Advertisement

Quick Links

VMD2
(6901-002124 <00>)
I N S T A L L A T I O N I N S T R U C T I O N S
Sanus
2221 Hwy 36 West
Saint Paul, MN 55113 USA
Customer Service
Americas: 800-359-5520 • 651-484-7988 • info@sanus.com
Europe, Middle East, and Africa: + 31 40 2324700 • europe.sanus@milestone.com
Asia Pacific: 86 755 8996 9226 • sanus.ap@milestone.com
www.sanus.com

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the VMD2 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Sanus VMD2

  • Page 1 I N S T A L L A T I O N I N S T R U C T I O N S Sanus 2221 Hwy 36 West Saint Paul, MN 55113 USA Customer Service Americas: 800-359-5520 • 651-484-7988 • info@sanus.com Europe, Middle East, and Africa: + 31 40 2324700 • europe.sanus@milestone.com Asia Pacific: 86 755 8996 9226 • sanus.ap@milestone.com www.sanus.com...
  • Page 2: Important Warnings And Cautions

    Milestone AV Technologies, a Duchossois Group Company. component. The wall to which the mount is being attached All rights reserved. Sanus is a division of Milestone. may have a maximum drywall thickness of 5/8" (1.6cm). All other brand names or marks are used for identification purposes and are trademarks of their respective owners.
  • Page 3: Installation Instructions

    Installation Instructions VMD2 LEGEND Tighten Fastener Pencil Mark Apretar elemento de fijación Marcar con lápiz Befestigungsteil festziehen Stiftmarkierung Apertar fixador Marcar com lápis Serrare il fissaggio Segno a matita Bevestiging vastdraaien Potloodmerkteken Serrez les fixations Marquage au crayon Loosen Fastener Drill Hole Aflojar elemento de fijación...
  • Page 4: Tools Required For Installation

    VMD2 Installation Instructions TOOLS REQUIRED FOR INSTALLATION 3/16" (included) PARTS A (1) [monitor arm] B (4) C (4) D (4) M4x14mm M4x25mm M10x5.3x10 E (1) 3/16" (6901-002124 <00>)
  • Page 5: Assembly And Installation

    RECESSED mounting holes, then proceed to "DISPLAY INSTALLATION" before continuing with this mount installation procedure. Connecting VMD2 to Desk Standard Installation Loosen clamp screw until enough space is created between clamp and mount to allow for desk mounting. (See Figure 1) NOTE: If space is limited behind desk (i.e.
  • Page 6: Display Installation

    VMD2 Installation Instructions Display Installation The mounting holes on the back of the display will either be Using Phillips screwdriver, install two remaining M4x14mm Phillips screws (B) through the lower mounting holes in flush with the back surface or recessed into the back surface.
  • Page 7 Installation Instructions VMD2 Adjustments Pivot Adjustment Range Column Height Adjustment Adjust arm angle as desired up to 90 degrees in either Loosen column adjustment knob. (See Figure 7) direction. (See Figure 8) Adjust height to desired level. (See Figure 7) Tighten column adjustment knob.
  • Page 8: Cable Management

    VMD2 Installation Instructions Swing Arm Pivot Adjustment Cable Management Adjust pivot position as desired. (See Figure 9) Route cables through cable management channels. (See Figure 10) Adjust pivot point tension screws to change pivot adjustment tension. (See Figure 9) cable (typical)

Table of Contents