Installation ................7
HDD Installation ................7 Connect to the NVR ............... 10 Use SEEnergy Device Search Utility ..........10 Access the NVR with its default IP address ........15 Set up Password ................16 ...
Page 3
SVR-‐632/664
U ser’s
M anual
Network Settings ................. 67 DDNS Service ................69 Time and Date ................76 User Account ................77 Add a new user ................78 Change the password of the “admin” account ........79 ...
SVR-‐632/664
U ser’s
M anual
Installation HDD Installation Release the HDD tray by pulling the lock to the right. Pull the HDD tray out of the case.
Page 8
8
SVR-‐632/664
U ser’s
M anual
Place the HDD in the tray and Put the HDD tray back to the case. Secure it with the screws at the bottom of the tray.
Page 9
SVR-‐632/664
U ser’s
M anual
Push the tray door back to the case to secure it.
Use SEEnergy Device Search Utility If the NVR is placed in a corporate network or a local area network where a DHCP server is already presented, run the “SEEnergy Device Search” utility from a computer that is on the same network and locate the NVR with its IP address that is assigned by the top-level DHCP server.
Page 11
SVR-‐632/664
U ser’s
M anual
To begin, launch the “SEEnergy Deivce Search” utility from the CD and proceed with the installation:...
Page 12
12
SVR-‐632/664
U ser’s
M anual
Once the installation is complete, check the “Launch the Search AP” option and click “Finish”. The search should start automatically and its status should be dis- played.
Page 13
SVR-‐632/664
U ser’s
M anual
The NVR should be located and its IP address should be displayed. Double-click on an NVR and the search program should automati- cally access the NVR’s web administration page from your default browser.
Page 14
14
SVR-‐632/664
U ser’s
M anual
You should be prompted for the the NVR’s username and password. Enter its default username “admin” and password “admin” and then click”OK” to enter the system...
SVR-‐632/664
U ser’s
M anual
Access the NVR with its default IP address The NVR comes with a pre-configured static IP “192.168.101.50”. However, it is only used when there is no DHCP server presented in the network. The NVR will turn on its DHCP server function and act as the DHCP server in the network.
16
SVR-‐632/664
U ser’s
M anual
Again, you should be prompted for the username and password. Enter its default username “admin” and password “admin” and then click”OK” to enter the system Set up Password...
Page 17
SVR-‐632/664
U ser’s
M anual
The default login username and password is admin/admin. To change the password of the admin account, go to “Setup” --> “System Con- figurations” --> “User Account”, click on the “admin” account in the account list then press the “edit”...
18
SVR-‐632/664
U ser’s
M anual
Camera Installation Add a Camera -- Automatic Search Click the “Search” button to perform the camera search. You should be prompted to install Active Control component in order for the search to function properly. Go ahead and click “Install”...
Page 19
SVR-‐632/664
U ser’s
M anual
After that, the search should begin and its status should be displayed: Found cameras should be listed and simply select a camera from the list and press “Configure”...
20
SVR-‐632/664
U ser’s
M anual
Its corresponding information should be displayed in the “Camera Information” section. Enter its username and password and select the channel ID and name the camera. Click on “Detect” to establish connection between the recorder and the camera.
Page 21
SVR-‐632/664
U ser’s
M anual
Simply follow the instruction described above but instead of using the “Search” function, enter the camera’s IP address and credential in the “Camera Information” manually...
22
SVR-‐632/664
U ser’s
M anual
Live View The “Live View” page provides the following functions: • Retrieve camera’s video stream • Retrieve camera’s status • Perform Live Sequence Viewing • PTZ Control • Perform PTZ Preset Sequence viewing •...
SVR-‐632/664
U ser’s
M anual
Retrieve camera’s video stream The camera list is expanded and displayed on the Live View page: • Click “All” to display videos of all 32 channels • Click “1-16” or "17-32" to display videos of in 16-video view •...
24
SVR-‐632/664
U ser’s
M anual
Red: Performing event recording Green: Recording (manual/continuous/schedule) White: This channel is not configured with any camera Perform Sequence Viewing Sequence view is a function that allows you to view multiple video streams from certain cameras in sequence automatically without having to select them one by one.
Page 25
SVR-‐632/664
U ser’s
M anual
Next, select one or more camera(s) or camera group(s) for sequence viewing: Select "1-16" and "17-32" to start sequence viewing in 16-video view Select "Group(x)" to start sequence viewing in quad view Select "cameras"...
26
SVR-‐632/664
U ser’s
M anual
Then, select dwell interval from the drop-down menu and click "Start" to begin. PTZ Control PTZ control provides functions to pan, tilt, zoom a PTZ camera as well as the ability to adjust camera focus and iris.
Page 27
SVR-‐632/664
U ser’s
M anual
Only PTZ capable cameras will be listed in the drop-down menu...
28
SVR-‐632/664
U ser’s
M anual
The bar highlighted above controls the moving angle. Larger number means bigger movement angle. Perform PTZ Preset Viewing There are three functions provided in the “Preset” section: • Perform preset point viewing of a particular camera •...
SVR-‐632/664
U ser’s
M anual
Preset Point Viewing Start by selecting a PTZ camera from the drop-down list Its available PTZ preset points will be listed in the drop-down list shown below. Click "Go to" to move to the selected position.
30
SVR-‐632/664
U ser’s
M anual
Auto Pan Viewing Use the Auto Pan control buttons to pan right, left and stop auto pan * Certain cameras do not support bi-directional pan movements. Use the “Autopan” button for such cameras Preset Point Sequence Viewing This function allows you to view multiple preset points from a video of a camera without having to select them one by one.
SVR-‐632/664
U ser’s
M anual
the recorder will begin to display videos from those preset points in sequence automatically until you click “Stop” Live Video Controls Users can perform certain functions to a live view video. They can be accessed by right-clicking on a video.
32
SVR-‐632/664
U ser’s
M anual
Take a snapshot of a live video To take a snapshot of a live video, right-click on the video and select "Take Snapshot".
Page 33
SVR-‐632/664
U ser’s
M anual
An additional window containing the captured image should be displayed. Right-click anywhere on the image and select "Save Picture As..." to save the image.
Page 34
34
SVR-‐632/664
U ser’s
M anual
A dialog should be displayed that allows you to choose a directory/folder of where the snapshot will be saved to.
SVR-‐632/664
U ser’s
M anual
Perform Digital PTZ To perform digital PTZ on a particual channel, right-click anywhere on its video and select "Digital PTZ".
Page 36
36
SVR-‐632/664
U ser’s
M anual
Next, hold the mouse left button and draw a square on the video to specify the zoom in area...
Page 37
SVR-‐632/664
U ser’s
M anual
Once the image is digitally zoomed in, use the mouse scroll button to further zoom on or zoom out the image. Hold and left-click on the image and move the mouse to move the zoomed in video.
38
SVR-‐632/664
U ser’s
M anual
Change Web UI Display Language You can change the web UI display language from the current login username link located at the upper-right hand corner. Click on the link opens up a new window which displays detail infor- mation about the user as well as a drop-down menu which lets you change the displyay language.
SVR-‐632/664
U ser’s
M anual
Live View through iPhone Safari Browser You can use iPhone and perform single channel live view to the NVR by using its Safari browser. To be able to view the live video through the Safari browser, make sure “javascript”...
Page 40
40
SVR-‐632/664
U ser’s
M anual
Type in the IP address of the NVR in the address bar...
Page 41
SVR-‐632/664
U ser’s
M anual
You should be prompted to enter the username and password to access the NVR...
Page 42
42
SVR-‐632/664
U ser’s
M anual
Upon successful login, you should see the live view video of the first channel...
Page 43
SVR-‐632/664
U ser’s
M anual
Click on the “Channel” drop-down menu to select other cameras...
44
SVR-‐632/664
U ser’s
M anual
If a PTZ camera is selected, the corresponding control buttons will display (control PT only) * Please note that this function is camera dependent and is not available to all cameras. Certain cameras do not allow adjusting image size and the selection “Auto”...
Page 45
SVR-‐632/664
U ser’s
M anual
Enable the “Support Javascript” option and click the menu button and click “Save Options” Go to “General Properties...
Page 46
46
SVR-‐632/664
U ser’s
M anual
Make sure two options illustrated above are enabled Press the menu button and click the “Save Options” to save settings...
Page 47
SVR-‐632/664
U ser’s
M anual
Press the button highlighted above to go back to the browser...
Page 48
48
SVR-‐632/664
U ser’s
M anual
Type in the IP address of the NVR in the address bar...
Page 49
SVR-‐632/664
U ser’s
M anual
You should be prompted to enter its username and password for access...
50
SVR-‐632/664
U ser’s
M anual
Playback Playback is a function that allows you to play one or more videos that were previously recorded by a chosen recording method or due to an event trigger. The NVR offers synchronized playback from up to 4 channels and various types of search methods are provided to help you find the footage you need quickly.
SVR-‐632/664
U ser’s
M anual
Search by time chart 1. Start by selecting which channel(s) you would like to perform a search on. 2. Select “Search by time chart” from the “Search Method” drop-down list and click “Go” to start the search * Selected channels will be marked in red...
Page 52
52
SVR-‐632/664
U ser’s
M anual
Results will then be displayed in a new dialog with a “Month/Channel” table and boxes marked in dark gray represent videos found in those dates. (* Videos from other cameras that are recorded on the same date will also be displayed )
SVR-‐632/664
U ser’s
M anual
Clicking on a cell box marked with gray will take you to the "day" view of the selected month. Repeating the same step will eventually take you to the "second" view (5sec per cell box). Right-click anywhere or the "Back"...
Page 54
54
SVR-‐632/664
U ser’s
M anual
Start by selecting which channel(s) you would like to perform a search Select “Search by event” from the “Search Method” drop-down list and click “Go” to start the search...
Page 55
SVR-‐632/664
U ser’s
M anual
Results will then be listed like what is shown below (displays the oldest record top down). Click on a particular result to start the playback. (* You can cilck “Next Search” to display the next 15 results.) You may also specify a new start time to search and display results from then on.
56
SVR-‐632/664
U ser’s
M anual
Play by specific time If you know when a recording was taken place, you may choose the “Play by start time” from the “Search Method” drop-down list Then you will be prompted to enter a specific time and date for the recorded video.
SVR-‐632/664
U ser’s
M anual
Search by event (Most Recent) This function quickly displays the most recent event recordings from the selected channels, displaying the most recent result top down.
Page 58
58
SVR-‐632/664
U ser’s
M anual
You may click “Update” to update the list to display the most recent results.
SVR-‐632/664
U ser’s
M anual
Certain functions you can perform to the playback video You can do the followings by right-clicking on the playback video: 1. Play Audio 2. Snapshot 3. Export as AVI file 4. Digital PTZ...
60
SVR-‐632/664
U ser’s
M anual
Export Playback Videos to AVI Files User can export the recorded playback videos stored on the NVR to a local computer and save them in AVI file format. The files can then be played on the PC by a 3rd party media player such as VLC player or Windows Media player.
Page 61
SVR-‐632/664
U ser’s
M anual
A new dialog will pop up and allows you to speficy the time frame (or length) of the video you wish to export...
Page 62
62
SVR-‐632/664
U ser’s
M anual
Specify the Start time/End time (or export length) and click "Start" to begin exporting. You will be notified once the process is completed successfully...
SVR-‐632/664
U ser’s
M anual
The exported AVI file will be saved under the C partition (or the partition where Windows is installed) * ffdshow is required in order to play the exported AVI file with Win- dows Media Player.
Page 64
64
SVR-‐632/664
U ser’s
M anual
You can also use the NVR Media Player to play the exported AVI files. This can save you the trouble of installing third-party media player or codecs when playing the exported AVI videos. The NVR Media Player will be automatically installed after the CMS software is installed.
Page 65
SVR-‐632/664
U ser’s
M anual
Locate the exported AVI file, and click “open”. (normally under “C:\ExportFolder)”...
66
SVR-‐632/664
U ser’s
M anual
The video will then start playing Open Event Snapshot images with NVR Media Player The NVR sends snapshots that are taken when an event occurs to a destined FTP server or mail recepient. These type of snapshot images...
SVR-‐632/664
U ser’s
M anual
are saved in a proprietary image file format, h4i or p4i, and can only be opened by the NVR media player. To do so, Select “Open” from the top menu then select “Image File”. A new dialog should be displayed which lets you locate the image file.
Page 68
68
SVR-‐632/664
U ser’s
M anual
correctly based on your network configurations so that the recorder can be administered through the local area network and cameras can be connected from it. By default, the recorder is set to obtain IP address from DHCP server, it should be sufficient in most network environments, and most likely you should not need to alter anything in this page.
SVR-‐632/664
U ser’s
M anual
2. Enter the IP address, subnet mask, default gateway address and DNS server address for the recorder 3. Enable “DHCP Server” under “DHCP Server” if you wish to use the recorder as a DHCP server, or leave it disabled if there is already a DHCP server in the network 4.
Page 70
70
SVR-‐632/664
U ser’s
M anual
*Please make sure a valid DNS server has been configured under the “Network Setting” page in order for this function to work properly. *The NVR currently only works with free DDNS service provided by “DynDNS”.
Page 71
SVR-‐632/664
U ser’s
M anual
In order to properly configure the DDNS service function, please register a free DDNS domain name and account from DynDNS first. Go http://dyn.com/dns/dyndns-free/ from the browser to do so.
Page 72
72
SVR-‐632/664
U ser’s
M anual
Fill in the necessary fields as illustrated above The page will check whether the hostname you entered has been used by another user or not as soon as you click the “Add to Cart” button. If...
Page 73
SVR-‐632/664
U ser’s
M anual
you see below message, simply enter a different and click “Add to Cart” again Once you get to the next page, fill in the necessary fields as illustrated above...
Page 74
74
SVR-‐632/664
U ser’s
M anual
Go back to the NVR’s DDNS service configuration page under “Setup” >> “System Configuration” >> “DDNS Service”. Fill in the domain name you picked during the registration in the “Domain Name” field and the username/password you created in the “User ID”...
Page 75
SVR-‐632/664
U ser’s
M anual
You can click the “Check DDNS Status” button to check the DynDNS service status. If you are getting a “Disconnected” message, it means that DDNS service server is down or the NVR is not connected to the Internet.
76
SVR-‐632/664
U ser’s
M anual
Time and Date Set the time and date by selecting the time zone according to your location. It is imperative that you set the recorder’s time correctly to avoid the following errors: •...
SVR-‐632/664
U ser’s
M anual
User Account The recorder can be accessed by multiple users simultaneously. You can add, remove, and edit users by using options provided in this page to keep user information organized. Each recorder comes with a built- in “admin”...
78
SVR-‐632/664
U ser’s
M anual
Add a new user • Enter a username and password in “User Account Information”. All other fields are optional for your own reference. • Select a group from the “Group” drop-down menu to assign the new user to a particular group •...
SVR-‐632/664
U ser’s
M anual
Change the password of the “admin” account 1. Click and highlight the “admin” account in the account list and click “Edit” 2. Its information should be displayed in “User Account Information” 3. Enter a new password in the “Password” field and enter it again in “Confirm Password”...
80
SVR-‐632/664
U ser’s
M anual
Group Privilege Group Privilege is where you can create multiple customized access policies for situations if you need the recorder to be accessed by us- ers other than the administrator. You can do so by creating a group, and then remove access privileges for certain configuration pages or cameras.
Page 81
SVR-‐632/664
U ser’s
M anual
To create a group, select a group from the “Group” drop-down You can change the group name by clicking the “Change Group Name” button. A text box will be displayed for you to enter the new group. Choose what type of privilege you would like this group to have from the “Privilege Type”...
Page 82
82
SVR-‐632/664
U ser’s
M anual
Its access privilege will then be displayed. You can alter its settings by allowing or denying access to other cameras using the checkboxes instead of accepting the defaults...
SVR-‐632/664
U ser’s
M anual
Disk Setup Once you install a hard disk to the recorder, you would need to initialize it so that it can be ready for recording. You can obtain basic information about the disk you installed in this page. To initialize it, simply click the “Format”...
84
SVR-‐632/664
U ser’s
M anual
Build RAID Volume The internal HDDs can be used for RAID. To do so, go to "RAID Volume" in Disk Setup and choose the availabe disk action. The "Disk Actions" drop-down menu displays available actions based on how many HDDs are installed in the NVR.
Page 85
SVR-‐632/664
U ser’s
M anual
Select a disk action and click "Apply" to proceed. A warning dialog will be displayed as creating RAID volume will erase all existing data on the HDDs. Click "OK" to continue.
Page 86
86
SVR-‐632/664
U ser’s
M anual
Please wait for a few moment while the NVR is creating the RAID volume. You will be prompted once the action is completed successfully.
Page 87
SVR-‐632/664
U ser’s
M anual
Once the RAID volume is created, it will be listed in the "RAID volume list with the status of "Offline"...
Page 88
88
SVR-‐632/664
U ser’s
M anual
Go back to the "Hard Disk List" page and the RAID volume should be in the list. Click "Format" to bring the RAID volume online. The status will be displayed just as if you were formating any internal HDDs...
SVR-‐632/664
U ser’s
M anual
Deleting RAID Once a RAID volume is created, it can be deleted at anytime by choosing the "Delete RAID" action in the RAID volume page. All existing data will be removed after the RAID volume is deleted. All internal disks that were originally used for RAID volume will have to be formatted again after the RAID volume is deleted.
Page 90
90
SVR-‐632/664
U ser’s
M anual
* Once a RAID volume is deleted, all internal disks within that RAID should become offline and need to be formatted again before they can be used individually. * All internal disks (or RAID volumes) need to be formatted before they can be used.
SVR-‐632/664
U ser’s
M anual
NVR Setup -- Channel Configurations Add a camera The NVR provides two options for adding a new camera. Users have the option to let the recorder automatically find the cameras or it is possible to enter camera’s information and add it manually.
Page 92
92
SVR-‐632/664
U ser’s
M anual
Click the “Search” button to perform the camera search. You should be prompted to install Active Control component the first time you visit the page in order for the search to function properly. Go ahead and click “Install”...
Page 93
SVR-‐632/664
U ser’s
M anual
Its corresponding information should be displayed in the “Camera Information” section. Enter its username and password and select the channel ID and name the camera. Click on “Detect” to establish connection between the recorder and the camera.
Page 94
94
SVR-‐632/664
U ser’s
M anual
Adjust its video format, frame rate, resolution or bitrate...etc if you wish. You can also click on the “Preview” to preview the live video of the camera. Click “Add” to finish adding the camera *If cameras are marked with "*"...
Page 95
SVR-‐632/664
U ser’s
M anual
Once the camera's settings are polled and displayed, you can also enable "continuous" recording and adjust its recording quality settings before adding the camera. Some cameras are capable of multiple streaming profiles, in which different video codecs are used for different purposes.
Page 96
96
SVR-‐632/664
U ser’s
M anual
There are two types of fps settings here, one is the fps that NVR sets back to the camera, and this is the fps NVR will be receiving from the camera.
SVR-‐632/664
U ser’s
M anual
Add a camera manually Simply follow the instruction described above but instead of using the “Search” function, enter the camera’s IP address and cre- dential in the “Camera Information” manually.
98
SVR-‐632/664
U ser’s
M anual
OSD Settings The OSD (On Screen Display) allows users to add informational text message and embed it onto the video. By default, this function is turned off. To add texts to one or more videos. Select a camera you would like to add text to and choose “Display OSD”...
Page 99
SVR-‐632/664
U ser’s
M anual
Next, define where the text will be displayed by either entering an X/Y coordinate or use the system pre-defined position from the drop-down menu. Click on the “Preview” button to see the preview of your setting and click “Apply”...
Page 100
SVR-‐632/664
U ser’s
M anual
0
The texts can be further adjusted with changes to different size, color or font so they can be more visible on the video.
SVR-‐632/664
U ser’s
M anual
PTZ Setting PTZ Preset Settings The recorder supports PTZ cameras and can set multiple preset points or retrieve and manage preset points that are set in the camera. This is helpful if you need to monitor multiple spots in one area from a particular camera.
Page 102
SVR-‐632/664
U ser’s
M anual
2
To set up PTZ preset points: 1. Select a camera from the “Camera” drop-down menu and click “Add”. 2. Select a position number for the preset point from the “Position Number”...
SVR-‐632/664
U ser’s
M anual
Ultimately, you can choose to make this preset point a “Home” point among all other preset points, as well as making the camera to move to this particular point when an event is triggered. * “Move Here when Event Trigger”: In order for this function to work properly, please also complete configuration in “Event Configuration”...
Page 104
SVR-‐632/664
U ser’s
M anual
4
To configure preset sequence for a camera, 1. Select a channel from the “Channel” drop-down menu. The available preset points should be listed in “Camera Presets” section. 2. Pick the ones you like for sequence viewing and press the “->” button to move them to the “Preset Sequence”...
SVR-‐632/664
U ser’s
M anual
E-Map Setting Local E-Map Setting E-Map monitor is a function that alerts users whenever there is an event triggered (e.g. motion detected) from a camera with a geographical perspective. With this function, users can quickly identify which camera has detected an unusual event and where this event is happening.
Page 106
SVR-‐632/664
U ser’s
M anual
6
To replace the map, click “Browse” button to locate the new map image file from the local PC and then click “Upload”. * Only JPG, PNG, and GIF file formats are supported with file size under 100KB.
Page 107
SVR-‐632/664
U ser’s
M anual
Then click and drag the camera icon to move the camera to define its location. Access the E-Map Monitor page from the upper-right hand corner menu. When the NVR receives an event triggered from any of the cameras, their videos will be displayed on the E-Map and you can double-click on the video to enlarge it.
SVR-‐632/664
U ser’s
M anual
8
Google Map Setting The Google Map monitor is a similar function to the aforementioned E- Map monitor. It is useful if you are managing multiple cameras from different locations. To configure locations of each camera, first determine the location you’d like to place the camera to on the map.
Page 109
SVR-‐632/664
U ser’s
M anual
1. Zoom in to a smaller area by using the zoom control bar on the map 2. Zoom in to a smaller area by using the mouse scroll button You can also go to a specific place on the map by entering its address or the name of the place in the “Address or places of interest”...
SVR-‐632/664
U ser’s
M anual
0
NVR Setup -- Event Configurations Event Configuration The “Event Configurations” section allows users to define conditions that constitute an event, its corresponding trigger action and when it will be triggered. Such setting can reduce the management overhead and notify the administrator only when it’s necessary.
Page 111
SVR-‐632/664
U ser’s
M anual
and “End Time” fields that you would like the event trigger function to be enabled. How often an event is triggered • Set a time interval under “Event Trigger Interval” to define how often events are triggered Trigger action Now that you have the event trigger duration and interval defined,...
SVR-‐632/664
U ser’s
M anual
2
I/O Settings This function allows users to manage camera’s digital input and output ports right from the recorder. You can setup the recorder to receive triggers from a particular camera’s input port and trigger a device, such as an alarm that is connected to the recorder or camera’s output port.
Page 113
SVR-‐632/664
U ser’s
M anual
*Only connected cameras will be displayed in the list. *Some cameras only allow one trigger source be configured at a time, e.g.: if the camera has the motion detection function turned on, its digital input will be disabled and vice versa.
SVR-‐632/664
U ser’s
M anual
4
Event Servers Configuring an FTP server Event servers are to be used with event trigger actions. In case of unusual motion detected by the camera or a disk failure, the recorder can send notification with the acceptable format (image/txt) to a destined event server according to the configuration.
Page 115
SVR-‐632/664
U ser’s
M anual
To add an FTP server, 1. Start by giving a name to the server that you are adding to the recorder 2. Enter the hostname or the IP address of the FTP server 3.
SVR-‐632/664
U ser’s
M anual
6
Configuring an SMTP server 1. Enter the hostname or the IP address of the SMTP server 2. Enter the port of the SMTP server 3. Specify the sender’s name in the “Sender’s name” field 4.
SVR-‐632/664
U ser’s
M anual
Event Triggers We have finished defining how an event will be triggered and which servers will be receiving notifications in the previous two sections, now we can finish up the event configuration by setting: •...
Page 118
SVR-‐632/664
U ser’s
M anual
8
Use the checkbox to enable event trigger on the desired channels. *Once motion detection is enabled in this page, please configure the motion area and enable motion detection in the corresponding channels (cameras) from camera's own web UI.
SVR-‐632/664
U ser’s
M anual
NVR Setup -- Recording Configurations General Settings The “recording configurations” gives users the overall control of how and when a recording is performed and the quality of different types of recordings performed on each channels. It can help the recorder to operate with sufficient system resource by performing recording only when it’s necessary with adjustable recording frame rate.
Page 120
SVR-‐632/664
U ser’s
M anual
0
The “recording buffer” allows user to define “pre-alarm” and “post- alarm” time for event recordings. The “pre-alarm” time sets the NVR to record in advance when an event is triggered. The “post-alarm” time sets the NVR to continue recording for a period of time after an event trigger is finished.
Page 121
SVR-‐632/664
U ser’s
M anual
only. Use the drop-down menu and select one of the pre-defined frame rates for a particular recording type You are able to use the same video format for recordings or you can choose other formats for different recording purposes if it's a multi- stream capable cameras.
Page 122
SVR-‐632/664
U ser’s
M anual
2
Users can also set to keep a previous number of days of recording data by enabling the option below. This is quite often used in applica- tion such as banking which certain countries requires to always keep a minimum previous number of days of recording data.
Page 123
SVR-‐632/664
U ser’s
M anual
The section at the bottom of the page allows you to disable audio recording (record video only) of particular channels.
SVR-‐632/664
U ser’s
M anual
4
Schedule Recording You can define the time range of the schedule recording for all channels in this page. To configure a schedule recording Use the “Channel” drop-down menu and select a camera first.
Page 125
SVR-‐632/664
U ser’s
M anual
You can use the schedule table to set the time range. Click the cell boxes then move horizontally lets you set what hours to perform recording during a day. Click and move vertically lets you set what days to perform recording at a specific time.
SVR-‐632/664
U ser’s
M anual
6
Select the “Copy to” option if you would like to set the same re- cording schedule to another camera. NVR Setup -- System Options Device Information System Options gives users a glance of the overall system status and allows users to perform maintenance tasks such as upgrading firm- ware, restore/backup device settings or reboot device ..etc.
SVR-‐632/664
U ser’s
M anual
Logs and Reports “Logs and Reports” keeps a record of what’s been happening to the device and provides basic information for troubleshooting.
SVR-‐632/664
U ser’s
M anual
8
Maintenance “Maintenance” provides functions for users to: • Reboot the NVR when necessary • Reboot cameras directly from the NVR • Perform Firmware Upgrade • Backup the NVR’s settings to a local hard drive •...
SVR-‐632/664
U ser’s
M anual
Reboot the NVR at a specific time automatically You can configure the NVR to restart automatically by using the options given in the web UI. You can set the NVR to restart at a particular hour of a specific day during a week or a month.
Page 130
SVR-‐632/664
U ser’s
M anual
0
Login into NVR’s web management UI. Go to "Setup" page and go to "System Options"->"Maintenance" On "Upgrade NVR's Firmware" section, click "Browse" and select new firmware file A new dialog should display and let you choose the location of the firmware file.
Page 131
SVR-‐632/664
U ser’s
M anual
When done, click “Upgrade”. Follow the on screen instruction and wait for the process to finish (After upgrade, the system will reboot automatically, it’s part of the process)
SVR-‐632/664
U ser’s
M anual
2
Upgrade through USB thumb drive 1. Prepare a USB flash disk and format with FAT or FAT32 format 2. Place the firmware in the USB flash disk and make sure it’s placed at the top-level directory.
Page 133
SVR-‐632/664
U ser’s
M anual
The process should be displayed and you should be prompted back to the “Live View” page after it is complete.
SVR-‐632/664
U ser’s
M anual
4
Disk Status “Disk Status” gives you a more detailed information of the hard drive that is currently installed in the NVR.
SVR-‐632/664
U ser’s
M anual
USB Backup It’s a function that allows users to backup the recording data in its database file format (not AVI) to the externally connected USB hard disk. You can check the “Disk Status” page under “System Options” to see if the USB disk has been detected by the NVR.
Page 136
SVR-‐632/664
U ser’s
M anual
6
Once it’s detected, go back to the “USB Backup” page and it should be available for further configuration The USB hard disk(s) will be listed in the drop-down menu displaying the remaining disk space.
SVR-‐632/664
U ser’s
M anual
Next, select channels which you would like to backup the recording data from. Maximum 4 channels can be selected at once Configure the start and end time of the recording data you would like to backup and click the “Backup”...
Page 138
SVR-‐632/664
U ser’s
M anual
8
Process: • Progress will be displayed on the UI • If the backup process gets interrupted, which the process stops at a point of time that is before the “END Time” user defined, such time will be displayed on the UI •...
Page 139
SVR-‐632/664
U ser’s
M anual
Click “Browse...” to select the file from the USB disk. A new dialog should be prompted for you to select the file location.
Page 140
SVR-‐632/664
U ser’s
M anual
0
When done, click “Check” to validate the file. Once the file has been successfully verified, you should be prompted with the message shown below.
Page 141
SVR-‐632/664
U ser’s
M anual
Select the time zone according to your current location. Finally, click “OK” to begin playing. The player should now play the backed up file.