Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Riello VST 800
Summary of Contents for Riello VST 800
- Page 2 NTRODUCTION Congratulations on purchasing a UPS Vision product and welcome to Riello UPS! To use the support service offered by Riello UPS, visit the site www.riello-ups.com Our Company is a specialist in the design, development and manufacturing of uninterruptible power supplies (UPS).
-
Page 3: Table Of Contents
ONTENTS PRESENTATION UPS V IEWS RONT VIEW EAR VIEW ISPLAY PANEL VIEW INSTALLATION NITIAL CONTENT CHECK NSTALLATION ENVIRONMENT ONNECTIONS AND SWITCHING ON FOR THE FIRST TIME WITCHING ON FROM THE MAINS ... -
Page 4: Presentation
PRESENTATION The VISION series is the ideal solution for high end users who require high security and versatility from their power systems. The VISION is the best protection system available for network devices, servers and conventional storage systems. The VISION series is a range of UPS which utilises the very latest Line Interactive technology and sinusoidal output voltage waveforms. -
Page 5: Ups Views
UPS V IEWS RONT VIEW Display Removable front panel Multipurpose buttons Battery pack connector ON/OFF Switch Battery pack retention panel... -
Page 6: Rear View
EAR VIEW 800VA / 1100VA Model 1500VA / 2000VA Model Communication port RS232 Cooling fans USB communication port IEC 10A output socket Circuit breaker Energyshare Communication Card Slots IEC 10A input plug... -
Page 7: Display Panel View
ISPLAY PANEL VIEW “SEL” button (Select) Load level indicator “ON” button Configuration area “STAND-BY” button Maintenance request Regular operation Timer Mains operation Measurement display area Battery operation Stand-by / alarm AVR active EnergyShare Battery charge indicator... -
Page 8: Installation
INSTALLATION NITIAL CONTENT CHECK After opening the packaging, it is first necessary to check the contents. The package must contain: Schuko power cable - IEC 10A 2 IEC 10A connection cables USB cable RS232 cable User manual CD + Safety manual NSTALLATION ENVIRONMENT The UPS and the Battery Box must be installed in ventilated, clean environments which are sheltered from bad weather. -
Page 9: Use
6) Check which operating mode is set on the display and, if necessary, see the “Configuring operating modes” paragraph to set the required mode. For advanced UPS configurations execute the software UPSTools which can be downloaded from the web site www.riello-ups.com. WITCHING ON FROM THE MAINS 1) Press the “ON”... -
Page 10: Display Panel Messages
ISPLAY PANEL MESSAGES This chapter describes, in detail, the various information that can be displayed on the LCD. STATUS MESSAGES ICON STATUS DESCRIPTION Fixed Indicates a fault Flashing The UPS is in stand-by mode Fixed Indicates regular operation Fixed The UPS is operating from the mains The UPS is operating from the battery. -
Page 11: Measurement Display Area
EASUREMENT DISPLAY AREA The front panel can be used to display important UPS operating information. When the UPS is switched-on, the display shows the main voltage value. To display a different measurement, press the “SEL” button repeatedly until the desired measurement appears. In the event of a fault/alarm (FAULT) or a lock (LOCK), the display will automatically show the type and code of the corresponding alarm. -
Page 12: Configuring The Operating Mode
ONFIGURING THE OPERATING MODE The area of the display shown in the figure displays the active operating mode and allows the user to choose other modes directly from the display panel. HOW TO PROCEED: • To access the configuration area, hold down the “SEL” button for at least 3 seconds. •... -
Page 13: Software
2) Download the software from the web site www.riello-ups.com selecting the specific operating system. 3) Follow the installation program instructions. 4) For more detailed information please read the user manual which can be downloaded from www.riello- ups.com. ONFIGURATION SOFTWARE The UPStools software allows the configuration and full display of the status of the UPS via USB or RS232. -
Page 14: Ups Configuration
CONFIGURATION The table below illustrates all the possible configurations available to the user in order to best adapt the UPS for individual requirements. It is possible to perform these operations using the UPStools software. FUNCTION DESCRIPTION DEFAULT POSSIBLE CONFIGURATIONS • 50 Hz Selects the nominal output •... -
Page 15: Communication Ports
Serial duplicator • Ethernet network card with TCP/IP, HTTP and SNMP protocols • JBUS / MODBUS protocol converter card • PROFIBUS protocol converter card • Card with relay isolated contacts To check the availability of other accessories, visit the website www.riello-ups.com. -
Page 16: Battery Pack Replacement
ATTERY PACK REPLACEMENT The UPS is also equipped with a dedicated battery pack that allows for easy replacement of batteries (hot swap) in complete safety, thanks to the protected connection system. • WHEN THE BATTERY PACK IS DISCONNECTED, THE LOADS CONNECTED TO THE UPS ARE NOT PROTECTED IN THE EVENT OF A MAINS FAILURE •... - Page 17 Remove the battery pack's retention panel carrying out the operations shown in the figure below. Slip off the battery pack pulling it towards the outside, as shown in the figure below. Be careful when extracting and lifting up the battery pack as it is heavy.. ATTENTION: the new battery pack must contain the same number and type of batteries (see the label located on the battery pack near the connector).
-
Page 18: Troubleshooting
TROUBLESHOOTING Irregular UPS operation is not always an indication of a fault, and can be due to minor or easy-to-resolve issues It is therefore advisable to consult the table below as it contains information which is useful for solving the most common UPS problems. - Page 19 The UPS in case of a permanent failure will be not able to supply the load. To ensure total protection of your equipment we suggest you install an ATS device (Automatic Transfer Switch) or an external automatic by-pass. For more information visit www.riello-ups.com...
-
Page 20: Alarm Codes
LARM CODES Using a sophisticated self-diagnosis system, the UPS is able to check its own status for any anomalies and/or faults which may occur during normal operation and display them on the display panel. If there is a problem, the UPS signals the event by showing the code and the type of active alarm on the display (FAULT and/or LOCK). -
Page 21: Lock
Active commands: Indicates the presence of an active remote command. CODE DESCRIPTION Remote control 1 (Switch On/Off) Remote control 2 (Load supplied by the mains) Remote control 3 (Switch On/Off) Battery test in progress LOCK alerts are normally preceded by an alarm signal and their scale leads to the powering-off of the inverter with the load being powered by the bypass line (this procedure is excluded for locks due to serious, persistent overloads and short circuits). -
Page 22: Technical Data
17.5 18.5 For additional details regarding technical data refer to website www.riello-ups.com @ rated load, rated voltage of 220 Vac, battery charging To maintain output voltage within the accuracy range specified, recalibration may be necessary after a long period of operation...