, or write: Service Bulletins give additional technical service Buick Customer Assistance Center information needed to knowledgeably service P.O. Box 33136 General Motors cars and trucks. Each bulletin contains...
Page 433: Owner Information
Owner Information Current and Past Models Owner publications are written specifically for owners Technical Service Bulletins and Manuals are available and intended to provide basic operational information for current and past model GM vehicles. about the vehicle. The Owner Manual includes the ORDER TOLL FREE: 1-800-551-4123 Maintenance Schedule for all models.
Page 434: Vehicle Data Recording And Privacy
Vehicle Data Recording and Event Data Recorders Privacy This vehicle has an Event Data Recorder (EDR). The main purpose of an EDR is to record, in certain crash Your GM vehicle has a number of sophisticated or near crash-like situations, such as an airbag computers that record information about the vehicle s deployment or hitting a road obstacle, data that will performance and how it is driven.
Page 435: Onstar
This data can help provide a better understanding of the GM will not access this data or share it with others circumstances in which crashes and injuries occur. except: with the consent of the vehicle owner or, if the vehicle is leased, with the consent of the lessee; in Important: EDR data is recorded by your vehicle only if response to an official request of police or similar a non-trivial crash situation occurs;...
Page 436: Navigation System
Navigation System Radio Frequency Statement If the vehicle has a navigation system, use of the This vehicle has systems that operate on a radio system may result in the storage of destinations, frequency that comply with Part 15 of the Federal addresses, telephone numbers, and other trip Communications Commission (FCC) rules and with information.
Page 437 Antilock Brake System (ABS) ......5-4 Warning Light ........4-33 Accessories and Modifications .
Page 438 Audio System (cont.) Bulb Replacement ....... . . 6-55 Setting the Clock ....... . . 4-68 Fog Lamps .
Page 439 Center Flex Storage Unit ......3-49 Cleaning (cont.) Interior ..........6-98 Center Seat .
Page 440 Courtesy Transportation Program ....8-9 Door Delayed Locking ........3-10 Cruise Control .
Page 441 Engine (cont.) Overheated Protection Operating Mode ..6-37 E85 Fuel ..........6-7 Overheating .
Page 442 Fog Lamps Bulb Replacement ....... . 4-12 Garage Door Opener ......3-42 Front Fog Lamps Gasoline Light .
Page 443 Heated Steering Wheel ........4-4 Keyless Entry Heated Seats .
Page 444 Lights Locks (cont.) Power Door ........3-9 Airbag Readiness .
Page 445 Mirrors (cont.) Operation, Universal Home Remote System ..3-42 Outside Heated Mirrors ......3-34 Outlet Adjustment .
Page 446 Passenger Airbag Status Indicator ....4-31 Passenger Compartment Air Filter ....4-25 Radio Frequency Passenger Sensing System .
Page 447 Replacement Parts Safety Belts (cont.) Reminders ........4-29 Maintenance .
Page 448 Service ..........6-3 Steering .
Page 449 Theater Dimming ........4-13 Tires (cont.) Sidewall Labeling ....... . . 6-58 Theft-Deterrent Feature .
Page 450 Ultrasonic Rear Parking Assist (URPA) ... . 3-35 Warning Lights, Gauges, and Indicators ... 4-27 Uniform Tire Quality Grading ..... . 6-75 Warnings Universal Home Remote System .

Buick Lucerne 2011 Owner's Manual

Table of Contents

Section 2 Seats and Restraint System

Section 3 Features and Controls

Section 4 Instrument Panel

Section 5 Driving Your Vehicle

Quick Links

Chapters

Related Manuals for Buick Lucerne 2011

Summary of Contents for Buick Lucerne 2011