Advertisement
Quick Links
Advertisement
Related Manuals for Seenergy SVR-504
Summary of Contents for Seenergy SVR-504
- Page 1 Network Video Recorder User’s Manual v1.0.0 SVR-504/508/516/516+ Model:...
-
Page 2: Table Of Contents
SVR-500 Series Network Video Recorder Table of Contents Product Description Install Hard Disk Hardware Illustration I/O Ports and RS-485 LEDs Definition Connect to the NVR... - Page 3 SVR-500 Series Network Video Recorder...
- Page 4 Any risk arising from the use of this information rests with the recipi- ent, and nothing herein should be construed as constituting any kind of warranty. SEEnergy reserves the right to make adjustments without prior notifi- cation. All names of people and organizations used in this documentís ex- amples are fictitious.
-
Page 5: System Requirements
SVR-500 Series Network Video Recorder System Requirements The following are minimum system requirements for the system to op- erate Embedded Network Video Recorder (ENVR): Operating System Microsoft® Windows® XP Professional SP2, Windows Vista, Windows 7, Windows® 2003 Server, or Windows® 2008 Server Browser Microsoft Internet Explorer 7 or above Minimum Intel®... -
Page 6: Product Description
Up to 4 (for SVR-504) or 8 (for SVR-508) or 16 (for SVR-516) cameras can be connected via a net- work and it is possible to record their camera pictures. -
Page 7: Install Hard Disk
SVR-500 Series Network Video Recorder Install Hard Disk Start by removing the screws on the side: Push the top housing forward. Then lift it up. • The NVR supports SATA I or SATA II hard disks. • The NVR supports max. 3TB per hard disk and it supports total of 2 hard disks (6TB). - Page 8 SVR-500 Series Network Video Recorder There is a cable connected between the fron LED board and the main board. You can remove it from the main board or simply put the top housing on the side like shown below. Next, slide the hard drive into the tray.
- Page 9 SVR-500 Series Network Video Recorder Make sure the SATA connectors are correctly aligned with each other. Secure the hard drive with the tool-less screw provided in the box. Place the top housing back and secure it with the bottom housing.
-
Page 10: Hardware Illustration
SVR-500 Series Network Video Recorder Hardware Illustration (Front) -
Page 11: Leds Definition
SVR-500 Series Network Video Recorder LEDs Definition Solid green when the hard disk is mounted Green and being accessed. Solid red for disk fail. HDD x 2 Solid amber when recording is in process. Amber Blinking when recycling. Amber Solid amber for activity on a 1G bps network. Network Solid green for activity on a 10/100 Mbps Green... - Page 12 SVR-500 Series Network Video Recorder I/O Ports and RS-485 (Rear) SVR-504/508/516 SVR-516+...
- Page 13 SVR-500 Series Network Video Recorder Signal 12V DC 3~10 Alarm input Out1 Out2 Out3 Out4 RS485+ RS485-...
-
Page 14: Connect To The Nvr
Use SEEnergy Device Search Utility When the NVR is on a corporate network, or a local area network where a DHCP server is already present. Run the “SEEnergy Device Search” utility from a computer which is also on the same network and locate the NVR via its IP address assigned by the top-level DHCP server. - Page 15 SVR-500 Series Network Video Recorder Once the installation is complete, check the “Launch the Search AP” option and click “Finish”: The search should start automatically and its status should be dis- played: The NVR should be located and its IP address should be displayed: Double-click on it and the program should automatically access the NVR’s web administration page from your default browser You may change NVR’s IP address by click on the button highlighted...
- Page 16 SVR-500 Series Network Video Recorder You will be prompted for the NVR’s login information before proceeding to change device’s IP address. You may click on the button highlighted below to perform search again. Or double-click on any of the search results to access NVR’s web ad- ministration page access NVR’s web administration page perform search again...
- Page 17 SVR-500 Series Network Video Recorder Access NVR with its default IP address The NVR comes with a pre-configured static IP “192.168.101.50”. However, it is only used when there is no DHCP server presented in the network. The NVR will turn on its DHCP server function and act as the DHCP server in the network.
- Page 18 The specification is subject to change without prior notice. SEEnergy endeavors to ensure that the information in this document is correct and faily stated but does not accept liability for any...